MINI COOPER 2018 Owners Manual

5.Make sure that the vehicle jack foot standsvertically and at a right angle beneath thejacking point.6.Make sure that the vehicle jack foot standsvertically and perpendicularly beneath the
jacking point after extending the vehicle
jack.7.Crank up the vehicle jack until the entire
surface of the jack is in contact with the
ground and the wheel in question is raised
a maximum of 1.2 inches/3 cm off the ground.
Mounting
a
wheel
Mount one emergency wheel only, as required.
1.Unscrew the lug bolts.2.Remove the wheel.3.Put the new wheel or emergency wheel on
and screw in at least two lug bolts in a crosswise pattern until hand-tight.
If non-original light-alloy wheels of the ve~
hicle manufacturer are mounted, the ac~
companying lug bolts may have to be used
as well.4.Hand-tighten the remaining lug bolts and
tighten all lug bolts well in a crosswise pat~
tern.5.Turn the vehicle jack crank counterclock~
wise to retract the vehicle jack and lower
the vehicle.6.Remove the vehicle jack and stow it se~ curely.
After
the
wheel
change
1.Tighten the lug bolts crosswise. The tight~
ening torque is 101 lb ft/140 Nm.2.Stow the nonworking wheel in the cargo
area, if necessary.
The nonworking wheel cannot be stored
under the cargo floor panel because of its
size.3.Check tire inflation pressure at the next op~
portunity and correct as needed.4.Reinitialize the run-flat tires.
Reset the Tire Pressure Monitor TPM.5.Check to make sure the lug bolts are tight with a calibrated torque wrench.6.Have the damaged tire replaced at the
nearest dealer

Safety
informationWARNING
The emergency wheel has particular di~
mensions. When driving with an emergency wheel, changed driving properties may occur,
for instance reduced lane stability when brak~ ing, longer braking distance, and changed self-
steering properties in the limit area. There is a risk of an accident. Drive moderately and do
not exceed a speed of 50 mph/80 km/h. '

Engine
compartmentVehicle
features
and
op

WARNING
The engine compartment accommodates
moving components. Certain components in the engine compartment can also move with
the vehicle switched off, for instance the radia~
tor fan. There is a risk of injury. Do not reach
into the area of moving parts. Keep articles of
clothing and hair away from moving parts. '

Engine
oilVehicle
features
and
op

Displaying
the
engine
oil
level
Via the Central Information Display (CID):1. "Vehicle info"2."Vehicle status"3. "Engine oil level"
The engine oil level is displayed.
System
limits
When making frequent short-distance trips or using a dynamic driving style, it may not be
possible to calculate a measured value. In this
case, the measured value for the last, suffi~
ciently long trip is displayed.
Detailed
measurement
Concept
The engine oil level is checked when the vehi~ cle is stationary and displayed via a scale.
If the engine oil level is outside its permissibleoperating range, a Check Control message is
displayed.
General
information
During the measurement, the idle speed is in~
creased somewhat.
Functional
requirements
'

NOTE
Too much engine oil can damage the en~
gine or the catalytic converter. There is a risk of
damage to property. Do not add too much en~ gine oil. When too much engine oil is added,
have the engine oil level corrected by a dealer

quested from a dealer

CoolantVehicle
features
and
op

Adding1.Let the engine cool.2.Turn the lid of the coolant reservoir slightly
counterclockwise to allow any excess pres~
sure to dissipate, then open it.3.If the coolant is low, slowly add coolant up
to the specified level; do not overfill.4.Close the cap.5.Have the cause of the coolant loss elimi~
nated as soon as possible.
Disposal
Comply with the relevant environmen~tal protection regulations when dispos~ ing of coolant and coolant additives.
Seite 230MOBILITYCoolant230
Online Edition for Part no. 01402983336 - X/17