seat MITSUBISHI 380 2005 Service Manual

FRONT SEAT ASSEMBLY
INTERIOR52A-36
DISASSEMBLY STEPS
<<A>>HEADREST
1. HINGE COVER
2. INNER SEAT BELT
3. MANUAL RECLINER ADJUSTER
(VEHICLES WITH MANUAL
RECLINER)
4. SIDE SHIELD COVER
5. POWER RECLINER ADJUSTER
(VEHICLES WITH POWER
RECLINER)
6. SEAT HEIGHT ADJUSTER
KNOB
7. MAIN POWER SWITCH
8. LUMBAR POWER SWITCH
(VEHICLES WITH POWER
RECLINER)
9. MEMORY BUTTON MODULE
(VEHICLES WITH MEMORY
SEATS)
10. SIDE SHIELD MOUNT BRACKET
11. FRONT SEAT BACK ASSEMBLY
12. CUSHION ASSEMBLY13. SEAT CUSHION COVER
14. SEAT CUSHION PAD
15. SEAT CUSHION FRAME
16. SEAT BACK PANEL
17. SIDE AIRBAG MODULE
<<B>>18. HEADREST GUIDE
19. MANUAL LUMBAR ADJUSTER
HANDLE
<<C>>20. SEAT BACK COVER
21. SEAT BACK PAD
22. LUMBAR ASSEMBLY
23. RECLINER LEVER RETURN
SPRING
24. RECLINER LEVER SHAFT
25. SEAT BACK PATCH HARNESS
(VEHICLES FITTED WITH
POWER SEAT BACK)
26. SEAT BACK FRAME
27. SEAT POWER HARNESS
28. SEAT SLIDE ADJUSTERDISASSEMBLY STEPS

FRONT SEAT ASSEMBLY
INTERIOR52A-37
<LH SIDE>

FRONT SEAT ASSEMBLY
INTERIOR52A-38

FRONT SEAT ASSEMBLY
INTERIOR52A-39

FRONT SEAT ASSEMBLY
INTERIOR52A-40

FRONT SEAT ASSEMBLY
INTERIOR52A-41
REMOVAL STEPS
<<A>>HEADREST
1. HINGE COVER
2. INNER SEAT BELT
3. MANUAL RECLINER ADJUSTER
HANDLE (VEHICLES WITH
MANUAL RECLINER)
4. SIDE SHIELD COVER
5. FORE AFT ADJUSTER KNOB
6. MAIN POWER SWITCH
7. SIDE SHIELD MOUNT BRACKET
8. FRONT SEAT BACK ASSEMBLY
9. CUSHION ASSEMBLY
10. SEAT CUSHION COVER
11. SEAT CUSHION PAD
12. SEAT CUSHION FRAME13. SEATBACK PANEL
14. SIDE AIRBAG MODULE
<<B>>
15. HEADREST GUIDE
16 MANUAL LUMBAR ADJUSTER
HANDLE
<<C>>
17. SEATBACK COVER
18. SEATBACK PAD
19. LUMBAR ASSEMBLY
20. RECLINER LEVER RETURN
SPRING
21. RECLINER LEVER SHAFT
22. SEAT BACK FRAME
23. SEAT POWER HARNESS
24. SEAT SLIDE ADJUSTERREMOVAL STEPS (Continued)

FRONT SEAT ASSEMBLY
INTERIOR52A-42
REMOVAL SERVICE POINT
.
<<A>> HEADREST REMOVAL
1. Raise the head restraint fully.
2. Insert a probe that is suited to fit into the hole (1) in the right
hand head restraint sleeve (2) as illustrated in the figure
below.
3. Whilst the probe is inserted slightly, apply slight pressure on
the head restraint. Apply and hold pressure upwards.
4. To remove the head restraint, you must depress the sleeve
height adjuster lock (3) on the left-hand head restraint
sleeve as illustrated below.
<<B>> HEADREST SLEEVE REMOVAL
1. To reveal upper portion of the seat back frame or
active head restraint frame (1) as shown in figure
below, push down on the surrounding seat cover.
2. By using a small flat blade screwdriver, depress
the sleeve locking tab (2), and remove the head
restaint sleeve (3) in upwards movement from the
frame as illustrated below.
3. If required, repeat process for the remaining
sleeve.
<<C>> SEAT BACK PANEL REMOVAL
AND FITMENT
1. Move front seat to the most forward position.
2. Pull the lower edge of seat panel towards you, as
shown below (1).
3. Slide the panel downwards (2) as the top section
is held in by 2 locating hooks (lugs).
4. Upon fitment, be sure to firstly locate the top 2
lugs into position (2), as shown above.
5. Approximately square up panel to the seat, so by
doing this you will be able to locate the bottom 2
clips to press in the panel (1), as shown above.

FRONT SEAT TRIM COVER
INTERIOR52A-43
FRONT SEAT TRIM COVER
REMOVAL AND FITMENT
REMOVAL
.
1. Remove seat from vehicle and cushion or seat back
assembly as required. Remove all seat plastic covers etc.
2. Unclip all the plastic retainer clips at the rear of the trim
cover. This is typical for the cushion and the back of the
seat.
3. Peel cover away from the foam pad.
NOTE: Place a finger on the Blue Velcro strip when peeling
the cover to prevent the strip being pulled out of the foam
pad.

FRONT SEAT TRIM COVER
INTERIOR52A-44
FITMENT
.
1. Locate the new trim onto the pad by aligning the Velcro strip
with the grooves. Use an intersection in order to align both
directions. Whenever possible work from the centre of the
trim toward the outside.
2. Push the Velcro strips into place along all the grooves.

FRONT SEAT TRIM COVER
INTERIOR52A-45
3. Pull the cover over the outside of the pad and reattach the
retaining clips where required.
NOTE: It may be necessary to make some adjustment and
work the cover into position to remove creases. Reassemble
seat and fit to vehicle.