MINI Convertible 2018 Workshop Manual

Power
windowsGeneral
information
If an accident of a certain severity occurs, the
windows are automatically closed except a
gap.
Safety
information WARNING
When operating the windows, body parts
and objects can be jammed. There is a risk of
injury or risk of damage to property. Make sure that the area of movement of the windows is
clear during opening and closing. '

Safety
informationWARNING
Accessories on the windows such as an~
tennas can impact jam protection. There is a risk of injury. Do not install accessories in the
area of movement of the windows. '

Sliding
sun
roof
General
information
Before closing the sliding sun roof, remove any
foreign objects from the windshield frame; oth~ erwise, closing may be prevented.
Opening Press the switch backward, until
the desired position is reached
or the sliding sun roof is fully
open.
Closing Press the switch forward, untilthe desired position is reached
or the sliding sun roof is closed.
Convertible
top
General
information
The convertible top can be opened or closed at
speeds up to approx. 18 mph/30 km/h.
If the vehicle is accelerated above a speed ofapprox. 18 mph/30 km/h while the convertibletop is being moved, the convertible top move~
ment stops.
Follow the following information:'

'

message is displayed when the opening proce~
dure has finished.
The convertible top movement is interrupted if
the switch is released. The sequence can be continued in the desired direction using the
switch.
Operate switch again until the convertible op~
eration is terminated.
Operating
from
the
outside
When equipped with Comfort Access the convertible top can also be operated from out~side.'

inside, arrow 1, and then toward the front,arrow 2.4.Turn the cover under the trim as far out~
ward as possible.5.Loosen and remove the two screws on both sides of the vehicle using the hexagonwrench.6.Only on the left side of the vehicle: slightly
lift the side frame, arrow 1, and pull the sensor with the cable forward out from theguide, arrow 2.Swivel the cable out sideways so it cannotbe pinched.
Closing
the
convertible
top
1.Grasp the convertible top with two people,
with both hands on the two side frames.2.Lift out the convertible top simultaneously on both sides and swivel forward onto thewindshield panel.
To take out the convertible top, pull force~
fully on the side frame. Begin with an up~
ward movement and then change to a for~
ward movement.3.In the vehicle, lift the cover in the center of
the roof using the screwdriver. Apply the screwdriver to the recesses, arrows.Seite 56CONTROLSOpening
and
closing56
Online Edition for Part no. 01402983394 - X/17

4.For this purpose, insert the hexagon
wrench into the designated receptacle in
the center of the roof and press push up~
ward, arrow 1.
Turn the hexagon wrench counterclockwise to open the side frame lock.5.Pull of the locking elements from the pins
on the left and right side of the side frames,
arrow.6.Insert the pins on the side frames into the
receptacles on the windshield frame.7.Turn the hexagon wrench clockwise to
close the side frame lock.8.Continue turning the hexagon wrench
clockwise to close the sliding sun roof.Wind
deflector
Concept The wind deflector reduces the air movementin the car's interior when driving with the
convertible top down.
Safety
information NOTE
When moving the front seats back, the
wind deflector can be damaged. There is a risk of damage to property. Make sure that the areaof movement is clear prior to moving the frontseats back. '

Fully unfold the wind deflector so that thehandle, arrow 1, folds down and locks the
wind deflector.2.Open the rear side window, if necessary.
Insert wind deflector from one side of the
vehicle with the pins in the corresponding fixing points on the opposite side of the ve~
hicle.3.To release the lock, fold the handle up and hold it.4.Press the wind deflector inwardly and up,arrow 1, to the extent that the wind deflec~
tor can be positioned in front of the fixing
points on the installation side.
Release the handle.Press the wind deflector downward, while
inserting the pins in the corresponding fix~ ing points, arrows 2.5.Press the wind deflector downward in themiddle, until the handle engages, arrows 1.
Grasp the inner framework of the wind de~
flector and fold it up, arrow 2.
Removing
Proceed in reverse sequence.
Seite 58CONTROLSOpening
and
closing58
Online Edition for Part no. 01402983394 - X/17

SettingsVehicle
features
and
op

Forward/backward
Pull the lever and slide the seat in the desired
direction.
After releasing the lever, move the seat forward or back slightly making sure it engages prop~
erly.
Height
Pull the lever up or press it down as often as
needed to reach the desired height.
Backrest
tilt
Pull the lever and apply your weight to the
backrest or lift it off, as necessary.
Lumbar
support
The curvature of the seat backrest can be ad~
justed in a way that it supports the lumbar re~
gion of the spine. The lower back and the spine
are supported for upright posture.
Turn the wheel in order to increase or decrease the curvature.
Thigh
support
Pull the lever at the front of the seat and adjust
the thigh support.
Entering
the
rear
Safety
information WARNING
There is a risk of jamming when moving
the seats. There is a risk of injury or risk of dam~ age to property. Make sure that the area ofmovement of the seat is clear prior to any ad~
justment. '