start stop button MINI COOPER CONVERTIBLE 2014 Owners Manual

Instrument lighting  77Trip odometer  655Windshield wipers   596Start/stop the engine and switch
the ignition on/off   557Ignition lock  558Steering wheel buttons, rightResuming cruise control   94Storing the speed and accelerat‐
ing or slowing down   94Activating/deactivating cruise
control   93Steering wheel buttons, leftVolumeTelephone   138Change the radio station
Select a music track
Scroll through the redial list9Horn, the entire surface10Adjust the steering wheel   4911Releasing the hood  169Seite 13CockpitAt a glance13
Online Edition for Part no. 01 40 2 911 475 - VI/13

▷Starting the engine.▷MINI Convertible: Convenient closing and
convertible top operation with the remote
control for Comfort Access.▷MINI Coupe, MINI Roadster: closing the side
windows.
Functional requirements
▷There are no external sources of interfer‐
ence in the vicinity.▷To lock the vehicle, the remote control
must be located outside of the vehicle.▷The next unlocking and locking cycle is not
possible until after approx. 2 seconds.▷The engine can only be started if the re‐
mote control is inside the vehicle.▷The doors and tailgate must be closed to
operate the windows.
Comparison with ordinary remote
control
The functions can be controlled by pressing the
buttons or via Comfort Access.
Notes on opening and closing, refer to page 20.
If you notice a brief delay while opening or
closing the windows or convertible top, the sys‐
tem is checking whether a remote control is in‐
side the vehicle. Repeat the opening or closing
procedure, if necessary.
Unlocking
Press button 1.
Depending on the setting, either only the driv‐
er's door or the entire vehicle is unlocked, refer
to page 22.
Pressing the button again locks the entire vehi‐
cle again.
Convenient opening with the remote control,
refer to page 23.
Locking
Press button 1.
MINI Convertible, MINI Roadster:
windows and convertible top operation
In the radio ready state and beyond, the win‐
dows and the electrical convertible top can be
opened and closed when a remote control is lo‐
cated inside the vehicle.
Unlocking the tailgate separately Press the button on the exterior of the tailgate.
This corresponds to pressing the following but‐
ton on the remote control:
.
If a remote control accidentally left in the cargo
area is detected in the locked vehicle after the
tailgate is closed, the tailgate opens again
slightly. The hazard warning system flashes and
an acoustic signal sounds.
Power windows When the engine is switched off, the windows
can be operated as long as neither the doors
nor the tailgate are opened.
When the door and tailgate are closed again
and the remote control is detected inside the
vehicle, the windows can be operated again.
Insert the remote control into the ignition lock
to be able to operate the windows while the
engine is switched off and the doors are open.
Switching on the radio ready state Press the Start/Stop button to switch on the
radio ready state, refer to page 55.
Seite 29Opening and closingControls29
Online Edition for Part no. 01 40 2 911 475 - VI/13

DrivingVehicle equipmentThis chapter describes all series equipment as
well as country-specific and special equipment
offered for this model series.Therefore, it also
describes equipment that may not be found in
your vehicle, for instance due to the selected
special equipment or the country version. This
also applies to safety-related functions and sys‐
tems.
Ignition lock Insert the remote control into the
ignition lock
Insert the remote control all the way into the
ignition lock.
Radio ready state is switched on. Individual
electrical consumers can operate.
Removing the remote control from the
ignition lock
Do not forcibly pull the remote control
out of the ignition lock
Do not forcibly pull the remote control out of
the ignition lock as this may cause damage. ◀
Before removing the remote control, push it all
the way in to release the locking mechanism.
The ignition is switched off if it was on.
Automatic transmission
You can only take out the remote control if
transmission position P is engaged: interlock.
Start/Stop button
Pressing the Start/Stop button switches the ig‐
nition on or off and starts the engine.
The engine starts when the Start/Stop button is
pressed and:
▷Manual transmission: the clutch is de‐
pressed.▷Automatic transmission: the brake is de‐
pressed.
Radio ready state
Individual electrical consumers can operate.
Radio ready state is switched off automatically:
▷When the remote control is removed from
the ignition lock.▷With Comfort Access, refer to page 28, by
pressing the button on the door handle or
the
button on the remote control.
▷After a certain period of time.
Ignition on All electrical consumers can operate. Most indi‐
cator and warning lamps light up for different
lengths of time.
Seite 55DrivingControls55
Online Edition for Part no. 01 40 2 911 475 - VI/13

To save battery power when the engine is off,
switch off the ignition and any unnecessary
electronic systems/power consumers.
Radio ready state and ignition off All indicator and warning lamps in the displays
go out.
The ignition switches off automatically when
the driver's door is opened. Pressing the Start/
Stop button again switches the ignition back
on.
For example, the ignition is not switched off in
the following situations:▷Depress the clutch or brake pedal.▷The low beams are switched on
Starting the engine
General information Enclosed areas
Do not let the engine run in enclosed
areas; otherwise, breathing of exhaust fumes
may lead to loss of consciousness and death.
The exhaust gases contain carbon monoxide,
an odorless and colorless but highly toxic gas. ◀
Unattended vehicle
Do not leave the car unattended with the
engine running; otherwise, it presents a poten‐
tial source of danger.
Before leaving the car with the engine running,
shift to neutral or engage transmission posi‐
tion P and set the handbrake firmly; otherwise,
the vehicle may begin to roll. ◀
Frequent starting in quick succession
Avoid repeated futile attempts at starting
the car and avoid starting the car frequently in
quick succession. Otherwise, the fuel is not
burned or is inadequately burned, and there is
the danger of overheating and damaging the
catalytic converter. ◀
Do not wait for the engine to warm-up while
the vehicle remains stationary; start driving
right away, but at moderate engine speeds.
Do not depress the accelerator when starting
the engine.
Starting the engine
Manual transmission
Remote control in the ignition lock or, with
Comfort Access, inside the vehicle, refer to
page 28.
1.Depress the brake pedal.2.Depress the clutch pedal.3.Press the Start/Stop button.
The ignition is activated automatically for a cer‐
tain time and is stopped as soon as the engine
starts.
Automatic transmission
Remote control in the ignition lock or, with
Comfort Access, inside the vehicle, refer to
page 28.
1.Depress the brake pedal.2.Move the selector lever to position P or N.3.Press the Start/Stop button.
The ignition is activated automatically for a cer‐
tain time and is stopped as soon as the engine
starts.
Seite 56ControlsDriving56
Online Edition for Part no. 01 40 2 911 475 - VI/13

Engine stop
General information Take the remote control with you
Take the remote control with you when
leaving the vehicle so that children, for exam‐
ple, cannot operate the windows and injure
themselves. ◀
Set the handbrake and further secure the
vehicle as required
Set the handbrake firmly when parking; other‐
wise, the vehicle may roll. On steep upward
and downward inclines, further secure the ve‐
hicle, for example, by turning the steering
wheel in the direction of the curb. ◀
Before driving into a car wash
To make it possible for the vehicle to roll in an
automatic car wash, follow the information on
Washing in automatic car washes, refer to
page 191.
Switching off the engine
Manual transmission1.With the vehicle at a standstill, press the
Start/Stop button.2.Shift into first gear or reverse.3.Set the handbrake firmly.4.Remove the remote control from the igni‐
tion lock.
Automatic transmission
1.Engage transmission position P with the ve‐
hicle stopped.2.Press the Start/Stop button.3.Set the handbrake firmly.4.Remove the remote control from the igni‐
tion lock.Handbrake
The concept
The handbrake is primarily intended to prevent
the vehicle from rolling while parked; it brakes
the rear wheels.
Also follow the instructions under Switching off
the engine, refer to page 57.
Setting
The lever engages automatically.
Releasing
Pull up slightly, press the button, and lower the
lever.
Notes Using the handbrake while driving
If it should become necessary to use the
handbrake while driving, do not pull the hand‐
brake too forcefully. Keep the button on the
handbrake lever pressed at all times.
Excessive application of the handbrake can
block the rear wheels and lead to fishtailing of
the vehicle. ◀
The brake lamps do not light up when the
handbrake is pulled.
Seite 57DrivingControls57
Online Edition for Part no. 01 40 2 911 475 - VI/13

Do not initialize the system when driving with
snow chains.1.Start the engine, but do not start driving.2.Press the button on the turn indicator lever
repeatedly until "SET/INFO" is displayed.3.Press and hold the button until the display
changes.4.Press the button repeatedly until the corre‐
sponding symbol and "RESET" are dis‐
played.5.Press and hold the button until the display
changes.6.Drive away.
Initialization is completed while the car is
traveling without feedback being given.
Indication of a flat tire
The warning lamps come on in yellow
and red. In addition, a signal sounds.
There is a flat tire or a major loss in tire inflation
pressure.1.Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneu‐
vers.2.Check whether the vehicle is fitted with
regular tires or run-flat tires.
Run-flat tires, refer to page 164, are la‐
beled with a circular symbol containing the
letters RSC marked on the tire sidewall.
Do not continue driving without run-flat
tires
Do not continue driving if the vehicle is not
equipped with run-flat tires; continued driving
may result in serious accidents. ◀
When a flat tire is indicated, DSC Dynamic Sta‐
bility Control is switched on if necessary.
Actions in the event of a flat tire
Normal tires
1.Identify the damaged tire.
Do this by checking the inflation pressure in
all four tires.
The tire pressure gauge of the Mobility Sys‐
tem, refer to page 165, can be used for this
purpose.
If the tire inflation pressure in all four tires is
correct, the Flat Tire Monitor may not have
been initialized. In this case, initialize the
system.
If an identification is not possible, please
contact the service center.2.Rectify the flat tire using the Mobility Sys‐
tem, refer to page 165, or replace the
damaged wheel, refer to page 181.
Run-flat tires
You can continue driving with a damaged tire
at speeds up to 50 mph/80 km/h.
Seite 84ControlsSafety84
Online Edition for Part no. 01 40 2 911 475 - VI/13

▷For a mounted wheel without TPM elec‐
tronics.▷When the TPM is disturbed by other sys‐
tems or devices with the same radio fre‐
quency.
Resetting the system
Reset the system after each correction of the
tire inflation pressure and after every tire or
wheel change.
1.Start the engine, but do not start driving.2.Press the button on the turn indicator lever
repeatedly until "SET/INFO" is displayed.3.Press and hold the button until the display
changes.4.Press the button repeatedly until the sym‐
bol for the Tire Pressure Monitor and "AC‐
TIVE" are displayed. The Tire Pressure Mon‐
itor can be reset with "RESET".5.Press and hold the button until "RESET‐
TING" is displayed.6.Drive away.
After driving a few minutes, the set inflation
pressures in the tires are accepted as the
target values to be monitored. The system
reset is completed during your drive, and
can be interrupted at any time. When driv‐
ing resumes, the reset is continued auto‐
matically. The indicator lamp goes out after
the system reset is completed.
Low tire pressure message
The warning lamps come on in yellow
and red. In addition, a signal sounds.
▷There is a flat tire or substantial loss of infla‐
tion pressure on the indicated wheel.▷The system was not reset after a wheel
change and thus issues warnings based on
the inflation pressures initialized last.1.Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneu‐
vers.2.Check whether the vehicle is fitted with
regular tires or run-flat tires.
Run-flat tires, refer to page 164, are la‐
beled with a circular symbol containing the
letters RSC marked on the tire sidewall.Seite 86ControlsSafety86
Online Edition for Part no. 01 40 2 911 475 - VI/13

12CauseHow to respondThe windshield washer fluid level is too
low.Add washer fluid, refer to page 61,
as soon as possible.Lights up in red:Service is due.Arrange a service appointment.
Check the service requirements, re‐
fer to page 173.Lights up in yellow:The engine will start the next time the
Start/Stop button is touched, possibly with‐
out the brake or clutch being depressedThe remote control is malfunctioning or, in
cars with Comfort Access, was not de‐
tected.The engine cannot be started. Have
the remote control checked, if nec‐
essary.The battery in the remote control is dis‐
charged.Use the remote control for a longer
journey or, in cars with Comfort Ac‐
cess, replace the battery.The belt tensioners and/or airbag system
has failed.Have the system checked immedi‐
ately.
Fasten the safety belts anyway.Steering assistance has failed.You can continue your journey, but
moderate your speed and exercise
due caution. Markedly different
steering response. Have the system
checked as soon as possible.Lights up in red:Engine malfunctionStop the car and switch off the en‐
gine. You cannot continue your jour‐
ney. Contact your service center.Lights up in yellow:Full engine power is no longer available.You can continue your journey, but
moderate your speed and exercise
due caution. Have the engine
checked as soon as possible.Seite 199Indicator/warning lampsMobility199
Online Edition for Part no. 01 40 2 911 475 - VI/13

Everything from A to ZIndexA
ABS, Antilock Brake Sys‐ tem 89
Acoustic signal, refer to Check Control 72
Activated charcoal filter with automatic climate con‐
trol 100
Adaptive Light Control 76
Additives, engine oil 171
Airbags 80
Airbags, indicator/warning light 82
Air circulation, refer to Recir‐ culated air mode 97, 99
Air conditioner 96
Air conditioning 96
Air conditioning mode– Air conditioner 96– Automatic climate con‐
trol 98
Air distribution
– Automatic 99– Individual 97– Manual 97, 100
Air drying, refer to Cooling
function 100
Air flow rate 96, 99
Air pressure, refer to Tire infla‐ tion pressure 154
Air supply
– Air conditioner 96– Automatic climate con‐
trol 98
Alarm system 31
Alarm system
– Avoiding unintentional
alarms 31– Interior motion sensor 31– Tilt alarm sensor 31
Always Open Timer 67
Ambient lighting 78
Antifreeze, washer fluid 61
Antilock Brake System, ABS 89
Anti-slip control, refer to Dy‐ namic Stability Control
DSC 89
Anti-theft protection 21
Approved engine oils 171
Ashtray 102
Assistance, roadside 186
Assistance when driving off, refer to Hill drive-off assis‐
tant 91
Assistance with starting en‐ gine, refer to Jump-start‐
ing 186
Automatic– Air distribution 99– Air flow rate 99
Automatic car wash 191
Automatic climate control
– Automatic air distribution 99
Automatic, cruise control 93
Automatic headlamp con‐ trol 74
Automatic rear spoiler 91
Automatic transmission with
Steptronic
– Kickdown 63– Overriding selector lever
lock 64
AUTO program with auto‐
matic climate control 99
AUX-IN port 132
Average fuel consumption 67
Average fuel consumption
– Setting the units 69
Average speed 67
Average speed, refer to Com‐ puter 66
B
Backrest curvature, refer to Lumbar support 45
Backrests, refer to Seats 44
Backup lamps, bulb replace‐ ment 179
Battery– Disposal 30– Remote control 20
Battery, refer to Vehicle bat‐
tery 184
Battery replacement
– Remote control 30
Belts, refer to Safety belts 46
Belt tensioners, refer to Safety belts 46
Bi-xenon headlamps 177
Blower, refer to Air flow rate 96, 99
Brake assistant 89
Brake discs, breaking in 112
Brake fluid, refer to Service re‐ quirements 70
Brake force distribution, elec‐ tronic 89
Brake pads, breaking in 112
Brakes
– Handbrake 57
Brakes, MINI maintenance
system 173
Brakes, service require‐ ments 70
Brake system, MINI mainte‐ nance system 173
Braking, notes 114
Breakdown assistance, Road‐ side Assistance 186
Breaking in 112
Button for starting the engine, refer to Start/Stop button 55
Seite 214ReferenceEverything from A to Z214
Online Edition for Part no. 01 40 2 911 475 - VI/13

Defroster– Rear window 97, 100
Defrosting windows 97
Defrost setting, refer to De‐ frosting windows 97
Dip stick, engine oil 170
Directional indicators, refer to Turn signals 58
Displacement, refer to Engine data 210
Display lighting, refer to In‐ strument lighting 77
Displays 14
Displays and controls 12
Displays, care 195
Displays, cleaning 195
Displays, refer to Instrument cluster 14
Disposal
– Remote control battery 30
Distance warning, refer to
Park Distance Control
PDC 94
Door key, refer to Remote
control with integrated
key 20
Door lock 25
Door lock, confirmation sig‐ nals 23
Doors, manual operation 25
Doors, unlocking and locking
– Confirmation signals 23– From the inside 25– From the outside 22
DOT Quality Grades 160
Drive-off assistant, refer to Hill drive-off assistant 91
Driving notes, breaking in 112
Driving off on hills, refer to Hill drive-off assistant 91
Driving stability control sys‐ tems 89
Driving tips, refer to Driving notes 112
Dry air, refer to Cooling func‐ tion 100
DSC Dynamic Stability Con‐
trol 89
DTC Dynamic Traction Con‐ trol 90
Dynamic Stability Control DSC 89
Dynamic Traction Control DTC 90
E Electrical convertible top 33
Electrical malfunction– Convertible top 35, 41– Door lock 25– Fuel filler flap 150– Tailgate 27
Electronic brake-force distri‐
bution 89
Electronic Stability Program ESP, refer to Dynamic Stabil‐
ity Control DSC 89
Emergency activation
– Automatic transmission, re‐
fer to Overriding selector
lever lock 64
Emergency activation, refer to
Manual activation
– Tailgate 27
Emergency operation, fuel
filler flap, unlocking man‐
ually 150
Emergency operation, refer to
Manual operation
– Convertible top 35, 41– Door lock 25
Energy, saving, refer to Saving
fuel 119
Engine, breaking in 112
Engine compartment 168
Engine oil, adding 170
Engine oil, additives, refer to Approved engine oils 171
Engine oil, alternative oil types 171
Engine oil change intervals,
refer to Service require‐
ments 70
Engine oil, dip stick 170
Engine oil, filling capacity 213
Engine oil, MINI maintenance system 173
Engine oil types, alterna‐ tive 171
Engine oil types, ap‐ proved 171
Engine, overheating, refer to Coolant temperature 66
Engine power, refer to Engine data 210
Engine, RPM 210
Engine start, assistance 186
Engine, starting 56
Engine, starting– Comfort Access 28
Engine, starting, Start/Stop
button 55
Engine, stopping, Start/Stop
button 55
Engine, switching off 57
ESP Electronic Stability Pro‐ gram, refer to Dynamic Sta‐
bility Control DSC 89
Exchanging wheels/tires 163
Exterior mirrors 48
Exterior mirrors, adjusting 48
Exterior mirrors, folding in and out 48
Exterior sensors, care 194
External temperature dis‐ play 65
External temperature display
– Changing the units 69– On the computer 69
External temperature warn‐
ing 65
Externel temperature dis‐ play 65
Seite 216ReferenceEverything from A to Z216
Online Edition for Part no. 01 40 2 911 475 - VI/13