headrest MITSUBISHI 380 2005 Workshop Manual

FRONT SEAT ASSEMBLY
INTERIOR52A-21
FRONT SEAT ASSEMBLY
REMOVAL AND INSTALLATIONM1522001300560
Before removing the front seat assembly, refer to GROUP 52B, Service Precautions
P.52B-16 and Air Bag Module and Clock Spring P.52B-237.
2. HEADREST
FRONT SEAT ASSEMBLY
REMOVAL STEPS
3. SEAT BELT SWITCH
CONNECTOR
4. POWER SEAT CONNECTOR RH
<VEHICLES WITH MEMORY
SEAT>
6. POWER SEAT CONNECTOR
<VEHICLES WITH POWER SEAT>7. SIDE-AIR BAG MODULE
CONNECTOR <VEHICLES WITH
SIDE-AIR BAG>
8. FRONT SEAT REAR ANCHOR
COVER
>>A<<10. FRONT SEAT ASSEMBLYFRONT SEAT ASSEMBLY
REMOVAL STEPS (Continued)

FRONT SEAT ASSEMBLY
INTERIOR52A-36
DISASSEMBLY STEPS
<<A>>HEADREST
1. HINGE COVER
2. INNER SEAT BELT
3. MANUAL RECLINER ADJUSTER
(VEHICLES WITH MANUAL
RECLINER)
4. SIDE SHIELD COVER
5. POWER RECLINER ADJUSTER
(VEHICLES WITH POWER
RECLINER)
6. SEAT HEIGHT ADJUSTER
KNOB
7. MAIN POWER SWITCH
8. LUMBAR POWER SWITCH
(VEHICLES WITH POWER
RECLINER)
9. MEMORY BUTTON MODULE
(VEHICLES WITH MEMORY
SEATS)
10. SIDE SHIELD MOUNT BRACKET
11. FRONT SEAT BACK ASSEMBLY
12. CUSHION ASSEMBLY13. SEAT CUSHION COVER
14. SEAT CUSHION PAD
15. SEAT CUSHION FRAME
16. SEAT BACK PANEL
17. SIDE AIRBAG MODULE
<<B>>18. HEADREST GUIDE
19. MANUAL LUMBAR ADJUSTER
HANDLE
<<C>>20. SEAT BACK COVER
21. SEAT BACK PAD
22. LUMBAR ASSEMBLY
23. RECLINER LEVER RETURN
SPRING
24. RECLINER LEVER SHAFT
25. SEAT BACK PATCH HARNESS
(VEHICLES FITTED WITH
POWER SEAT BACK)
26. SEAT BACK FRAME
27. SEAT POWER HARNESS
28. SEAT SLIDE ADJUSTERDISASSEMBLY STEPS

FRONT SEAT ASSEMBLY
INTERIOR52A-41
REMOVAL STEPS
<<A>>HEADREST
1. HINGE COVER
2. INNER SEAT BELT
3. MANUAL RECLINER ADJUSTER
HANDLE (VEHICLES WITH
MANUAL RECLINER)
4. SIDE SHIELD COVER
5. FORE AFT ADJUSTER KNOB
6. MAIN POWER SWITCH
7. SIDE SHIELD MOUNT BRACKET
8. FRONT SEAT BACK ASSEMBLY
9. CUSHION ASSEMBLY
10. SEAT CUSHION COVER
11. SEAT CUSHION PAD
12. SEAT CUSHION FRAME13. SEATBACK PANEL
14. SIDE AIRBAG MODULE
<<B>>
15. HEADREST GUIDE
16 MANUAL LUMBAR ADJUSTER
HANDLE
<<C>>
17. SEATBACK COVER
18. SEATBACK PAD
19. LUMBAR ASSEMBLY
20. RECLINER LEVER RETURN
SPRING
21. RECLINER LEVER SHAFT
22. SEAT BACK FRAME
23. SEAT POWER HARNESS
24. SEAT SLIDE ADJUSTERREMOVAL STEPS (Continued)

FRONT SEAT ASSEMBLY
INTERIOR52A-42
REMOVAL SERVICE POINT
.
<<A>> HEADREST REMOVAL
1. Raise the head restraint fully.
2. Insert a probe that is suited to fit into the hole (1) in the right
hand head restraint sleeve (2) as illustrated in the figure
below.
3. Whilst the probe is inserted slightly, apply slight pressure on
the head restraint. Apply and hold pressure upwards.
4. To remove the head restraint, you must depress the sleeve
height adjuster lock (3) on the left-hand head restraint
sleeve as illustrated below.
<<B>> HEADREST SLEEVE REMOVAL
1. To reveal upper portion of the seat back frame or
active head restraint frame (1) as shown in figure
below, push down on the surrounding seat cover.
2. By using a small flat blade screwdriver, depress
the sleeve locking tab (2), and remove the head
restaint sleeve (3) in upwards movement from the
frame as illustrated below.
3. If required, repeat process for the remaining
sleeve.
<<C>> SEAT BACK PANEL REMOVAL
AND FITMENT
1. Move front seat to the most forward position.
2. Pull the lower edge of seat panel towards you, as
shown below (1).
3. Slide the panel downwards (2) as the top section
is held in by 2 locating hooks (lugs).
4. Upon fitment, be sure to firstly locate the top 2
lugs into position (2), as shown above.
5. Approximately square up panel to the seat, so by
doing this you will be able to locate the bottom 2
clips to press in the panel (1), as shown above.