MITSUBISHI ASX 2019 Owner's Manual (in English)

Service reminder
When the time for periodic inspection ar-rives, the warning display is displayed for a
few seconds after the ignition switch or the operation mode ON screen. Refer to “Service
reminder” on page 5-16.
Type 1
Type 2
Drive mode indicator display
screen*Type 1Type 2
This displays the 4WD status.
If you select “4WD LOCK” mode with the drive mode selector, “4WD LOCK” is dis-played; if you select “4WD AUTO” mode,
“4WD” is displayed.
Nothing is displayed when 2WD mode is se- lected. Refer to “Drive mode-selector” on
page 6-27. mark display screen (when
the ignition switch or the oper- ation mode is ON)
This is displayed when you press the multi-informationmeter switch and switch the
warning display screen. This mark is also displayed
if there is another warning
other than the one displayed.
When the cause of the warning display is eliminated, the
mark goes out automatical-
ly.
NOTEz When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-05.
Refer to “Information screen (when the igni- tion switch or the operation mode is ON)”
on page 5-10
Multi-information display
5-092*$((Instruments and controls5

Information screen (when theignition switch or the operation mode is ON)
Each time you lightly press the multi-infor- mation meter switch, the display screenswitches in the following order.
Type 1Type 2When there is no warning displayWhen there is no warning displayWhen there is a
warning displayWhen there is a
warning display
1- Odometer (Type1)/Tripmeter
2- Odometer (Type1)/Tripmeter
3- Service reminder
4- Engine coolant temperature display
(Type 1)
5- Driving range display (Type 1)
6- Average speed display, average fuel con-
sumption display, momentary fuel con- sumption display (Type 1)
7- Driving range display, momentary fuel
consumption display (Type 2)
8- Average fuel consumption display, mo-
mentary fuel consumption display (Type
2)
9- Average speed display, momentary fuel
consumption display (Type 2)
10- Function setting screen 11- Redisplay of a warning display screenNOTEz While driving, even if you operate the multi-
information meter switch, the function set- ting screen is not displayed. Always stop thevehicle in a safe place before operating.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-18.
z When there is information to be announced,
such as a system fault, the buzzer soundsand the screen display is switched.
Refer to “Interrupt display screen (when the
ignition switch or the operation mode is ON)” on page 5-14.Odometer/Tripmeter
The operation method is the same as when
the ignition switch or the operation mode is OFF.
Refer to “Odometer/Tripmeter” for further details on page 5-06.
Multi-information display
5-102*$((Instruments and controls5 Type 1Type 2

Service reminder
This displays the distance
and number of months until the next periodic inspection.
Refer to “Service reminder”
on page 5-16.
Type 2Type 1Engine coolant temperature
display
This indicates the engine coolant temperature.If the coolant becomes hot,
“
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUT,ONz If the engine is overheating, “” will blink.
In this case, the bar graph is on the red zone.
lmmediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-04.Driving range display
This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below approximately 50 km (30 miles), “---” is dis-
played.
Refuel as soon as possible.NOTEz The driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
z When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
z On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is due to the movement of fuel in the tank and
does not indicate a malfunction.
Multi-information display
5-112*$((Instruments and controls5 Type 1Type 2 Type 1 Type 2

NOTEzThe display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-18.Average speed display
This displays the average speed from the last
reset to the present time.
There are the following 2 mode settings.
For the method for changing the average
speed display setting, refer to “Changing the
function settings (when the ignition switch or the operation mode is ON)” on page 5-18.
Manual reset mode
z When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed displayed at that time is reset.
z When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system@
Turn the ignition switch from the “ACC”
or “LOCK” position to the “ON” posi- tion.
[For vehicles equipped with keyless op-
eration system@
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done, however, the data from the last reset isdisplayed.
Auto reset mode z When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed
displayed at that time is reset.z When the engine switch or the operation
mode is in the following conditions, the
average speed display is automatically
reset.
[Except for vehicles equipped with key-
less operation system@
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or longer.NOTEz The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
z “---” is displayed when the average speed
cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings (when the ignition switch is “ON”)” on page
5-18.
z The memory of the auto reset mode or man-
ual reset mode for the average speed display is erased if the battery is disconnected.Average fuel consumption dis-
play
This displays the average fuel consumption
from the last reset to the present time.
There are the following 2 mode settings.
Multi-information display
5-122*$((Instruments and controls5 Type 1 Type 2

For information on how to change the aver-age fuel consumption display setting, refer to
“Changing the function settings (when the ig- nition switch or the operation mode is ON)”
on page 5-18.

The “” mark (A) in the momentary fuel
gauge shows the average fuel consumption. (Type 2)

Manual reset mode
z When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the
average fuel consumption displayed at that time is reset.
z When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system@
Turn the ignition switch from the “ACC”
or “LOCK” position to the “ON” posi- tion.
[For vehicles equipped with keyless op-
eration system@
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done, however, the data from the last reset isdisplayed.
Auto reset mode
z When the average fuel consumption is
being displayed, if you hold down the
multi-information meter switch, the average fuel consumption displayed atthat time is reset.
z When the engine switch or the operation
mode is in the following conditions, the
average fuel consumption display is au- tomatically reset.
[Except vehicles equipped with keyless
operation system@
The ignition switch is in the “ACC” or
“LOCK” position for about 4 hours or
longer.
[For vehicles equipped with keyless op- eration system@
The operation mode is in ACC or OFF
for about 4 hours or longer.NOTEz The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con-
sumption may vary from the actual fuel con- sumption. Treat the fuel consumption dis-played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-
sumption display is erased if the battery is disconnected.
Multi-information display
5-132*$((Instruments and controls5Type 1 Type 2

NOTEzThe display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km`.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-18.Momentary fuel consumption
display
While driving, this displays the momentary fuel consumption, using a bar graph.
When the value of momentary fuel consump-tion surpasses the value of average fuel con-
sumption, the momentary fuel consumption
is displayed with a white bar graph. (Type 2)
Be conscious of maintaining the value of mo-
mentary fuel consumption below the value ofaverage fuel consumption, driving with the
bet-ter fuel consumption can be possible.NOTEz When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.
z The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km`.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-18.
z It is possible to cancel the green bar graph.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-18.Function setting screen
The “Display language”,
“Temperature unit”, “Fuel consumption unit”, and
“Average fuel consumption
and speed reset method” etc. settings can be modified as
desired.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-18 for further de-
tails.
Interrupt display screen (when
the ignition switch or the oper- ation mode is ON)
Warning display
When there is information to be announced, such as a system fault, a sound is emitted and
the information screen switches to the warn- ing display screen.
Refer to the warning list and take the neces-
sary measures.
Refer to “Warning display list (when the igni-
tion switch or the operation mode is ON)” on page 5-31.
When the cause of the warning display is eliminated, the warning display goes out au-tomatically.
To return to the screen displayed before
the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen
that was displayed before the warning dis-
play.

Multi-information display
5-142*$((Instruments and controls5 Type 2Type 1

If you press the multi-information meter
switch, the display screen switches to the screen that was displayed before the warning
display and the
mark (A) is displayed.
NOTEz Warning display screens with a “” or “”
mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi-informa-
tion meter switch as follows.
“
”: Press lightly.
“
”: Press for about 2 seconds or more.
Redisplay of a warning display
screen
When the mark is displayed, if you lightly
press the multi-information meter switch a
few times, the warning display screen you switched from is displayed again.
Other interrupt displays
The operation status of each system is dis- played on the information screen.
Refer to the appropriate page in the warning
display list for further details.
Refer to “Other interrupt displays” on page 5-42.
Selector lever position display
screen*
Shows the position of the se- lector lever.
Refer to “Selector lever op- eration” on page 6-20.
Outside temperature display
screen
This shows the temperature
outside the vehicle.
NOTEz The display setting can be changed to the
preferred units (

NOTEzIt may take several seconds to stabilise the
display after refilling the tank.
z If fuel is added with the ignition switch or
the operation mode is in ON, the fuel gauge may incorrectly indicate the fuel level.Fuel lid mark
The arrow (A) indicates that the fuel tank fill-
er is located on the left side of the body.
Fuel remaining warning display
When the fuel is reduced to about 10 litres,the information screen switches to the inter-
rupt display of the fuel remaining warning display, and the “
” mark (B) on the fuel re-
maining display flashes slowly (about once per second).
After a few seconds, the information screen returns from the fuel remaining warning dis-
play to the previous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “
” mark
(B) on the fuel remaining display flashes
quickly (about twice per second).
NOTEz On inclines or curves, the display may be in-
correct due to the movement of fuel in the
tank.Service reminder
Displays the approximate time until the next
periodic inspection recommended by
MITSUBISHI MOTORS . “---” is displayed
when the inspection time has arrived.
NOTEz Depending on the vehicle specifications, the
displayed time until the next periodic inspec-
tion may differ from that recommended by
MITSUBISHI MOTORS.
In addition, the display settings for the next periodic inspection time can be modified.
To modify the display settings, have it adjus- ted at a MITSUBISHI MOTORS Authorized
Service Point.
For more details, consult a MITSUBISHI
MOTORS Authorized Service Point.Type 1Type 2
1. Displays the time until the next periodic
inspection.
Multi-information display
5-162*$((Instruments and controls5 Type 1
Type 2

NOTEzThe distance is shown in units of 100 km
(100 miles). The time is shown in units of months.
2. This informs you that a periodic inspec-
tion is due. We recommend you to con-
sult a MITSUBISHI MOTORS Author-
ized Service Point.

At that time, when the ignition switch is switched from the “LOCK” position to
the “ON” position or the operation mode
is changed from OFF to ON, the warn- ing display is displayed for a few sec-onds on the information screen.
Type 1
Type 2
3. After your vehicle is inspected at a
MITSUBISHI MOTORS Authorized
Service Point, it displays the time until the next periodic inspection.
To reset
The “---” display can be reset while the igni- tion switch or the opertion mode is in OFF.When the display is reset, the time until the
next periodic inspection is displayed and the warning display is no longer displayed when
the ignition switch is turned from the
“LOCK” position to the “ON” position or the operation mode is changed from OFF to ON.
1. When you lightly press the multi-infor-
mation meter switch a few times, the in-
formation screen switches to the service
reminder display screen.Type 1Type 2
2. Press and hold the multi-information
meter switch for about 2 seconds or more to display “
” and make it flash.
(If there is no operation for about 10 sec-
onds with flashing, the display returns to the previous screen.)
Multi-information display
5-172*$((Instruments and controls5

3.Lightly press the multi-information me-
ter switch while the icon is flashing to
change the display from “---” to “CLEAR”. After this, the time until the
next periodic inspection will be dis- played.Type 1Type 2
CAUT,ONz The customer is responsible for making sure
that periodic inspection and maintenance are
performed. Inspections and maintenance must be performed to prevent accidents and malfunctions.NOTEz “---”display cannot be reset when the igni-
tion switch or the operation mode is in ON.
z When “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri-
odic inspection is displayed.
z If you accidentally reset the display, we rec-
ommend you to consult a MITSUBISHI
MOTORS Authorized Service Point.Door ajar warning display
screen (when the ignition switch or the operation mode isON)Type 1
Type 2
If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or
tailgate.
If the vehicle speed exceeds approximately
8 km/h (5 mph) while a door is ajar, a buzzer
sounds 4 times. This notifies the driver that a
door is ajar.CAUT,ONz Before moving your vehicle, check that the
warning lamp is OFF.Changing the function settings
(when the ignition switch or theoperation mode is ON)
1. Stop the vehicle in a safe place. Firmly apply the parking brake and putthe gearshift lever into the “N” (Neutral)
position ( M/T) or the selector lever into
the “P” (Park) position (CVT).
2. Lightly press the multi-information me-
ter switch a few times to switch the in- formation screen to the function setting
screen.
Multi-information display
5-182*$((Instruments and controls5