display MITSUBISHI ENDEAVOR 2011 1.G Owner's Guide

3-106 Features and controls
3
Graph indication
N00501800039
The average speed, average fuel economy, elevation, and out-
side temperature are each shown as a graph at the same time as
being shown numerically.
The range for which historical data are shown in the graphs
changes each time the “RANGE” function button is pressed
lightly.

-3 hours: The average value is added to the graph every 6
minutes. Data for a maximum of three hours are shown in
the graph.

-12 hours: The average value is added to the graph every
24 minutes. Data for a maximum of twelve hours are
shown in the graph.
NOTE
When the range for which historical data are shown is
changed for one graph, it also changes for the other
graphs.Display unit selection
N00501900027
When you want to select the other unit, pressing the function
button (A) for more than 3 seconds changes the unit as follows.
Mode
Unit
Driving range miles
→km
→milesAverage speed mph
→km/h
→mph
Average fuel economy mpg
→L/100km
→mpg
Elevation feet (ft)
→m
→feet (ft)
BK0121600US.book 106 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-107
3
NOTE
When the unit is changed for one display, it is automati-
cally also changed for the other displays.
Door open warning
N00500300037
When any of the doors or the liftgate is not fully closed, a door
open warning (A) is shown.
It is possible to turn off the indication by gently pressing the
“DISP” button.NOTE
It is possible to operate the display using the function but-
tons while the door open warning is being shown.

It is possible to customize the manner in which the door
open warning is shown.
For details, refer to “Setting and customization” on page
3-108.
BK0121600US.book 107 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-108 Features and controls
3
Setting and customization
N00533500055
It is possible to adjust/set/customize the specifications and dis-
plays of the items shown in the table below.
Condition
Item
Condition
Reference
page
DisplayDisplay brightness adjust-
ment*
1
P. 3 - 1 1 2
Turn off display
*
1
P. 3 - 1 1 4
Record maintenance
*
1, *3
P. 3 - 1 1 5
Display settings
*
1, *3
P. 3 - 1 1 8
Units
*
1, *3
P.3-120
Door open warning
*
1, *3
P.3-123
Rheostat synchronization
*
1, *3
P.3-125
Timer buzzer setting
*
1, *3
P.3-126
History
*
1, *3
P.3-127
Opening display setting
*
1, *3
P.3-128
Calendar Date setting
*
1, *3
P.3-130
CompassZone code setting
*
2, *3
P.3-131
Compass calibration
*
2, *3
P.3-133
Customi-
zationLights
*
1, *3
P.3-135
Wipers
*
1, *3
P.3-139
Keyless entry system &
power door lock system*
1, *3
P.3-142
Buzzers
*
1, *3
P.3-147
Number of keyless entry
registration*
1, *3
P.3-150
Defaults
*
1, *3
P.3-151
*
1Adjustment/setting/customization is possible with the igni-
tion key in the “ACC” or “ON” position.
*2Adjustment/setting is possible with the ignition key in the
“ON” position.
*3Setting/customization is possible when the vehicle speed is
no higher than 1mph (2 km/h).
Item
Condition
Reference
page
BK0121600US.book 108 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-109
3
Basic operation
N00535400087
NOTE
Every time the “DISP” button is pressed lightly, the moni-
tor will return to the previous display.

When the “BACK” function button is shown, pressing it
causes the monitor to return to the previous display.
1. Press the “DISP” button for at least 2 seconds to change
the display.2. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “1.Display brightness adjustment” → P. 3 - 1 1 2
• “2.Turn off Display” → P. 3 - 1 1 4
• “3.Record Maintenance” → P. 3 - 1 1 5
• “4.Next menu (Operable only with vehicle stationary)”
→ Proceed to step 3 of this procedure.
CAUTION
!
It is dangerous to operate the display while driving
the vehicle. Operate the display only when the vehi-
cle is safely parked.
BK0121600US.book 109 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-110 Features and controls
3
3. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “1.Date setting” → P. 3 - 1 3 0
• “2.Compass setting” → Proceed to step 5 of this proce-
dure.
• “3.Display settings, customization, other setting.(Refer
to owner’s manual when setting)” → Proceed to step 4
of this procedure.4. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “Display customization” → Proceed to step 6 of this
procedure.
• “Vehicle customization” → Proceed to step 7 of this
procedure.
• “Number of keyless entry registration”
→ P. 3 - 1 5 0
• “Defaults” → P.3-151
BK0121600US.book 110 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-111
3
5. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “Zone code setting” → P. 3 - 1 3 1
• “Compass calibration” → P. 3 - 1 3 36. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “Display settings” → P. 3 - 1 1 8
• “Units” → P. 3 - 1 2 0
• “Door open warning” → P. 3 - 1 2 3
• “Other settings” → P.3-124
BK0121600US.book 111 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-112 Features and controls
3
7. Press the “ ” function button, align the cursor with the
desired setting, and press the “SELECT” function button.
• “Lights”
→ Refer to “Lights customization” on page 3-135
•“Wipers”
→ Refer to “Wipers customization” on page 3-139
• “Keyless entry system & power door lock system”
→ Refer to “Keyless entry system & power door lock
system customization” on page 3-142
• “Buzzers”
→ Refer to “Buzzers customization” on page 3-147
Display brightness adjustment
N00533800074
It is possible to adjust the display brightness that is seen when
the light switch is “OFF”.
When the light switch is in the “ ” or “ ” position, it is
possible to make fine adjustments after making adjustments
using the instrument panel light dimmer control.NOTE
When the light switch is in the “ ” or “ ” position,
pressing the “BRIGHT” function button causes the bright-
ness to change to that seen when the light switch is
“OFF”.
To return the brightness to the original level, press the
“BRIGHT” function button again.
BK0121600US.book 112 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-113
3
1. Display “1. Display brightness adjustment” on the moni-
tor in accordance with “Basic operation” (see page 3-
109), align the cursor with it, and press the “SELECT”
function button.2. Press the “+” or “-” function button to change the bright-
ness. Pressing “+” or “-” function button for more than 1
second will fast forward to the desired change.
When the brightness has been adjusted, press the “SET”
function button. The display will return to its previous dis-
play.
NOTE
The brightness level can be confirmed from the bar posi-
tion in the scale.
BK0121600US.book 113 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

3-114 Features and controls
3
Turn off display
N00533900059
It is possible to set the monitor to give no display.
When the display turns on again, press the “DISP” button. The
display will return to its previous display.
1. Display “2. Turn off display” on the monitor in accor-
dance with “Basic operation” (see page 3-109), align the
cursor with it, and press the “SELECT” function button.2. To set the monitor to give no display, press the “YES”
function button.
If you press the “NO” function button, the monitor will
return to the display in step 1 of this procedure.
NOTE
Even with no display, the display comes on momentarily
at the following times:
• When conditions for display of the road surface freeze
warning symbol are satisfied
• When an air conditioning system adjustment is made
• When an audio system adjustment is made
BK0121600US.book 114 ページ ２０１０年４月１２日　月曜日　午前１０時３９分

Features and controls
3-115
3
Record maintenance
N00501000031
For each of the following items, it is possible to set the date
when maintenance was last performed and the driving distance
until the next maintenance.

Engine oil

Oil filter

Rotate tires

Air purifier

A/T Fluid

Brake system

*
1, *2
NOTE
Use *
1 and *
2 if you wish to set the dates when mainte-
nance was performed for components not shown on the
display.

Maintenance times and reminders were not set before the
vehicle left the factory, so they are initially displayed as “-
--”. To set them, follow the instructions in “Checking and
setting maintenance information” (see page 3-116)

Depending on the vehicle model and specifications, some
of the functions on the monitor may not operate.
Maintenance reminder
N00502700019
When the distance driven reaches a distance that has been set
for scheduled maintenance, the maintenance reminder (A) is
shown to indicate that the time for maintenance has come.NOTE
The maintenance reminder appears when the distance
driven reaches the distance that has been set for any one of
the maintenance items.

When the monitor has been set to give no display, the
maintenance reminder is not shown when the distance
driven reaches a distance that has been set.
BK0121600US.book 115 ページ ２０１０年４月１２日　月曜日　午前１０時３９分