MITSUBISHI L200 2020 (in English) Owners Manual

Instruments.......................................................................................... 5-02
Multi information display - Type 1..................................................... 5-03
Multi information display - Type 2..................................................... 5-17
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)............................ 5-25
Indication and warning lamps (multi information display - Type 2)............................................................................................ 5-49
Indication lamps.................................................................................. 5-50
Warning lamps.................................................................................... 5-51
Information screen display (Vehicles equipped with the multi information display - Type 1)................................................ 5-53
Combination headlamps and dipper switch........................................ 5-55
Headlamp levelling switch.................................................................. 5-61
Turn-signal lever................................................................................. 5-62
Hazard warning flasher switch............................................................5-62 Fog lamp switch.................................................................................. 5-63
Wiper and washer switch.................................................................... 5-64 Rear window demister switch............................................................. 5-68
Heated steering wheel*....................................................................... 5-70
Horn switch......................................................................................... 5-70,nstrumentsandcontrols
2.7(20(15

Instruments
1- TachometerThe tachometer indicates the engine
speed (r/min). The tachometer helps you to obtain more economical driving and
also warns you of excessive engine
speeds (Red zone).
2- Multi information display (Type 1: Col-
our liquid crystal display type) o p. 5-03
Information screen display list (Type 1)
o p. 5-26
Multi information display (Type 2: Mono-colour liquid crystal display type)
o p. 5-17
3- Speedometer (km/h or mph + km/h)
4- Rheostat illumination button (Type 1)
o p. 5-02
5- Multi information display switch (Type
2) o p. 5-18CAUT,ONz When driving, watch the tachometer to make
sure that the engine speed indication does not rise into the red zone (excessive engine
rpm).Meter illumination control -
Type 1
Each time you press the rheostat illumination button, there is a sound and the brightness of
the instruments changes.
1- Brightness level
2- Rheostat illumination button
NOTEz You can adjust to 8 different levels respec-
tively for when the position lamps are illu- minated and when they are not.
z If the vehicle is equipped with the automatic
lamp control, when the lamp switch is in a position other than the “OFF” position, the
meter illumination switches automatically to
the adjusted brightness, depending on the
brightness outside the vehicle.
Instruments
5-022.7(20(1Instruments and controls5Type 1
Type 2

NOTEzThe brightness level of the instruments is
stored when the ignition switch is turned off
or the operation mode is put in OFF.
z If you press and hold the button for about 2
seconds or more when the position lamps are
illuminated, the brightness level changes to
the maximum level. Pressing and holding the button for about 2 seconds or more again returns the brightness level to the previous
level.Multi information display -
Type 1
Always stop the vehicle in a safe place before operating.
The following information is included on the multi information display: warnings, odome-
ter, tripmeter, average and momentary fuel
consumption, average speed etc.
[When the ignition switch or the operation
mode is OFF@
1- mark display o p. 5-07
2- Information screen o p. 5-05
Interrupt display screen o p. 5-06
3- Odometer o p. 5-08
4- “
” or “” mark indicator o p. 5-06
[When the ignition switch or the operation
mode is ON@
1- Off Road mode indicator display*
o p. 6-53
2- Drive mode indicator display* (Vehicles
with Easy Select 4WD) o p. 6-43
(Vehicles with Super Select 4WD II)
o p. 6-49
3-
mark display o p. 5-07
4- Forward Collision Mitigation system
(FCM) OFF indicator display* o p. 6-94
Ultrasonic misacceleration Mitigation
System (UMS) OFF indicator display* o p. 6-105
Multi information display - Type 1
5-032.7(20(1Instruments and controls5

5-Lane Departure Warning (LDW) indica-
tor display* o p. 6-112
6- Information screen o p. 5-05
7- Engine coolant temperature display
o p. 5-07
8- Odometer o p. 5-08
9- Cruise control indicator display
o p. 6-80
10- Speed limiter indicator display*
o p. 6-84
11- “
” or “” mark indicator o p. 5-06
12- Gearshift indicator display (vehicles
with M/T) o p. 6-29
13- Selector lever position indicator display
(vehicles with A/T) o p. 6-33
14- Fuel remaining display o p. 5-07
15- Outside temperature display o p. 5-08
16- Auto Stop & Go indicator display*
o p. 6-25
Auto Stop & Go OFF indicator display* o p. 6-28
NOTEz The fuel units, outside temperature units,
display language, and other settings can bechanged.
Refer to “Changing the function settings” on page 5-13.Multi information display
switch
Each time the multi information display
switch is operated, the buzzer sounds and the
multi information display changes between
information such as warnings, tripmeter, average and momentary fuel consumption,
distance range etc.
It is also possible to change elements such as the language and units used on the multi in-formation display by operating the multi in-
formation display switch.
NOTEz Each time the multi information display
back switch is operated, the buzzer sounds and the multi information display return to
the position before pressing the multi infor- mation display switch.
Multi information display - Type 1
5-042.7(20(1Instruments and controls5

Information screen (when theignition switch or the operation mode is OFF)
Each time you lightly press the multi infor-
mation display switch, the display screen
switches in the following order.
* 1
: When there is no warning display
* 2
: When there is a warning display
1- Tripmeter
o p. 5-08
2- Tripmeter
o p. 5-08
3- Auto Stop & Go (AS&G) monitor* o p. 5-12
ECO score display o p. 5-12
4- Service reminder o p. 5-09
5- Redisplay of a warning display screen o p. 5-06
Information screen (when the
ignition switch is turned fromthe “LOCK” position to the “ON” position or the operationmode is changed from OFF to ON)
When the ignition switch is turned to the
“ON” position or the operation mode is put in
ON, the display screen switches in the fol- lowing order.
*: When the inspection time has arrived 1. Screen when the ignition switch or the
operation mode is OFF
2. System check screen o p. 5-10
3. Screen when the ignition switch or the
operation mode is ON
4. Service reminder o p. 5-09
Information screen (when the
ignition switch or the operationmode is ON)
Each time you lightly press the multi infor-
mation display switch, the display screen switches in the following order.
* 1
: When there is no warning display
* 2
: When there is a warning display
1- Tripmeter
o p. 5-08
Multi information display - Type 1
5-052.7(20(1Instruments and controls5

2-Tripmeter o p. 5-08
3- Driving range display o p. 5-10
ECO drive assist display o p. 5-12
4- Average fuel consumption display
o p. 5-11
ECO drive assist display o p. 5-12
5- Average speed display o p. 5-11
Momentary fuel consumption display o p. 5-11
6- Auto Stop & Go (AS&G) monitor*
o p. 5-12
ECO score display o p. 5-12
7- 2WD/4WD operation indicator display*
(Vehicles with Easy Select 4WD)
o p. 6-43
(Vehicles with Super Select 4WD II)
o p. 6-49
8- Service reminder o p. 5-09
9- Function setting screen o p. 5-13
10- Redisplay of a warning display screen
o p. 5-06NOTEz While driving, the service reminder are not
displayed even if you operate the multi in-
formation display switch. Always stop the vehicle in a safe place before operating.NOTEz While driving, the function setting screen is
not displayed even if you operate the multi
information display switch.
Always stop the vehicle in a safe place be- fore operating and firmly apply the parking brake and put the gearshift lever into the “N”
(Neutral) position (M/T ) or the selector lever
into the “P” (PARK) position (A/T).
Refer to “Changing the function settings” on page 5-13.
z When there is information to be announced,
such as a system fault, the buzzer soundsand the screen display is switched.
Refer to “Interrupt display screen” on page 5-06.Interrupt display screen
Warning display
When there is information to be announced,
such as a system fault, the buzzer sounds and the information screen is switched to the
warning display screen.
Refer to the warning list and take the neces- sary measures.
Refer to “Warning display list” on page
5-26.
When the cause of the warning display is
eliminated, the warning display goes out au- tomatically.

To return to the screen displayed before
the warning display
Even if the cause of the warning display is
not eliminated, you can return to the screen that was displayed before the warning dis-
play.
If you press the multi information display switch, the display screen switches to the
screen that was displayed before the warning display and the
mark (A) is displayed.
If you want to switch the dis-
play
Warning display screens with a “ ” or “ ”
mark displayed in the upper right of the
screen can be switched. If you want to switch the display, press the multi information dis-
play switch as follows.
“
”: Press lightly.
“
”: Press for approximately 2 seconds or
more.
Multi information display - Type 1
5-062.7(20(1Instruments and controls5

Redisplay of a warning displayscreen
When the mark is displayed, if you lightly
press the multi information display switch a
few times, the warning display screen you
switched from is redisplayed.
Other interrupt displays
The operation status of each system is dis-
played on the information screen.
Refer to the appropriate page in the warning display list for further details.
Refer to “Other interrupt displays” on page
5-45.
mark display
This is displayed when you press the multi information display switch and return from the warning display screen to the previous
screen.
This mark is also displayed if there is another
warning other than the one displayed.
When the cause of the warning display is eliminated, the
mark goes out automatical-
ly.
NOTEz When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the igni-
tion switch or the operation mode is OFF)” on page 5-05.
Refer to “Information screen (when the igni- tion switch or the operation mode is ON)”
on page 5-05.Engine coolant temperature
display
This indicates the engine coolant temperature.If the coolant becomes hot, “
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUT,ONz If the engine is overheating, “” will blink.
In this case, the bar graph is in the red zone.
Immediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-09.Fuel remaining display
This displays the amount of fuel remaining.
F (1) - Full
E (0) - Empty
NOTEz It may take several seconds to stabilise the
display after refilling the tank.
z If fuel is added with the ignition switch or
the operation mode is in ON, the fuel gauge may incorrectly indicate the fuel level.
z The arrow (A) indicates that the fuel tank
filler door is located on the left side of the
body.
Multi information display - Type 1
5-072.7(20(1Instruments and controls5

Fuel remaining warning dis-play
When the fuel is reduced to approximately 10
litres, the information screen switches to the interrupt display of the fuel remaining warn-
ing display, and the “
” mark (B) on the fuel
remaining display flashes slowly (approxi- mately once per second). After a few sec-
onds, the information screen returns from the fuel remaining warning display to the previ-ous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “
” mark
(B) on the fuel remaining display flashes
quickly (approximately twice per second).
CAUT,ONz Do not drive with an extremely low fuel lev-
el; running out of fuel could cause damage to the fuel system.NOTEz On inclines or curves, the display may be in-
correct due to the movement of fuel in the
tank.Outside temperature display
This shows the temperature
outside the vehicle.
NOTEz The display setting can be changed to the
preferred units (

Service reminder
Displays the approximate time until the next
periodic inspection recommended by
MITSUBISHI MOTORS . “---” is displayed
when the inspection time has arrived.
NOTEz Depending on the vehicle specifications, the
displayed time until the next periodic inspec-
tion may differ from that recommended by
MITSUBISHI MOTORS.
In addition, the display settings for the next periodic inspection time can be modified.
To modify the display settings, have it adjus- ted at a MITSUBISHI MOTORS Authorized
Service Point.
For more details, contact a MITSUBISHI
MOTORS Authorized Service Point.
1. Displays the time until the next periodic
inspection.
NOTEz The distance is shown in units of 100 km
(100 miles). The time is shown in units of months.
2. This informs you that a periodic inspec-
tion is due. Consult a MITSUBISHI
MOTORS Authorized Service Point.
At that time, when the ignition switch is turned from the “LOCK” position to the
“ON” position or the operation mode is
changed from OFF to ON, the warning display is displayed for a few seconds on
the information screen.
3. After your vehicle is inspected at a
MITSUBISHI MOTORS Authorized
Service Point, it displays the time until the next periodic inspection.
To reset
The “---” display can be reset while the igni-
tion switch or the operation mode is in OFF.When the display is reset, the time until the
next periodic inspection is displayed and the
warning display is no longer displayed when the ignition switch is turned from the
“LOCK” position to the “ON” position or the operation mode is changed from OFF to ON. 1. When you lightly press the multi infor-
mation display switch a few times, the
information display switches to the serv- ice reminder display screen.
2. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to display “
” and make it
flash. (If there is no operation for ap-
proximately 10 seconds with flashing, the display returns to the previousscreen.)
Multi information display - Type 1
5-092.7(20(1Instruments and controls5

3.Lightly press the multi information dis-
play switch while the icon is flashing to
change the display from “---” to
“CLEAR”. After this, the time until the
next periodic inspection will be dis- played.CAUT,ONz The customer is responsible for making sure
that periodic inspection and maintenance are
performed.
Inspections and maintenance must be per- formed to prevent accidents and malfunc- tions.NOTEz “---”display cannot be reset when the igni-
tion switch or the operation mode is in ON.NOTEz When “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri- odic inspection is displayed.
z If you accidentally reset the display, consult
a MITSUBISHI MOTORS Authorized Serv-ice Point.System check screen
When the ignition switch is turned to the
“ON” position or the operation mode is put in ON, the system check screen is displayed forapproximately 4 seconds. If there is no fault,
information screen (when the ignition switch
or the operation mode is ON) is displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list” on page
5-26.
NOTEz The system check screen display varies de-
pending on the customer’s equipment.Driving range display
This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below approximately 50 km (30 miles), “---” is dis-
played.
Refuel as soon as possible.
NOTEz The driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
z When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
z On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is due to the movement of fuel in the tank and
does not indicate a malfunction.
Multi information display - Type 1
5-102.7(20(1Instruments and controls5