amp MITSUBISHI ECLIPSE 2003 Service Repair Manual

AC003056
Denotes connector No.
The same connector No. is used throughout the circuit diagrams to facilitate connector location searches.
The first alphabetical symbol indicates the location site of the connector and a number that follows is the unique number.
Numbers are usually assigned to parts in clockwise order on the diagram.
Example: A-19
Number specific to connector (serial number)
Connector location site symbol
A: ENGINE COMPARTMENT
B: ENGINE AND TRANSAXLE
C: DASH PANEL
D: FLOOR AND ROOF <ECLIPSE>
D: FLOOR AND WINDSHIELD APERTURE <ECLIPSE SPYDER>
E: DOOR
F: LUGGAGE COMPARTMENT
Denotes ground point.
Same ground number is used throughout circuit
diagrams to facilitate search of ground point.
Refer to GROUP 70 SINGLE PART INSTALLATION
POSITION - GROUND MOUNTING LOCATIONS
for details of ground points.
Denotes the color of the corrugated
tube (If not specified, it is black.)
R: Red
Y: Yellow
The number of connector pins and the connector color
(except milk white)* are shown for ease of retrieval.
Example: (2-B)
Connector color
(milk white if no color is indicated)
Number of connector pins
*: Typical connector colors
B: Black BR: Brown
Y: Yellow V: Violet
L: Blue O: Orange
G: Green GR: Gray
R: Red NONE: Milk white
A-15 (2) FOG LIGHT (RH)
A-16 (2-GR) HORN (LOW)
A-17 (2-B) HEADLIGHT (RH)
A-18 (2-B) WINDSHIELD WASHER MOTOR
A-19 (2-GR) DUAL PRESSURE SWITCH
Indicates the device to which the
connector is connected.
The mark shows the
standard mounting position
of wiring harness.
AE
A-17
A-16
A-15 A-18 A-19
YDenotes a section covered by a
corrugated tube.
FRONT
WIRING
HARNESS
(RH)
Denotes harness name.

AC106592
Amplifier Power Supply Circuit
AB
AC106477
CONNECTOR: C-89
AD
CONNECTOR BLOCK (LH)
AC106483AL
CONNECTOR <ECLIPSE> : D-20

AC004632
AB
Speaker System Circuit <Vehicles Without Amplifier>

AC004630
Speaker System Circuit <Vehicles With Amplifier>
AB

AC003587
Indicates a splice point number.
The splice point numbers are identical to those in &#34;CIRCUIT DIAGRAMS,&#34; making them easy to use.
In addition, the splice point numbers are usually numbered clockwise.
Example: S 013
Sequential number
Prefix meaning splice point
S013
S014
AB
S015 S016
S033
S032
S031

AC106604
Indicates that the terminal is a
spare one if the device (sensor
in this case) is not provided.
Indicates representative vehicle
body ground point. (Same
number as that of ground point in
GROUNDING LOCATION).
Indicates harness junction where
wire diameter or color changes.
In case two or more connectors
are connected to the same de-
vice, markings indicating the
same connector are connected
by a broken line.
Indicates terminal number.
A broken line indicates that these
connectors are the same interm-
ediate connectors.
Indicates intersections at
which the lead wires are
not connected.
Indicates intersections at
which the lead wires are
connected.
Indicates input/output
to/from control unit
(current flow direction).
InputOutputInput/
output
Indicates current flow downward
or upward as controlled by the
control unit.
AB
Indicates that the diagram comes
from which belongs to the
block in the same circuit.
Indicates a wiring connector which is inside
the equipment and which is not shown in
the wiring harness configuration diagram.
Example C-15-2
Indicates a connector
which is inside the
equipment, numbered
in order starting from 1.
Indicates the connector number shown in
the wiring harness configuration diagram.

ACX02377AB
Battery
ACX02378AB
Buzzer
ACX02379AB
Capacitor
ACX02380AB
Electrolytic
capacitor
ACX02381AB
Va r i a b l e
capacitor
ACX02382
AB
Coil
ACX02383AB
Diode
ACX02384
Light emitting
diode
ABACX02385
Photo diode
ABACX02386
AB
Zener diode
ACX02387
AB
Dual bulb
ACX02388AB
Single bulb
ACX02389AB
Fuse
ACX02390AB
Fusible link
ACX02391
AB
Horn
ACX02392
AB
Motor
ACX02393AB
Pulse generator
ACX02394
AB
Piezoelectric
device
ACX02395 AB
Resistor
ACX02396AB
Variable resistor
ACX02397
AB
Speaker
ACX02398AB
Thermistor
ACX02399AB
Transistor
ACX02400
AB
Photo transistor
ACX01279AB
<F> 1.25 G B
1234
Example:

WARNING
WARNING
AKX01214
VOLTMETER
AMMETERLOAD
CHARGING
WARNING LIGHT
IGNITION
SWITCH
INDICATOR LAMP
(BRAKE WARNING LIGHT, etc.)
BATTERY +
–ECM <M/T>
PCM <A/T>GENERATOR
FR
L
S
G
AB

WARNING
WARNING
AKX01215
LOAD
AMMETER
CHARGING
WA R N I N G
LIGHT IGNITION
SWITCH
BLACK
GENERATOR
INDICATOR LAMP
(BRAKE WARNING
LIGHT, etc.)
G
SL
FR
BLUE
YELLOW
RED
VOLTMETER
(DIGITAL-TYPE) BATTERY+
–ECM (M/T)
PCM (A/T)
AB
MB991519

AKX00278
kV
0 SECONDARY
IGNITION
VOLTAGE
WAVE PATTERNIGNITION VOLTAGE
(POINT D)SPARK LINE (POINT A)
DWELL SECTIONWAVE DAMPING REDUCTION SECTION (POINT B)
POINT C
TIME
AB