MINI COOPER CONVERTIBLE 2018 Service Manual

3.Slide the integrated key in the cover of the
battery compartment and raise the cover.4.Push battery in the direction of the arrow
using a pointed object and lift it out.5.Insert a type CR 2032 battery with the posi~
tive side facing up.6.Insert lid and cover.7.Push the integrated key into the remote
control until it engages.
Have old batteries disposed of by a
dealer

It is not possible to switch on the drive-ready
state if the remote control has not been de~
tected.
Proceed as follows in this case:1.Hold the remote control as shown against the marked area on the steering column.
Pay attention to the display in the instru~ ment cluster.2.If the remote control is detected:
Start the engine within 10 seconds.
If the remote control is not detected, slightly change the position of the remote control and
repeat the procedure.
Integrated
key
General
information The driver's door can be locked and unlocked
without remote control using the integrated key.
The integrated key can also be used for the glove compartment on the front passenger
side.
Safety
information WARNING
Unlocking from the inside is only possible
with special knowledge.
Persons who spend a lengthy time in the vehi~
cle while being exposed to extreme tempera~ tures are at risk of injury or death. Do not lock
the vehicle from the outside when there are
people in it. '

detection of the remote control, refer topage 41.
Buttons
for
the
central
locking
system
General
information In the event of a severe accident, the vehicle is
automatically unlocked. The hazard warning system and interior lights come on.
Overview
Buttons for the central locking system.
Locking Press the button with the doors closed.
'

other vehicle access points. Rather, the vehicleis locked again.
If a door of a locked vehicle was opened from
the inside via the door opener, pressing the
button on the outer door handle first locks the vehicle again. To unlock, the button on the
outer door handle must be pressed again.
This is the case whether the vehicle was locked
automatically after driving off or via the central locking system button from the inside.
Locking
On the driver's or front passenger's outer doorhandle, press the button.
Convenient
closing
Safety
information WARNING
With convenient closing, body parts can
be jammed. There is a risk of injury. Make sure
that the area of movement of the doors is clear
during convenient closing. '

Opening
Press button on the exterior of the tailgate.
Malfunction Remote control detection by the vehicle maymalfunction under the following circumstances:
'

Opening
from
the
insideWith the vehicle stationary, press the
button in the driver's floor area.
Closing
To close the tailgate, swivel it upwards and
press it closed.
Trunk
emergency
unlocking
Pull the handle inside the cargo area.The tailgate unlocks.
Personal
Profile
Concept
Via Personal Profiles, individual settings for sev~
eral drivers can be stored and called up again when required.
General
information
There are three driver profiles with which per~ sonal vehicle settings can be stored. Every re~
mote control has one of these driver profiles
assigned.
If the vehicle is unlocked using a remote con~ trol, the assigned personal driver profile will be
activated. All settings stored in the driver profile
are automatically applied.
If several drivers use their own remote control,
the vehicle will adjust the personal settings dur~
ing unlocking. These settings are also restored,
if the vehicle has been used in the meantime by a person with a different remote control.
Changes to the settings are automatically
stored in the driver profile currently activated.
If another driver profile is selected via the Cen~ tral Information Display (CID), the settingsstored in it will be applied automatically. The
new driver profile is assigned to the remote
control currently used.
There is an additional guest profile available that is not assigned to any remote control: it
can be used to apply settings in the vehicle
without changing the personal driver profiles.
Functional
requirements
For the system to be able to identify the driver
profile associated to a particular driver, the de~
tected remote control must be clearly allocated
to the driver.
This is the case when:'

'

Via the Central Information Display (CID):1. "Settings"2."Profiles"3."Import profile"4."USB device"
Display
profile
list
during
start
The profile list can be displayed during each start to select the desired profile.
Via the Central Information Display (CID):
1. "Settings"2."Profiles"3.Open "Options".4."Display user list at startup"
System
limits
A clear assignment between the remote control and driver may not be possible in the following
cases, for example.
'

The vehicle locks automatically after a
short period of time if no door is
opened after unlocking.'

'