MITSUBISHI ASX 2020 Owner's Manual (in English)

10- Information screen (when the ignitionswitch or the operation mode is ON)
o p. 5-09
Interrupt display screen (when the igni-
tion switch or the operation mode is ON)
o p. 5-14
11- Fuel remaining display screen o p. 5-1512- Outside temperature display screen
o p. 5-14
13- Auto Stop & Go (AS&G) display screen* o p. 6-15
Auto Stop & Go (AS&G) OFF display screen* o p. 6-1514- Engine coolant temperature display
o p. 5-10
15- Gearshift indicator display screen* o p. 6-20
16- Selector lever position display screen* o p. 5-14, 6-25NOTEz The fuel units, temperature units, display language, and other settings can be changed.
Refer to “Changing the function settings (when the ignition switch or the operation mode is ON)” on page 5-17.
z The display screen is different depending on whether the ignition switch or the operation mode is OFF or ON.
Refer to “Information screen (when the ignition switch or the operation mode is OFF)” on page 5-06.
Refer to “Warning display list (when the ignition switch or the operation mode is OFF)” on page 5-26.
Refer to “Information screen (when the ignition switch is turned from the “LOCK” position to the “ON” position or the operation mode is changed from OFF to ON)” on page 5-08.
Refer to “Information screen (when the ignition switch or the operation mode is ON)” on page 5-09.
Refer to “Warning display list (when the ignition switch or the operation mode is ON)” on page 5-29.

Multi-information meter
switch
Each time the multi-information meter switch is operated, a sound is emitted and the multi-
information display changes between infor-
mation such as warnings, tripmeter, service
reminder, average and momentary fuel con-
sumption, driving range, and average speed.Multi-information display
5-052*$(20(1Instruments and controls5

It is also possible to change elements such as
the language and units used on the multi-in- formation display by operating the multi-in- formation meter switch. mark display screen (when
the ignition switch or the oper- ation mode is OFF)
If you press the multi-infor- mation meter switch and re-
turn from the warning dis- play screen to the previous
screen, the
mark is dis-
played.
Refer to “To return to the screen displayed
before the warning display” on page 5-07.
This mark is also displayed if there is another
warning other than the one displayed. When
the cause of the warning display is elimina- ted, the
mark goes out automatically.
NOTEz When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-06.
Refer to “Information screen (when the igni- tion switch or the operation mode is ON)”
on page 5-09.Information screen (when the
ignition switch or the operation mode is OFF)
Each time you lightly press the multi-infor-
mation meter switch, the display screen switches in the following order.
*1: When there is no warning display
*2: When there is a warning display 1- Tripmeter
2- Tripmeter
3- Service reminder
4- Redisplay of a warning display screenOdometer/Tripmeter
Odometer
The odometer indicates the distance travel- led.
Tripmeter
The tripmeter indicates the distance travelled
between two points.

Example usage of tripmeter
and tripmeter
It is possible to measure two currently
travelled distances, from home using
tripmeter
and from a particular point
on the way using tripmeter
.
To reset the tripmeter
To return the display to 0, hold down the multi-information meter switch for approxi- mately 2 seconds or more. Only the currently
displayed value will be reset.
Example
Multi-information display
5-062*$(20(1Instruments and controls5

If tripmeter is displayed, only tripmeter
will be reset.NOTEzIf there is no warning display, the switching
sequence is: Tripmeter
W Tripmeter

W Service reminder
W Tripmeter .
z Both tripmeters
and can count up to
9999.9 km (9999.9 miles).
When a tripmeter goes past 9999.9 km
(9999.9 miles), it returns to 0.0 km (0.0 miles).
z When disconnecting the battery terminal, the
memories of tripmeter display
and dis-
play
are erased, and their displays return
to 0.0 km (0.0 miles).
Service reminder
This displays the distance
and number of months until the next periodic inspection.
Refer to “Service reminder”
on page 5-15.
Interrupt display screen (when
the ignition switch or the oper-ation mode is OFF)
When there is information to be announced, such as lamp reminders, the buzzer sounds
and the multi-information display switches to the warning display screen. Refer to the ap-
propriate page and take the necessary meas- ures.
When the cause of the warning display is eliminated, the warning display goes out au-tomatically.
Refer to “Warning display list (when the igni-
tion switch or the operation mode is OFF)” on page 5-26.
1- Information generated
2- Cause eliminated
To return to the screen dis- played before the warning dis-
play
Even if the cause of the warning display is
not eliminated, you can return to the screen
that was displayed before the warning dis-
play.
Multi-information display
5-072*$(20(1Instruments and controls5

If you press the multi-information meter
switch, the display screen switches to the screen that was displayed before the warning
display and the
mark (A) is displayed.
NOTEz Warning display screens with a “” or “”
mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi-informa-
tion meter switch as follows.
“
”: Press lightly.
“
”: Press for approximately 2 seconds or
more.
Redisplay of a warning display screen
When the mark is displayed, if you lightly
press the multi-information meter switch a
few times, the warning display screen you switched from is displayed again.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-06.Door ajar warning display
screen (when the ignitionswitch or the operation mode is OFF)
If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or tailgate.
1- Doors and tailgate are closed
2- Doors or tailgate are open
Information screen (when the
ignition switch is turned fromthe “LOCK” position to the“ON” position or the operation mode is changed from OFF toON)
When the ignition switch is turned to the
“ON” position or the operation mode is put in
ON, the display screen switches in the fol- lowing order.
1- Screen when the ignition switch or the
operation mode is OFF
2- System check screen
3- Screen when the ignition switch or the
operation mode is ON
Multi-information display
5-082*$(20(1Instruments and controls5

System check screen
When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, the system check screen is displayed forapproximately 4 seconds. If there is no fault,
information screen (when the ignition switch
or the operation mode is ON) is displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list (when the igni-
tion switch or the operation mode is ON)” on
page 5-29.
NOTEz The system check screen display varies de-
pending on the customer

1- Tripmeter
2- Tripmeter
3- Service reminder
4- Driving range display, momentary fuel
consumption display
5- Average fuel consumption display, mo-
mentary fuel consumption display
6- Average speed display, momentary fuel
consumption display
7- Function setting screen
8- Redisplay of a warning display screen
NOTEz While driving, even if you operate the multi-
information meter switch, the function set- ting screen is not displayed. Always stop thevehicle in a safe place before operating.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-17.
z When there is information to be announced,
such as a system fault, the buzzer soundsand the screen display is switched.
Refer to “Interrupt display screen (when the
ignition switch or the operation mode is ON)” on page 5-14.Odometer/Tripmeter
The operation method is the same as when
the ignition switch or the operation mode is OFF.
Refer to “Odometer/Tripmeter” for further details on page 5-06.
Service reminder
This displays the distance
and number of months until
the next periodic inspection. Refer to “Service reminder” on page 5-15.
Engine coolant temperature
display
This indicates the engine coolant temperature.
If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driving.
CAUT,ONz If the engine is overheating, “” will blink.
In this case, the bar graph is on the red zone.
lmmediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-04.Driving range display
This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below approximately 50 km (30 miles), “---” is dis-
played.
Refuel as soon as possible.
Multi-information display
5-102*$(20(1Instruments and controls5

NOTEzThe driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
z When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
z On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is due to the movement of fuel in the tank and
does not indicate a malfunction.
z The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-17.Average speed display
This displays the average speed from the last
reset to the present time.
There are the following 2 mode settings.
For the method for changing the average
speed display setting, refer to “Changing the
function settings (when the ignition switch or the operation mode is ON)” on page 5-17.
Manual reset mode
z When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed displayed at that time is reset.
z When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system@
Turn the ignition switch from the “ACC”
or “LOCK” position to the “ON” posi- tion.
[For vehicles equipped with keyless op-
eration system@
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done, however, the data from the last reset isdisplayed.
Auto reset mode z When the average speed is being dis-
played, if you hold down the multi-infor-
mation meter switch, the average speed
displayed at that time is reset.
Multi-information display
5-112*$(20(1Instruments and controls5

zWhen the engine switch or the operation
mode is in the following conditions, the
average speed display is automatically reset.
[Except for vehicles equipped with key-
less operation system@
The ignition switch is in the “ACC” or
“LOCK” position for approximately 4
hours or longer.
[For vehicles equipped with keyless op- eration system@
The operation mode is in ACC or OFF
for approximately 4 hours or longer.NOTEz The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
z “---” is displayed when the average speed
cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings (when the ignition switch is “ON”)” on page
5-17.
z The memory of the auto reset mode or man-
ual reset mode for the average speed display is erased if the battery is disconnected.Average fuel consumption dis-
play
This displays the average fuel consumption
from the last reset to the present time.
There are the following 2 mode settings.
For information on how to change the aver-
age fuel consumption display setting, refer to “Changing the function settings (when the ig- nition switch or the operation mode is ON)”
on page 5-17.

The “” mark (A) in the momentary fuel
gauge shows the average fuel consumption.

Manual reset mode
z When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the average fuel consumption displayed at
that time is reset.
z When the following operation is per-
formed, the mode setting is automatical- ly switched from manual to auto.
[Except vehicles equipped with keyless
operation system@
Turn the ignition switch from the “ACC”
or “LOCK” position to the “ON” posi-
tion.
[For vehicles equipped with keyless op-
eration system@
Change the operation mode from ACC or OFF to ON.

Switching to auto occurs automatically.
If switching to manual mode is done, however, the data from the last reset isdisplayed.
Auto reset mode
z When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the
average fuel consumption displayed at that time is reset.
Multi-information display
5-122*$(20(1Instruments and controls5

zWhen the engine switch or the operation
mode is in the following conditions, the
average fuel consumption display is au-
tomatically reset.
[Except for vehicles equipped with key-
less operation system@
The ignition switch is in the “ACC” or “LOCK” position for approximately 4
hours or longer.
[For vehicles equipped with keyless op- eration system@
The operation mode is in ACC or OFF
for approximately 4 hours or longer.NOTEz The average speed display and the average
fuel consumption display can be reset indi-vidually for the auto reset mode and manual
reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con-
sumption may vary from the actual fuel con- sumption. Treat the fuel consumption dis-played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-
sumption display is erased if the battery is disconnected.NOTEz The display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km`.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-17.Momentary fuel consumption
display
While driving, this displays the momentary fuel consumption, using a bar graph.
When the value of momentary fuel consump-tion surpasses the value of average fuel con-
sumption, the momentary fuel consumption
is displayed with a white bar graph.
Be conscious of maintaining the value of mo- mentary fuel consumption below the value ofaverage fuel consumption, driving with the
better fuel consumption can be possible.
NOTEz When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.
z The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km`.
Refer to “Changing the function settings (when the ignition switch or the operationmode is ON)” on page 5-17.
z It is possible to cancel the green bar graph.
Refer to “Changing the function settings
(when the ignition switch or the operation mode is ON)” on page 5-17.Function setting screen
The “Display language”,
“Temperature unit”, “Fuel consumption unit”, and
“Average fuel consumption
and speed reset method” etc. settings can be modified as
desired.
Refer to “Changing the function settings
(when the ignition switch or the operation
mode is ON)” on page 5-17 for further de-
tails.
Multi-information display
5-132*$(20(1Instruments and controls5

Interrupt display screen (whenthe ignition switch or the oper- ation mode is ON)
Warning display
When there is information to be announced, such as a system fault, a sound is emitted and
the information screen switches to the warn- ing display screen.
Refer to the warning list and take the neces-
sary measures.
Refer to “Warning display list (when the igni-
tion switch or the operation mode is ON)” on page 5-29.
When the cause of the warning display is eliminated, the warning display goes out au-tomatically.
To return to the screen displayed before
the warning display
Even if the cause of the warning display is not eliminated, you can return to the screen
that was displayed before the warning dis-
play.

If you press the multi-information meter
switch, the display screen switches to the
screen that was displayed before the warning display and the
mark (A) is displayed.
NOTEz Warning display screens with a “” or “”
mark displayed in the upper right of the screen can be switched. If you want to switch the display, press the multi-informa-
tion meter switch as follows.
“
”: Press lightly.
“
”: Press for approximately 2 seconds or
more.
Redisplay of a warning display
screen
When the mark is displayed, if you lightly
press the multi-information meter switch a
few times, the warning display screen you switched from is displayed again.
Other interrupt displays
The operation status of each system is dis-
played on the information screen.
Refer to the appropriate page in the warning
display list for further details.
Refer to “Other interrupt displays” on page 5-40.
Selector lever position display
screen*
Shows the position of the se- lector lever.
Refer to “Selector lever op- eration” on page 6-22.
Outside temperature display
screen
This shows the temperature
outside the vehicle.
NOTEz The display setting can be changed to the
preferred units (