MITSUBISHI L200 2019 Owner's Manual (in English)

1- Open the glove box.
2- Move the rod (A) on the right side of the
glove box to the right side of the box. (if
so equipped)
3- While pressing the side of the glove box,
unhook the left and right hooks (B) and lower the glove box.
4- Remove the glove box fastener (C), and
then remove the glove box.
Engine compartment
In the engine compartment, the fuse block is
located as shown in the illustration.
1- Push the tab.
2- Remove the cover.
Fuse load capacity
The fuse capacity and the names of electrical systems protected by the fuses are indicated
on the inside of the fuse lid (LHD vehicles),
the back side of the glove box (RHD vehi-
cles) and inside of the fuse block cover (in- side of the engine compartment).
Fuses
10-172.7((Maintenance10

NOTEzSpare fuses are provided in the fuse block of
the engine compartment. Always use a fuse
of the same capacity for replacement.Passenger compartment fuse lo-
cation tableNo.Sym- bolElectrical sys- temCa-
pacity1Tail lamp (left)7.5 A
2
Cigarette lighter
15 A
Cigarette lighter/
Accessory sock-
et3Ignition coil10 A* : Fusible linkNo.Sym-
bolElectrical sys- temCa-
pacity4Starter motor7.5 A5Sunroof20 A6Accessory sock- et15 A7Tail lamp (right)7.5 A8Outside rear-view mirrors7.5 A9Engine control unit7.5 A10Control unit7.5 A11Rear fog lamp10 A12Central doorlock15 A13Room lamp15 A14Rear windowwiper15 A15Gauge10 A16Relay7.5 A17Heated seat20 A18Option10 A*: Fusible linkNo.Sym-
bolElectrical sys- temCa-
pacity19Heated door mirror7.5 A20Windscreen wip- er20 A21Reversing lamps7.5 A22Demister30 A23Heater30 A24Power seat40 A*25Radio10 A26Electronic con-
trolled unit20 A*: Fusible link
z Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
z The table above shows the main equip-
ment corresponding to each fuse.
Fuses
10-182.7((Maintenance10

Engine compartment fuse loca-tion tableNo.Sym- bolElectrical sys- temCa-
paci- tiesSBF1Fuse (+B)30 A *SBF2Anti-lock brake
system30 A *SBF3Ignition switch40 A*SBF4Electric window
control30 A **
: Fusible link
No.Sym-
bolElectrical sys- temCa-
paci- tiesBF1

No.Sym-bolElectrical sys- temCa-
paci- ties2

4.Insert a new fuse of the same capacity
by using the fuse puller into the same
place at the fuse block.CAUT,ONz If the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
z Never use a fuse with a larger capacity than
specified or a substitute (such as a cable or foil). Doing so could cause the circuit wires
to overheat and create a fire.Replacement of lamp bulbs
Before replacing a bulb, ensure the lamp is
off. Do not touch the glass part of the newbulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.
CAUT,ONz Bulbs are extremely hot immediately after
being turned off.
When replacing a bulb, wait for it to cool
sufficiently before touching it. You could otherwise be burnt.
z Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres- surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.
z Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be
cleaned with alcohol, paint thinner, etc., and refit it after drying it thoroughly.CAUT,ONz Do not install commercially available LED-
type bulbs.
Commercially available LED-type bulbs
could adversely affect the operation of the
vehicle, such as by preventing the lamps and other vehicle equipment from operating
properly.NOTEz If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
z Be careful not to scratch the vehicle body
when removing a lamp and lens.
z When it rains or when the vehicle has been
washed, the inside of the lens sometimes be- comes foggy. This is the same phenomenon
as when window glass mists up on a humid day, and does not indicate a functional prob-
lem. When the lamp is switched on, the heat will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have the lamp checked.
Replacement of lamp bulbs
10-212.7((Maintenance10

Bulb location and capacityCAUT,ONzWhen replacing a bulb, be sure to use a new
bulb of the same type, wattage and colour. If you install a different bulb, the bulb could malfunction or fail to come on and could
lead to a vehicle fire.Outside
Front
Except for vehicles with high intensity dis-
charge headlamps 1. Position lamps: 5 W (W5W)
2. Front turn-signal lamps: 21 W (PY21W/
P21W)
3. Headlamps, high/low beam: 60/55 W
(H4)
4. Type 1
Front fog lamps: 35 W (H8)
Daytime running lamps: 13 W (P13W)
Type 2
Daytime running lamps: 13 W (P13W)
5. Side turn-signal lamps (on fender)* 1
, * 2
:
5 W
6. Side turn-signal lamps (on outside rear-
view mirror)* 1
Vehicles with high intensity discharge
headlamps 1. Front turn-signal lamps: 21 W (PY21W)
2. Position lamps/Daytime running lamps
3. Headlamps, high/low beam: 25 W (D5S) 4. Front fog lamps: 19 W (H16)
5. Side turn-signal lamps (on fender)* 1
, * 2
:
5 W
6. Side turn-signal lamps (on outside rear-
view mirror)* 1*
1
:if so equipped* 2
:Have the lamps bulbs replaced
at a MITSUBISHI MOTORS
Authorized Service point.
Codes in parentheses indicate bulb types.
:ARN,NGz Check with a
MITSUBISHI MOTORS
Authorized Service Point when it is neces-
sary to repair a high intensity discharge headlamp or to replace the bulb.
High voltage is generated in the high in-
tensity discharge headlamp bulb and elec- trodes, which may cause a severe shock when the bulb and connector are removed or disconnected.NOTEz It is not possible to repair or replace only the
bulb for the side turn-signal lamp (on fend-
er).
Check with a MITSUBISHI MOTORS Au-
thorized Service point when the lamp needs to be repaired or replaced.
Replacement of lamp bulbs
10-222.7((Maintenance10

Rear
1- High-mounted stop lamp
2- Tail and stop lamps: 21/5 W (P21/5W)
3- Rear turn-signal lamps: 21 W (PY21W)
4- Rear fog lamp (driver’s side): 21W
(P21W)
Reversing lamps: 21 W (P21W)
5- Licence plate lamps: 5 W (W5W)
Codes in parentheses indicate bulb types.
NOTEz The following lamps uses LEDs rather than
bulbs. For repair and replacement, contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.

NOTEzWhen moving the upper cover towards the
rear of the vehicle, remove the harness fromthe air cleaner hooks (C).
*: Front of the vehicle
z After replacing the bulb, make sure that the
hinges at the front of the vehicle are firmly
set.
2. Disconnect the connector (A).
3. Remove the sealing cover (B).
4. Unhook the spring (C) which secures the
bulb, and then remove the headlamp bulb.
5. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-242.7((Maintenance10

Position lamps
1.When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold-
ing down the washer tank spout and move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by pulling out.
3. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
Except for vehicles with high in- tensity discharge headlamps
1. When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold- ing down the washer tank spout and
move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by turning it anticlockwise while
pressing in.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-252.7((Maintenance10

Vehicles with high intensity dis-charge headlamps
1. When replacing the bulb on the left side
of the vehicle, remove the clip (A) hold-
ing down the washer tank spout and move the spout towards the rear of the
vehicle.
2. Turn the bulb socket anticlockwise to re-
move it. And remove the bulb from the socket by turning it anticlockwise while
pressing in.
3. To install the bulb, perform the removal
steps in reverse.
Front fog lamps* / Daytime
running lamps*
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
of the cover (A) and pry gently to re-
move the cover.
2. Remove the 3 screws (B) and remove
the lamp unit.
Replacement of lamp bulbs
10-262.7((Maintenance10