MITSUBISHI ASX 2019 Owner's Manual (in English)

Screen type 1Screen type 2CauseSolution (Reference)
—
(flashing in yellow)
zThe Lane Departure Warning
(LDW) has detected that your
vehicle is about to leave or has left the lane.Refer to “Lane Departure Warning
(LDW)” on page 6-61.
—
z There is a fault in the Lane
Departure Warning (LDW).z We recommend you to have it
checked. Refer to “LDW de- activation due to fault” on
page 6-63.
—
z The Blind Spot Warning
(BSW) sensor is temporarily
not available for some reason
such as the environmental condition or increase of the
sensor temperature.z When the warning display
does not disappear after wait- ing for a while, contact a
MITSUBISHI MOTORS Au-
thorized Service Point.
Refer to “When the sensor is temporarily not available” on
page 6-58.
—
z The Blind Spot Warning
(BSW) does not operate nor-
mally because there are some malfunctions in the sensor or
the system.z We recommend you to have it
checked, immediately.
Refer to “When there is a
malfunction in the system or
the sensor” on page 6-58.
Indication lamp, warning lamp, and information screen display list
5-392*$((Instruments and controls5

Screen type 1Screen type 2CauseSolution (Reference)
—
zForeign objects, such as dirt,
snow or ice, adhere to the bumper surface around thesensor.z Remove a foreign object on
the bumper surface around the
sensor.
When the warning display does not disappear after hav- ing cleaned the bumper sur-
face around the sensor, con- tact a MITSUBISHI
MOTORS Authorized Service
Point.
Refer to “Blind Spot Warning
(BSW): When there is a for- eign object on the sensor” on
page 6-58.
—
(flashing in yellow)
z The Rear Cross Traffic Alert
(RCTA) has detected a vehi-
cle that is approaching your
vehicle.z Pay special attention to the
rear of your vehicle.
Refer to “Rear Cross Traffic Alert (RCTA)*” on page6-59.
Indication lamp, warning lamp, and information screen display list
5-402*$((Instruments and controls5

Screen type 1Screen type 2CauseSolution (Reference)
—
zThere is a fault in the sensor.zWe recommend you to con-
sult a MITSUBISHI
MOTORS Authorized Service
Point.
Refer to “Forward Collision Mitigation system (FCM):System problem warning” on
page 6-52.
Refer to “Lane Departure Warning (LDW): Systemproblem warning” on page
6-63.
—
z The Forward Collision Miti-
gation system (FCM) and
Lane Departure Warning (LDW) is temporarily un-available due to the high or
low temperature of the sensor.z After the temperature of the
sensor has been in range, the system will automatically re-
turn to operation.
Refer to “Forward Collision Mitigation system (FCM):System problem warning” on page 6-52.
Refer to “Lane Departure Warning (LDW): System
problem warning” on page 6-63.
—
z The sensor is temporarily un-
available due to conditionssuch as the adhesion of con-
taminants to the sensor or windscreen.
This is not a malfunction.Refer to “Forward Collision Miti-
gation system (FCM): System
problem warning” on page 6-52.
Refer to “Lane Departure Warning
(LDW): System problem warning”
on page 6-63.
Indication lamp, warning lamp, and information screen display list
5-412*$((Instruments and controls5

Screen type 1Screen type 2CauseSolution (Reference)
—
zThere is a fault in the Auto-
matic High-Beam (AHB) sys- tem.z We recommend you to con-
sult a MITSUBISHI
MOTORS Authorized Service
Point.
Refer to “System problem
warning” on page 5-55.

Other interrupt displaysScreen type 1Screen type 2System operation statusReference
––
z When starting the engine, you
pressed the engine switch without depressing the clutch pedal (M/T).z On vehicles with
M/T, place
the gearshift lever in the “N” (Neutral) position, fully de- press the clutch pedal, depressthe brake pedal with the rightfoot. Then, press the engine
switch. Refer to “Starting and stopping the engine” on page
3-17.
––
z When starting the engine, the
selector lever is in a position
other than the “P” (Park) or the “N” (Neutral) position, or you pressed the engine switch
without depressing the brake pedal (A/T or CVT).z On vehicles with A/T or CVT,
place the selector lever in the “P” (PARK) position, depress
the brake pedal with the right
foot. Then, press the engine switch. Refer to “Starting and stopping the engine” on page
3-17.

The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details.
Indication lamp, warning lamp, and information screen display list
5-422*$((Instruments and controls5

NOTEzWhen operating each system, confirm that the operation status of the system has changed on the information screen. However, the operation status of the
system may not be displayed immediately after the warning display appears even if the system is operated.Screen type 1Screen type 2System operation statusReferencez When “2WD” mode is selec-
ted with the drive mode selec-torz Refer to “Electronically con-
trolled 4WD system” on page
6-27.z When “4WD AUTO” mode is
selected with the drive mode selectorz When “4WD LOCK” mode is
selected with the drive mode selectorz When the Active Stability
Control (ASC) is operatingz Refer to “Active Stability
Control (ASC)” on page
6-39.
Indication lamp, warning lamp, and information screen display list
5-432*$((Instruments and controls5

Screen type 1Screen type 2System operation statusReference—zWhen the Forward Collision
Mitigation system (FCM) is
activated or the timing of an alarm is changed.Refer to “FCM ON/OFF switch”
on page 6-50.—z When the Forward Collision
Mitigation system (FCM) is
deactivated.Refer to “FCM ON/OFF switch” on page 6-50.

This informs you that a periodic inspection is due.
Screen type 1Screen type 2Solutionz We recommend you to have it checked. Refer to “Service remind-
er” on page 5-16 for further details.
Indication lamp, warning lamp, and information screen display list
5-442*$((Instruments and controls5

The setting for rest interval can be changed.Screen type 1Screen type 2SolutionStop the vehicle in a safe place, turn off the engine, and take a rest. Use this display as rough guide for taking rests during a long drive.
The interval from the start of your trip until this message is displayed
can be set.
Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)” on page 5-18.The display and buzzer alert the driver when the set time is reached. If you continue to drive without having a rest, the buzzer sounds about every 5 minutes to encourage you to take a rest.
z In the following cases, the time driven is reset and the display re-
turns to the previous display screen. After this, when the set time
is reached again, the buzzer and display encourage you to take a rest.

Indication lampsTurn-signal indication lamps/Hazard warning indication lamps
These indication lamps blink in the following situations.

CAUT,ONzIn the situations listed below, brake perform-
ance may be compromised or the vehicle may become unstable if brakes are applied
suddenly; consequently, avoid driving at
high speeds or applying the brakes suddenly. Furthermore, the vehicle should be brought
to a stop in a safe location and to have it checked.

CAUT,ONzIf it illuminates while the engine is running,
there is a problem in the charging system.
Immediately park your vehicle in a safe place and we recommend you to have it
checked.Information screen displayBrake warning displayType 1Type 2
This warning is displayed if you drive with
the parking brake still applied. The warning lamp in the instrument cluster only illumi-
nates when the parking brake is applied.
CAUT,ONz If a vehicle is driven without releasing the
parking brake, the brake will be overheated,
resulting in ineffective braking and possible brake failure.
If this warning is displayed, release the park-
ing brake.Type 1Type 2
When the ignition switch is turned to the
“ON” position or the operation mode is put in
ON, if the brake fluid is low, this warning is displayed.
The warning lamp in the instrument cluster
also illuminates.
CAUT,ONz If this warning stays illuminated and does
not go out while driving, there is a danger of ineffective braking. In this case, immediately
park your vehicle in a safe place and we rec-
ommend you to have it checked.
z If the brake warning display is displayed and
the brake warning lamp and the ABS warn-
ing lamp are illuminated at the same time, the braking force distribution function will
not operate, so the vehicle may be destabi-
lised during sudden braking. Avoid sudden braking and high-speed driving, stop the ve-
hicle in a safe place, and we recommend you
to have it checked.
z The vehicle should be brought to a halt in
the following manner when brake perform- ance has deteriorated.