MITSUBISHI L200 2019 Owner's Manual (in English)

Indication and warning lamps (multi information display)1- Front fog lamp indication lamp*o p. 5-12
2- Turn-signal indication lamps/Hazard warning indication lamps o p. 5-12
3- High-beam indication lamp o p. 5-12
4- Auto Stop & Go (AS&G) indication lamp* o p. 6-23
5- Lane departure warning (LDW) standby indication lamp (green)* o p. 6-75
Lane departure warning (LDW) lamp
(amber)* o p. 6-75
6- Position lamp indication lamp* o p. 5-12
7- Lane departure warning (LDW) system ON indication lamp* o p. 6-758- Rear fog lamp indication lamp
o p. 5-12
9- Cruise control indication lamp* o p. 6-63
10- Diesel particulate filter (DPF) warning lamp o p. 6-21
11- Diesel preheat indication lamp o p. 5-12
12- Charge warning lamp o p. 5-14
13- Check engine warning lamp o p. 5-14
14- Fuel filter indication lamp o p. 5-13
15- A/T (automatic transmission) fluid tem- perature warning lamp (vehicles with
A/T) o p. 6-33
16- Oil pressure warning lamp o p. 5-1417- Auto Stop & Go (AS&G) OFF indica-
tion lamp* o p. 6-26
18- Washer fluid level warning lamp* o p. 5-15
19- Multi-information display o p. 5-02
20- For details, refer to “Warning activation” on page 3-12 (if so equipped).
21- For details, refer to “Warning activation” on page 3-12 (if so equipped).
22- Door ajar warning lamp o p. 5-15
23- Seat belt reminder/warning lamp o p. 4-08
24- Anti-lock brake system (ABS) warning lamp o p. 6-57
Indication and warning lamps (multi information display)
5-112.7((Instruments and controls5Type 1
Type 2

25- Active Stability & Traction Control(ASTC) indication lamp o p. 6-61
26- Active Stability & Traction Control (ASTC) OFF indication lamp
o p. 6-61
27- Supplement Restraint System (SRS) warning lamp o p. 4-3428- Brake warning lamp o p. 5-13
29- Rear differential lock indication lamp* o p. 6-45
30- 2WD/4WD operation indication lamp* o p. 6-38
31- Low-range indication lamp* o p. 6-3832- 2WD/4WD operation indication lamp*
o p. 6-42
33- Low-range indication lamp* o p. 6-42

Indication lampsTurn-signal indication lamps/
Hazard warning indication lamps
These indication lamps blink in the following situations.
z When the turn-signal
lever is moved to acti- vate a turn-signal lamp.
Refer to “Turn-signal
lever” on page 5-19.
z When the hazard warning flasher switch
is pressed to activate the hazard warning lamps.
Refer to “Hazard warning flasher switch” on page 5-20.
z When the hazard warning lamps auto-
matically activate due to sudden braking
while driving.
Refer to “Emergency stop signal sys-
tem*” on page 6-56.
High-beam indication lamp
This indication lamp illumi-
nates when the high-beam is
used.
Front fog lamp indication
lamp*
This lamp illuminates while
the front fog lamps are on.
Rear fog lamp indication lamp
This lamp illuminates while
the rear fog lamp is on.
Position lamp indication lamp*
This indication lamp illumi-
nates while the position
lamps are on.
Diesel preheat indication lamp
This indicates the glow plug
preheat condition.
[Except for vehicles equip-
ped with keyless operation
system@
When the ignition switch is
turned to the “ON” position, the lamp illumi- nates. As the glow plug becomes hot, thelamp goes out and the engine can be started.
[For vehicles equipped with keyless opera-
tion system@
Indication lamps
5-122.7((Instruments and controls5

When the operation mode is put in ON, the
lamp illuminates and preheating of the glow plug starts automatically. As the glow plug
becomes hot, the lamp goes out and the en-
gine starts.CAUT,ONz If the diesel preheat indication lamp comes
on after the engine is started, the engine speed may not rise above the idling speedbecause of fuel freezing. In this case, keep
the engine idling for about 10 minutes, then turn off the ignition switch or put in OFF the operation mode, and immediately turn it on
or put in ON again to confirm that the diesel preheat indication lamp is off.NOTEz If the engine is cold, the diesel preheat indi-
cation lamp is on for a longer time.
z [Except for vehicles equipped with keyless
operation system@
When the engine has not been started within about 5 seconds after the diesel preheat indi- cation lamp went out, return the ignition
switch to the “LOCK” position. Then, turn
the ignition switch to the “ON” position to preheat the engine again.
z When the engine is warm, the diesel preheat
indication lamp does not come on even if the
ignition switch is placed in the “ON” posi-
tion or the operation mode is in ON.Fuel filter indication lamp
This indication lamp illumi-
nates when the ignition
switch is turned to the “ON”
position or the operation
mode is put in ON, and goes off after the engine has star-
ted. If it lights up while the engine is running,
it indicates that water has accumulated inside the fuel filter; if this happens, take action as
follows.

Remove the water from the fuel filter. Refer to “Removal of water from the fuel filter” on
page 8-11.

When the lamp goes out, you can resume
driving. If it either does not go out or comes on from time to time, we recommend you tohave the vehicle inspected.
Warning lampsBrake warning lamp
This lamp illuminates when
the ignition switch is turned to the “ON” position or the operation mode is put in ON,
and goes off after a few sec- onds.
Always make sure that the lamp goes off be-
fore driving.
With the ignition switch or the operation
mode in ON, the brake warning lamp illumi-
nates under the following conditions:
z When the parking brake lever has been
engaged.
z When the brake fluid level in the reser-
voir falls to a low level.
z When the brake force distribution func-
tion is not operating correctly.

With the ignition switch or the operation mode in ON, a buzzer sounds under the fol-
lowing condition:
z The vehicle speed exceeds 8 km/h
(5 mph) with the parking brake applied.CAUT,ONz In the situations listed below, brake perform-
ance may be compromised or the vehicle may become unstable if brakes are applied
suddenly; consequently, avoid driving at
high speeds or applying the brakes suddenly. Furthermore, the vehicle should be brought
to a stop in a safe location and to have it checked.

CAUT,ON

If the warning lamp illuminates while the en-
gine is running, turn the engine off and have it inspected.CAUT,ONz If this lamp illuminates when the engine oil
level is not low, have it inspected.
z This warning lamp does not indicate the
amount of oil in the crankcase. This must be determined by checking the oil level on the
dipstick, while the engine is switched off.
z If you continue driving with low engine oil
level or with this warning lamp illuminated,
engine seizure may occur.NOTEz The oil pressure warning lamp should not be
treated as an indication of the engine’s oillevel. The oil level must be checked using
the dipstick.Door ajar warning lamp
This lamp illuminates when
a door is either open or not
completely closed.
If the vehicle speed reaches approximately 8 km/h
(5 mph) with a door open or
incompletely closed, a buzzer sounds 4 times as a warning.
CAUT,ONz Before moving your vehicle, check that the
warning lamp is OFF.Washer fluid level warning
lamp*
This lamp comes on when the washer fluid is running
low.
If the lamp comes on, re- plenish the container with
washer fluid.
Refer to “Washer fluid” on page 10-07.
refer to “Capacity” on page 11-17.
Combination headlamps
and dipper switch
Headlamps
NOTEz Do not leave the lamps on for a long time
while the engine is stationary (not running).A run-down battery could result.NOTEz When it rains, or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy, but this does not indicate a functional problem.
When the lamp is switched on, the heat will
remove the fog. However, if water gathers inside the lamp, we recommend you to have
it checked.
z The bulbs of the high intensity discharge
headlamps (if so equipped) have the follow-
ing characteristics.

Type 1
Rotate the switch to turn on the lamps.
OFFAll lamps offPosition, tail, licence plate and instru-
ment panel lamps onHeadlamps and other lamps go onType 2
Rotate the switch to turn on the lamps.
OFFAll lamps off
AUTO
With the ignition switch or the
operation mode is in ON, head-
lamps, position, tail, licence plate
and instrument panel lamps turn
on and off automatically in ac-
cordance with outside light level.
All lamps turn off automatically
when the ignition switch is turned
to “OFF” position or the opera-
tion mode is put in OFF.Position, tail, licence plate and in-
strument panel lamps onHeadlamps and other lamps go onNOTEz The sensitivity of the automatic on/off con-
trol can be adjusted. For further information,contact a MITSUBISHI MOTORS Author-
ized Service Point.
z If the front fog lamps (if so equipped) turn
on when they are supposed to with the
switch in the “AUTO” position, the lamps turn off automatically with the ignition
switch or operation mode off.
z When the headlamps are turned off by the
automatic on/off control with the ignition
switch in the “ON” position or the operation
mode in ON, the front fog lamps (if so
equipped) and rear fog lamps also go off.
When the headlamps are subsequently turned back on by the automatic on/off con-
trol, the front fog lamps also come on but the
rear fog lamp stays off. If you wish to turn
the rear fog lamp back on, operate the switch again.
z Do not cover the sensor (A) for the automat-
ic on/off control by affixing a sticker or label to the windscreen.
Combination headlamps and dipper switch
5-162.7((Instruments and controls5

NOTEzIf the lamps do not turn on or off with the
switch in the “AUTO” position, manually
operate the switch and we recommend you
to have your vehicle checked.
Lamps (headlamps, fog lamp,
etc.) auto-cutout function
z If the following operation is performed
while the lamp switch is in the “” po-
sition, the lamps are automatically
turned off when the driver’s door is
opened.
[Except vehicles equipped with keyless
operation system@
The ignition switch is turned to the
“LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless op- eration system@
The operation mode is in OFF or ACC.
z If the following operation is performed
while the lamp switch is in the “” po-
sition, the lamps are automatically
turned off if the driver’s door then re-
mains closed for approximately three minutes.
[Except vehicles equipped with keyless
operation system@
The ignition switch is turned to the
“LOCK” or “ACC” position, or the key is removed from the ignition switch.
[For vehicles equipped with keyless op- eration system@
The operation mode is in OFF or ACC.NOTEz The lamp auto-cutout function can also be
disabled.
For further information, we recommend you
to consult a MITSUBISHI MOTORS Au-
thorized Service Point.Lamp monitor buzzer
If the following operation is performed, a
buzzer will sound to remind the driver to turn
off the lamps.
[Except for vehicles equipped with keyless
operation system@
If the driver’s door is opened when the key is
in the “LOCK” or “ACC” position or re-
moved from the ignition switch while the lamps are on.
[For vehicles equipped with keyless opera-
tion system@
If the driver’s door is opened when the opera- tion mode is in ACC or OFF while the lamps
are on.

In both cases, the buzzer will automatically stop if the auto-cutoff function is activated,
the lamp switch is turned off, or the door is closed.Daytime running lamp
The daytime running lamps comes on when
the engine is running and the lamp switch is in the “OFF” or “AUTO” position and the taillamps are off.
Combination headlamps and dipper switch
5-172.7((Instruments and controls5

Dipper (High/Low beamchange)
When the lamp switch is in the “” posi-
tion, the beam changes from high to low (or
low to high) each time the lever is pulled
fully (1). While the high-beam is on, the
high-beam indication lamp in the instrument
cluster will also illuminate.
Headlamp flasher
The high-beams flash when the lever is
pulled slightly (2), and will go off when it is released.
When the high-beam is on, the high-beam in- dication lamp in the instrument cluster will il-
luminate.
NOTEz The high-beams can also flash when the
lamp switch is OFF.
z If you turn the lamps off with the headlamps
set to high-beam, the headlamps are auto- matically returned to their low-beam setting
when the lamp switch is next turned to the
“
” position.
Headlamp levelling switch
The angle of the headlamp beam varies de-
pending on the load carried by the vehicle.
The headlamp levelling switch can be used to adjust the headlamp illumination distance(when the lower beam is illuminated) so that the headlamps’ glare does not distract the
drivers of approaching vehicles.
Set the switch (referring to the following ta-
ble) to the appropriate position according to the number of people and the load in the ve-hicle.CAUT,ONz Always perform adjustments before driving.
Do not attempt to adjust while driving, as it could cause an accident.NOTEz When adjusting the beam position, first put
the dial in the “0” position (the highest beamposition).Vehicle con-
dition
(Single cab)
Headlamp levelling switch
5-182.7((Instruments and controls5

Switch posi-tion“0”“2”

Hazard warning flasherswitch
Use the hazard warning flasher switch when
the vehicle has to be parked on the road for
any emergency.
The hazard warning flashers can always be
operated, regardless of the ignition switch po-
sition or the operation mode.
Push the switch to turn on the hazard warning flashers, all turn-signal lamps flash continu-
ously.
To turn them off, push the switch again.NOTEz On vehicles equipped with the emergency
stop signal system, while the hazard warning lamps are blinking due to having manually
pushed the switch, the emergency stop signal
system does not operate.
Refer to “Emergency stop signal system*” on page 6-56.Fog lamp switch*Front fog lamp switch*
The front fog lamps can be operated while
the headlamps or tail lamps are on. Turn the
knob in the “ON” direction to turn on the front fog lamps. An indication lamp in the in-
strument cluster will also come on. Turn the knob in the “OFF” direction to turn off the front fog lamps. The knob will automatically
return to its original position when you re- lease it.
NOTEz The front fog lamps are automatically turned
off when the headlamps or tail lamps are turned off. To turn the front fog lamps on again, turn the knob in the “ON” directionafter turning on the headlamps or tail lamps.
z Do not use fog lamps except in conditions of
fog, otherwise excessive lamp glare may temporarily blind oncoming vehicle drivers.Rear fog lamp switch
The rear fog lamp can be operated when the
headlamps or front fog lamps (if so equipped)
turn on.
An indication lamp in the instrument cluster comes on when the rear fog lamp is turned
on.

[Vehicle without front fog lamps@
Turn the knob once in the “ON” direction to turn on the rear fog lamp. To turn the rear fog lamp off, turn the knob once in the “OFF” di-
rection. The knob will automatically return to
its original position when you release it.

[Vehicle with front fog lamps@
Hazard warning flasher switch
5-202.7((Instruments and controls5