MINI COOPER CONVERTIBLE 2018 Owners Manual

ter console. To do so, pull the retaining ringupward at the rear edge.2.Lift the sleeve. Unplug the cable connector,
if needed.3.Using the screwdriver from the onboard ve~ hicle tool kit, refer to page 231, press the
yellow release lever downward, see arrow.4.Press the button on the front of the selector
lever and move the selector lever back
slightly.
Release the release lever.5.Bring the selector lever into the desired po~
sition.
For additional information, see the chapter on tow-starting and towing.
Releasing
the
transmission
lock
electronically:
with
a
tap-operated
selector
lever
General
information Electronically unlock the transmission lock to
maneuver vehicle from a danger area.
Before unlocking the transmission lock, set the parking brake to prevent the vehicle from roll~ing away.
Engaging
selector
lever
position
N
Unlocking is possible, if the starter can spin the
engine.1.Press and hold down brake pedal.2.Press the Start/Stop button. The starter
must audibly start.3.Press the button on the selector lever, ar~
row 1, and press and hold the selector lever into selector lever position N, arrow N, until
selector lever position N is displayed in the
instrument cluster.
A Check Control message is displayed.4.Release the selector lever.5.Release brake, as soon as the starter stops.6.Maneuver the vehicle from the danger area
and secure it against moving on its own.
For additional information, see the chapter on tow-starting and towing.
Steptronic
Sport
transmission:
Launch
Control
Concept Launch Control enables optimum accelerationon surfaces with good traction under dry sur~ rounding conditions.
Seite 91DrivingCONTROLS91
Online Edition for Part no. 01402983394 - X/17

General
information
The use of Launch Control causes premature
component wear since this function represents a very heavy load for the vehicle.
Do not use Launch Control during the break-in,
refer to page 184, period.
To start with Launch Control do not steer the
steering wheel.
Functional
requirements Launch Control is available as soon as the en~
gine and transmission are at operating temper~ ature.
The engine is at operating temperature after an uninterrupted trip of at least 6 miles/10 km.
Depending on the external temperature and driving style, the transmission requires an unin~
terrupted trip of up to 30 miles/50 km in order
to reach the operating temperature required
for Launch Control.
Start
with
launch
control
While the engine is running:1. Press button and select SPORT with
the MINI Driving Modes switch.
The instrument cluster displays TRACTION
in combination with SPORT. The DSC OFF
indicator light lights up.2.Engage selector lever position S.3.With the left foot, forcefully press down on
the brake.4.Step on the accelerator pedal beyond the
resistance point at the full throttle position, kickdown.
A flag symbol is displayed in the instrument cluster.5.The starting engine speed adjusts. Within3 seconds, release the brake.Repeated
use
during
a
trip
After Launch Control has been used, the trans~
mission must cool down for approx. 5 minutes
before Launch Control can be used again.
After
using
Launch
Control
To increase vehicle stability, activate DSC Dy~
namic Stability Control again.
System
limits
An experienced driver may be able to achieve better acceleration values in DSC OFF mode.Seite 92CONTROLSDriving92
Online Edition for Part no. 01402983394 - X/17

DisplaysVehicle
features
and
op

Electronic
displays1Driver assistance systems
Messages, for instance Check Control
Timeps 98
External temperatureps 98
Selection listsps 102Total miles/trip odometerps 98
Onboard Computerps 1022Selector lever positionps 85
Gear shift indicatorps 1003MINI Driving Modes switch statusps 139Check
Control
Concept
The Check Control system monitors functions in
the vehicle and notifies you of malfunctions in
the monitored systems.
General
information
A Check Control message is displayed as a com~ bination of indicator or warning lights and SMS
text messages in the instrument cluster and in
the Head-up Display.
In addition, an acoustic signal may be output
and a SMS text message may appear on the
Control Display.Indicator/warning
lights
General
information
The indicator/warning lights can light up in a
variety of combinations and colors.
Several of the lights are checked for proper
functioning and light up temporarily when the engine is started or the ignition is switched on.
Red
lights Safety
belt
reminder Indicator light flashes or is illuminated:
safety belt on the driver or passenger side is not buckled. The safety belt re~
minder can also be activated if objects are placed on the front passenger seat.Seite 94CONTROLSDisplays94
Online Edition for Part no. 01402983394 - X/17

Make sure that the safety belts are positionedcorrectly.
Airbag
system Airbag system and belt tensioner are
not working.
Have the vehicle checked immediately
by a dealer

DSC
Dynamic
Stability
Control
is
deactivatedor
DTC
Dynamic
Traction
Control
is
activated
DSC is deactivated or DTC is activated.DSC, refer to page 137, and DTC, refer
to page 138.
Flat
Tire
Monitor
FTM The Flat Tire Monitor signals a loss of
tire inflation pressure in a tire.
Reduce your speed and stop cautiously.
Avoid sudden braking and steering maneuvers.
Flat Tire Monitor, refer to page 126.
Tire
Pressure
Monitor
TPM The indicator light lights up: the Tire
Pressure Monitor reports a low tire in~
flation pressure or a flat tire. Follow the
information in the Check Control message.
The indicator light flashes and then continu~ ously lights up: no flat tire or loss of tire infla~
tion pressure can be detected.'

Front
fog
lightsFront fog lights are switched on.
Front fog lights, refer to page 114.
High-beam
Assistant High-beam Assistant is switched on.
High beams are switched on and off au~
tomatically depending on the traffic sit~
uation.
High-beam Assistant, refer to page 113.
Cruise
control The system is switched on. It maintains
the speed that was set using the control
elements on the steering wheel.
Blue
lights
High
beams High beams are switched on.High beams, refer to page 78.
Hiding
Check
Control
messages
Press and hold button on signal lever.
Continuous
display
Some Check Control messages are displayed
continuously and are not cleared until the mal~ function is eliminated. If several malfunctionsoccur at once, the messages are displayed con~
secutively.
The messages can be hidden for approx. 8 sec~
onds. After this time, they are displayed again
automatically.
Temporary
display
Some Check Control messages are hidden auto~ matically after approx. 20 seconds. The CheckControl messages are stored and can be dis~
played again later.
Displaying
stored
Check
Control
messages
Via the Central Information Display (CID):1. "Vehicle info"2."Vehicle status"3. "Check Control"4.Select the SMS text message.
Display
Check
Control At least one Check Control message isdisplayed or is stored.
SMS
text
messages
SMS text messages in combination with a sym~
bol in the instrument cluster explain a Check
Control message and the meaning of the indi~
cator/warning lights.
Supplementary
SMS
text
messages
Additional information, such as on the cause of an error or the required action, can be called upvia Check Control.
With urgent messages the added text will be
automatically displayed on the Control Display.
Symbols
Within the supplementary text, the following functions can be selected independent of the check control message.
Seite 97DisplaysCONTROLS97
Online Edition for Part no. 01402983394 - X/17

'

DateThe date is displayed in the in~
strument cluster.
The date can be set via the Cen~
tral Information Display (CID).
Range
Safety
information NOTE
With a driving range of less than
30 miles/50 km the engine may no longer have sufficient fuel. Engine functions are not ensuredanymore. There is a risk of damage to property.Refuel promptly. '

Required maintenance procedures and le~gally mandated inspections are displayed.4.Select an entry to call up detailed informa~
tion.
Symbols
SymbolsDescriptionNo service is currently required.The deadline for scheduled
maintenance or a legally man~
dated inspection is approach~
ing.The service deadline has al~
ready passed.
Entering
appointment
dates
Enter the dates for the mandatory vehicle in~
spections.
Make sure that the vehicle's date and time are
set correctly.
Via the Central Information Display (CID):
1. "Vehicle info"2."Vehicle status"3. "Service required"4."g Vehicle inspection"5."Date:"6.Adjust the settings.7.Confirm.
The entered date is stored.
Gear
shift
indicator
Concept The system recommends the most fuel efficient
gear for the current driving situation.
General
information
Depending on the vehicle's features and coun~
try-specific version, the gear shift indicator is active in the manual mode of the Steptronic
transmission and with manual transmission.
Suggestions to shift gear up or down are dis~
played in the instrument cluster.
Manual
transmission:
displayingExampleDescriptionFuel efficient gear is set.Shift into fuel efficient gear.
Steptronic
transmission:
displaying
ExampleDescriptionFuel efficient gear is set.Shift into fuel efficient gear.
Speed
Limit
Info
Speed
Limit
Info
Concept Speed Limit Info shows the current maximum
permitted speed in the instrument cluster.
General
information The camera at the base of the interior mirrordetects traffic signs at the edge of the road aswell as variable overhead sign posts. Traffic
signs with extra symbols for wet road condi~
tions, etc., are also detected and compared with the vehicle's onboard data, such as from
Seite 100CONTROLSDisplays100
Online Edition for Part no. 01402983394 - X/17