MITSUBISHI ASX 2019 Owner's Manual (in English)

:ARN,NGzCheck with a
MITSUBISHI MOTORS
Authorized Service Point when it is neces-
sary to repair a high intensity discharge headlamp or to replace the bulb.
High voltage is generated in the high in-
tensity discharge headlamp bulb and elec- trodes, which may cause a severe shock when the bulb and connector are removed or disconnected.Headlamps (High-beam)
1. Turn the cap (A) anticlockwise to re-
move it.
*: Front of the vehicle
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. While holding down the tab (C), pull out
the socket (D).
*: Front of the vehicle
4. To install the bulb, perform the removal
steps in reverse.
CAUT,ONz Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
z Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., andrefit it after drying it thoroughly.Position lamps (type 1)
1. Turn the socket (A) anticlockwise to re-
move it.
Replacement of lamp bulbs
10-272*$((Maintenance10

*: Front of the vehicle
2. Pull the bulb out of the socket.
3. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
To remove
1. Remove the upper cover.
For information regarding how to re-move the upper cover, refer to “Remov-
ing and installing the upper cover and duct” on page 10-09.
2. Remove the entire socket and bulb as-
sembly (A) by turning it anticlockwise.
*: Front of the vehicle
3. Remove the bulb by pulling it out.
To install 1. To install the bulb, perform the removal
steps in reverse.
2. Install the upper cover. For information regarding how to installthe upper cover, refer to “Removing and
installing the upper cover and duct” on page 10-09.Side turn-signal lamps (on
fender)*NOTEz For the side turn-signal lamps (on fender), it
is not possible to repair or replace just the bulb.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.Side turn-signal lamps (on out-
side rear-view mirror)*NOTEz An LED, not a bulb, is used in the side turn-
signal lamps (on outside rear-view mirror).
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-282*$((Maintenance10

Front fog lamps*
1. Remove the clip (A).
2.Insert a straight blade (or minus) screw-
driver with a cloth over its tip into the fog lamp cover (B) and pry gently to re-
move it.
3. Remove the screws (C) and remove the
lamp unit.NOTEz Except for vehicles equipped with daytime
running lamps, when unfastening the screws,be careful not to move the beam position ad-
justment screw (D).4. While holding down the tab (E), pull out
the socket (F).
5. Turn the bulb (G) anticlockwise to re-
move it.
6. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-292*$((Maintenance10

CAUT,ONzHandle halogen lamp bulbs with care. The
gas inside a halogen lamp bulbs is highly
pressurized, so dropping, knocking, or scratching a halogen lamp bulb can cause it
to shatter.
z Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the fog lamps are op- erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying it thoroughly.NOTEz When refitting the clip, first insert part (H)
of the clip into the hole and then press part(I) into it.Daytime running lamps* / Posi-
tion lamps (Type 2)*NOTEz The daytime running lamps/position lamps
(Type 2) use an LED instead of a bulb.Check with a MITSUBISHI MOTORS Au-
thorized Service Point when the lamp needs to be repaired or replaced.Rear fog lampNOTEz The rear fog lamp uses an LED instead of a
bulb. Check with a MITSUBISHI MOTORS
Authorized Service Point when the lamp needs to be repaired or replaced.Rear combination lamps
1. Remove the screws (A) that hold the
lamp unit and remove the lamp unit.
2. Turn the socket and bulb assembly anti-
clockwise to remove it.
Replacement of lamp bulbs
10-302*$((Maintenance10

B- Stop and tail lamp (LED) - cannot be
replaced
C- Rear turn-signal lamps
NOTEz An LED, not a bulb, is used in the stop
lamp/tail lamp. Contact a MITSUBISHI
MOTORS Authorized Service Point when
there is a need for repair or replacement.
3. Pull the bulb out of the socket.
4. To install the bulb, perform the removal
steps in reverse.NOTEz When mounting the lamp unit, align the
groove (D) on the lamp unit with the clip onthe body and the pin (E) on the unit with the
hole in the body.Reversing lamps
1. Open the tailgate.
2. Insert a straight blade (or minus) screw-
driver into the notch of the cover and pry
gently to remove the cover.
NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
cover.
3. Remove the socket and bulb assembly
by turning it anticlockwise.
Replacement of lamp bulbs
10-312*$((Maintenance10

4. Remove the bulb by pulling it out.
5.To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lid, align the tab on the
lid with the hole on the vehicle side.Licence plate lamps
1. When removing the lamp unit (A), push
it towards the left side of the vehicle
body.
2. Remove the socket (B) and bulb assem-
bly by turning it anticlockwise.
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lamp, insert tab (C) first
then align and insert tab (D).
Replacement of lamp bulbs
10-322*$((Maintenance10

High-mounted stop lampNOTEzAn LED, not a bulb, is used in the high-
mounted stop lamp.
Contact a MITSUBISHI MOTORS Author-
ized Service Point when there is a need for
repair or replacement.
Replacement of lamp bulbs
10-332*$((Maintenance10

2*$((

Vehicle labeling................................................................................. 11-02
Vehicle dimensions............................................................................11-04
Vehicle performance..........................................................................11-06 Vehicle weight................................................................................... 11-06
Engine specifications........................................................................ 11-08
Electrical system............................................................................... 11-09
Tyres and wheels............................................................................... 11-10
CO 2 Mass Emissions......................................................................... 11-11
Capacity.............................................................................................11-126pecifications
2*$((11

Vehicle labeling
Vehicle identification number
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code, etc.
Please use this number when ordering re-
placement parts.
1- Model code
2- Engine model code
3- Transmission model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped on the plate riveted to the left front corner of
the vehicle body. It is visible from outside of
the vehicle through the windscreen.
Vehicle labeling
11-022*$((Specifications11