MINI Clubman 2016 Owner's Manual

Adding1.Let the engine cool.2.Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres~
sure to dissipate, then open it.3.If the coolant is low, slowly add coolant up
to the specified level; do not overfill.4.Close cap.5.Have the cause of the coolant loss elimi~
nated as soon as possible.
Disposal
Comply with the relevant environmen~tal protection regulations when dispos~ ing of coolant and coolant additives.
Seite 211CoolantMOBILITY211
Online Edition for Part no. 01 40 2 972 253 - VI/16

MaintenanceVehicle
features
and
op

service center or repair shop. Records of regu~
lar maintenance and repair work should be re~
tained.
Socket
for
OBD
Onboard
Diagnosis
Safety
information NOTE
The socket for Onboard Diagnosis is an
intricate component intended to be used in
conjunction with specialized equipment to
check the vehicle

Replacing
componentsVehicle
features
and
op

3.Continue turning the wiper blade all the
way so that it pops out of the holder.4.Press the new wiper blade into the holder
until you hear it snap into place.5.Fold the wipers in.
Lamp
and
bulb
replace

Front
lights,
bulb
replacement
Overview
Halogen
headlights1Low beams/high beams2Turn signal
LED
headlights
1Daytime running lights2Low beams/high beams3Turn signalBug
light1Parking lights2Daytime running lights3Fog lights
LED
bug
light
1Parking lights2Fog lights
LED
low
beams/LED
high
beams Follow the general instructions on lights andbulbs, refer to page 215.
The lights feature LED technology. In the case
of a malfunction, contact a dealer

Bulbs: H41.Open the hood, refer to page 205.2.Turn the lid counterclockwise, arrow, and
remove.3.Pull off the connector.4.Unclip spring clip, arrow, and fold down.5.Remove the bulb from the headlight hous~ ing.6.Insert the new bulb and install the cover in
the reverse order.
Turn
signal
Follow the general instructions on lights and
bulbs, refer to page 215.
Bulbs: PW24W
With white turn signal lights: PWY24W1.Turn the steering wheel.2.Turn the lid counterclockwise, arrow 1, and remove.3.Unscrew the inner lid counterclockwise,and remove it.4.Pull bulb holder out of the bulb housing; ifneeded, loosen it with small tilting move~ments if possible.5.Pull the bulb out of the fixture.6.Insert the new bulb and install the cover in
the reverse order.Seite 217Replacing
componentsMOBILITY217
Online Edition for Part no. 01 40 2 972 253 - VI/16

LED
parking
lights/LED
fog
lightsFollow the general instructions on lights and
bulbs, refer to page 215.
The lights feature LED technology. In the case of a malfunction, contact a dealer

Tail
lamps
in
split
doors1Turn signal2Tail lamps3Rear fog lamp4Reversing lights
LED
tail
lights
in
the
split
doors
1Turn signal2Tail lamps3Rear fog lamp4Reversing lightsTail
lamps
in
bumpers1Tail lamps/brake lights2Turn signal
In addition, the tail lamps in the bumper as~sume the functions of tail lamp and turn sig~
nals, if the split doors are open.
Tail
lamps
in
split
doors
Follow the general instructions on lights and
bulbs, refer to page 215.
Turn
signals/tail
lamps
Bulbs: P21W/W5W
1.Opening split doors, refer to page 41.2.Remove left or right cover. If necessary, it is
then possible to pry the cover off using ascrewdriver or a similar plastic tool.3.Press the latches together upward, arrow 1,and remove the bulb holder.Seite 219Replacing
componentsMOBILITY219
Online Edition for Part no. 01 40 2 972 253 - VI/16

Loosen the plug connector, arrow 2, on the
bulb holder.4.Remove the bulb holder from the opening.5.Press the nonworking bulb gently into the socket, turn counterclockwise and remove.'