MITSUBISHI L200 2020 Owner's Manual (in English)

NOTEzThe display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on page 5-13.Average fuel consumption dis-
play
This displays the average fuel consumption
from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched be-
tween “Auto reset” and “Manual reset”.
Refer to “Changing the reset mode for aver-
age fuel consumption and average speed” on
page 5-14.
For information on how to change the aver- age fuel consumption display setting, refer to“Changing the function settings” on page
5-23.
NOTEz The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con- sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis- played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the battery isdisconnected.
z The display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings” on page 5-23.Average speed display
This displays the average speed from the last
reset to the present time.
The reset mode conditions for the average speed display can be switched between “Auto
reset” and “Manual reset”.
Refer to “Changing the reset mode for aver- age fuel consumption and average speed” on
page 5-14.
For the method for changing the average
speed display setting, refer to “Changing the
function settings” on page 5-23.NOTEz The average speed display can be reset sepa-
rately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average speed
cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The display setting can be changed to the
preferred units (km/h or mph).
Refer to “Changing the function settings” on page 5-23.
z The memory of the auto reset mode or man-
ual reset mode for the average speed displayis erased if the battery is disconnected.Momentary fuel consumption
display
While driving, this displays the momentary fuel consumption, using a bar graph.
Multi information display - Type 1
5-112.7(20(1Instruments and controls5

The “ ” mark (A) in the momentary fuel
gauge shows the average fuel consumption. When the momentary fuel consumption sur-
passes the average fuel consumption, the mo- mentary fuel consumption is displayed with a
green bar graph.
Be conscious of maintaining the momentary
fuel consumption above the average fuel con- sumption, driving with the better fuel con-
sumption can be possible.
NOTEz When the momentary fuel consumption can-
not be measured, the bar graph is not dis-
played.
z The display setting can be changed to the
preferred units { km/L, mpg (US), mpg (UK)
or L/100 km}.
Refer to “Changing the function settings” on page 5-23.
z It is possible to cancel the green bar graph.
Refer to “Changing the function settings” on page 5-23.Auto Stop Go (AS G) moni-
tor*
The accumulated time the engine has been stopped by Auto Stop & Go (AS&G) system is displayed.
Refer to “Auto Stop & Go (AS&G) system”
on page 6-25.
NOTEz When the ignition switch or the operation
mode is ON again, the accumulated time
will be reset.ECO drive assist display
This function displays how fuel-efficiently
you are driving under different driving condi-
tions.
The ECO drive assist display will change as follows if you do fuel-efficient driving using
the accelerator in a way well matched with
the vehicle speed.
NOTEz On vehicles with
A/T, the ECO drive assist
is displayed only when vehicle is driving
with the selector lever in the “D” (DRIVE)
position or when vehicle is driving in the
sport mode.ECO score display
ECO score indicates the points you have
scored on fuel-efficient driving by the num-
ber of leaves as follows:

[When the ignition switch or the operation mode is ON@
The display shows the score you achieved in the last several minutes.

[When the ignition switch is turned off or the
operation mode is put in OFF@
Multi information display - Type 1
5-122.7(20(1Instruments and controls5 ECO drive levelLow High

The display shows the overall ECO score thefunction has counted from the time when theignition switch is turned to “ON” to the time when it is turned to “LOCK” or “ACC”, or
from the time when the operation mode is set
to “ON” to the time when it is set to “OFF”.Changing the function settings
The “Display language”, “Temperature unit”,
“Fuel consumption unit”, and “Average fuel consumption and speed reset method” etc.
setting can be modified as desired. 1. Stop the vehicle in a safe place. Firmly apply the parking brake and put
the gearshift lever into the “N” (Neutral) position ( M/T) or the selector lever into
the “P” (PARK) position (A/T).
2. Lightly press the multi information dis-
play switch a few times to switch the in- formation screen to the function setting
screen.
Refer to “Information screen (when the
ignition switch or the operation mode is ON” on page 5-05.CAUT,ONz For safety, stop the vehicle before operating.
While driving, even if you operate the multiinformation display switch, the function set- ting screen is not displayed.
3. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
NOTEz To return the menu screen to the function
setting screen, press and hold the multi in-formation display switch for approximately 2 seconds or more.
z If no operations are made within approxi-
mately 30 seconds of the menu screen being displayed, the display returns to the function
setting screen.
4. Select the item to change on the menu
screen and change to the desired setting. Refer to the following items for further
details on the operation methods.
Refer to “Changing the reset mode for aver-
age fuel consumption and average speed” on
page 5-14.
Refer to “Changing the fuel consumption dis-
play unit” on page 5-15.
Refer to “Changing the temperature unit” on
page 5-15.
Refer to “Changing the display language” on page 5-15.
Refer to “Operation sound setting” on page
5-16.
Refer to “Changing the time until “REST REMINDER” is displayed” on page 5-16.
Refer to “Changing the turn-signal sound” on page 5-16.
Refer to “Changing the momentary fuel con- sumption display” on page 5-17.
Multi information display - Type 1
5-132.7(20(1Instruments and controls5ECO drive levelLow High

Refer to “Returning to the factory settings”on page 5-17.NOTEz If the battery is disconnected, these function
settings are reset from memory and is auto-matically to the factory settings.Changing the reset mode for
average fuel consumption and average speed
The mode conditions for the average fuel consumption and average speed display can
be switched between “Auto reset” and “Man-
ual reset”. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select
“AVG (average fuel consumption andaverage speed setting)”.
3. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from A/1 (Auto reset mode) to M/2/P (Manual reset mode), or from M/2/P to A/1.
The setting is changed to the selected mode condition.
Manual reset mode
z When the average fuel consumption and
average speed are being displayed, if
you hold down the multi information
display switch, the average fuel con-
sumption and average speed displayed at
that time are reset.
z When the following operation is per-
formed, the mode setting is automatical-
ly switched from manual to auto.
[Except for vehicles equipped with key-
less operation system@
Turn the ignition switch from the “ACC” or “LOCK” position to the “ON” posi-
tion.
[For vehicles equipped with keyless op- eration system@
Change the operation mode from ACC
or OFF to ON.

Switching to auto occurs automatically. If switching to manual mode is done,
however, the data from the last reset is displayed.
Auto reset mode
z When the average fuel consumption and
average speed are being displayed, if
you hold down the multi information
display switch, the average fuel con-
sumption and average speed displayed at
that time are reset.
z When the ignition switch or the opera-
tion mode is in the following condition, the average fuel consumption display
and average speed display are automati-
cally reset.
[Except for vehicles equipped with key-
less operation system@
The ignition switch is in the “ACC” or
“LOCK” position for approximately 4 hours or longer.
[For vehicles equipped with keyless op- eration system@
The operation mode is in ACC or OFF
for approximately 4 hours or longer.
NOTEz The average fuel consumption display and
average speed display can be reset separately
for the auto reset mode and for the manual reset mode.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con- sumption display and average speed display
is erased if the battery is disconnected.
Multi information display - Type 1
5-142.7(20(1Instruments and controls5

Changing the fuel consumptiondisplay unit
The display unit for fuel consumption can be
switched. The distance, speed, and amount units are also switched to match the selected
fuel consumption unit. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select
“AVG UNIT (fuel consumption display
setting)”.
3. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to display “AVG UNIT”.
4. Lightly press the multi information dis-
play switch to select the units.
5. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to change the setting to the se-
lected unit.
NOTEz The display units for the driving range, the
average fuel consumption, the average speed and the momentary fuel consumption areswitched, but the units for the indicating
needle (speedometer), the odometer and the tripmeter will remain unchanged.
The distance and speed units are also switch-
ed in the following combinations to match the selected fuel consumption unit.
Fuel con-
sumptionDistance (driving range)Speed (aver- age speed)L/100 kmkmkm/hmpg (US)mile(s)mphmpg (UK)mile(s)mphkm/Lkmkm/hChanging the temperature unit
The display unit for temperature can beswitched. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set- tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select “
” (temperature
unit setting).
3. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch in from

3.Press and hold the multi information dis-
play switch for approximately 2 seconds or more to display “LANGUAGE”.
4. Lightly press the multi information dis-
play switch to select the desired lan- guage.
5. If you hold down the multi information
display switch for approximately 2 sec- onds or more, the setting is changed to
the selected language.NOTEz If “---” is selected in the language setting, a
warning message is not displayed whenthere is a warning display or interrupt dis-
play.Operation sound setting
You can turn off the operation sounds of the
multi information display switch and rheostat
illumination button. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select “
” (operation
sound setting).
3. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from ON (operation sound on) to OFF (operation sound off),
or from OFF to ON.
The setting is changed to the selected condition.NOTEz The operation sound setting only deactivates
the operation sound of the multi information
display switch and rheostat illumination but- ton. The warning display and other soundscannot be deactivated.Changing the time until
“REST REMINDER” is dis-played
The time until the display appears can be changed. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set- tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select “ALARM” (rest time setting).
3. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to display “ALARM”.
4. Lightly press the multi information dis-
play switch to select the time until thedisplay.
5. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more, the setting is changed to the se-
lected time.NOTEz The drive time is reset when the ignition
switch is turned off or the operation mode is
put in OFF.Changing the turn-signal
sound
It is possible to change the turn-signal sound. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select
(changing the
turn-signal sound).
Multi information display - Type 1
5-162.7(20(1Instruments and controls5

3.Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from 1 (turn-signal
sound 1) to 2 (turn-signal sound 2), or from 2 to 1.
The setting changes to the selected turn- signal sound.Changing the momentary fuel
consumption display
It is possible to change the bar graph setting
of the momentary fuel consumption display. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set-
tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select
(changing
the momentary fuel consumption dis-
play).
3. Press and hold the multi information dis-
play switch for approximately 2 seconds or more to switch from ON (with the
green bar graph) to OFF (without the
green bar graph), or from OFF to ON.
The setting changes to the selected bar
graph setting.
Returning to the factory set-
tings
Many of the function settings can be returned
to their factory settings. 1. Press and hold the multi information dis-
play switch for approximately 2 seconds
or more to switch from the setting mode
screen to the menu screen.
Refer to “Changing the function set- tings” on page 5-13.
2. Lightly press the multi information dis-
play switch to select “RESET” (return- ing to the factory settings).
3. When you press and hold the multi in-
formation display switch for approxi-
mately 5 seconds or more, the buzzer sounds and all of the function settings
are returned to the factory settings.
NOTEz The factory settings are as follows.

NOTEzWhen the ignition switch is OFF, the gear-
shift indicator, fuel remaining display and
engine coolant temperature display are not
displayed.Information display
Each time you lightly press the multi information display switch (A), the display switches in the following order.
1- Odometer o p. 5-19
2- Tripmeter
o p. 5-19
3- Tripmeter
o p. 5-19
4- Meter illumination control o p. 5-19
5- Driving range display o p. 5-196- Average fuel consumption display
o p. 5-20
7- Service reminder (distance) o p. 5-21
8- Service reminder (month) o p. 5-21
Multi information display - Type 2
5-182.7(20(1Instruments and controls5

NOTEzWhen the ignition switch is OFF, the driving range display and average fuel consumption display are not displayed.
z While driving, the service reminder is not displayed even if you operate the multi information display switch.

Odometer
The odometer indicates the distance travel-
led.
Tripmeter
The tripmeter indicates the distance travelled
between two points.

Example usage of tripmeter
and tripmeter
It is possible to measure two currently
travelled distances, from home using
tripmeter
and from a particular point
on the way using tripmeter
.

To reset the tripmeter
To return the display to 0, hold down the multi information display switch for about 2
seconds or more. Only the currently dis-
played value will be reset.

Example
If tripmeter is displayed, only tripmeter
will be reset.NOTEz When disconnecting the battery terminal, the
memory of tripmeter and are
cleared, and the display returns to “0”.Meter illumination control
Each time you press and hold the multi infor-
mation display switch (2) for about 2 secondsor more, there is a sound and the brightnessof the instruments changes.
1- Brightness level
2- Multi information display switchNOTEz You can adjust to 8 different levels respec-
tively for when the position lamps are illu- minated and when they are not.
Each time you reduce two brightness levels, the segment display of the brightness level decreases one by one.
z If the vehicle is equipped with the automatic
lamp control, when the lamp switch is in a position other than the “OFF” position, the
meter illumination switches automatically to
the adjusted brightness, depending on the
brightness outside the vehicle.
z The brightness level of the instruments is
stored when the ignition switch is turned off.Driving range display
This displays the approximate driving range
(how many more kilometres or miles you can
drive). When the driving range falls below approximately 50 km (30 miles), “---” is dis-
played.
Multi information display - Type 2
5-192.7(20(1Instruments and controls5

NOTEzThe driving range is determined based on
the fuel consumption data. This may vary depending on the driving conditions and habits. Treat the distance displayed as just a
rough guideline.
z When you refuel, the driving range display
is updated.
However, if you only add a small amount of fuel, the correct value will not be displayed.
Fill with a full tank whenever possible.
z On rare occasions, the value displayed for
the driving range may change if you are
parked on an extremely steep incline. This is due to the movement of fuel in the tank and
does not indicate a malfunction.
z The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on page 5-23.Average fuel consumption dis-
play
This displays the average fuel consumption
from the last reset to the present time.
The reset mode conditions for the average fuel consumption display can be switched be-
tween “Auto reset” and “Manual reset”.
For information on how to change the aver- age fuel consumption display setting, refer to“Changing the function settings” on page
5-23.
NOTEz The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con- sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis- played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the battery isdisconnected.
z The display setting can be changed to the
preferred units {km/L, L/100 km, mpg}.
Refer to “Changing the function settings” on page 5-23.Engine coolant temperature
display
This indicates the engine coolant temperature.If the coolant becomes hot,
“
” will blink.
Pay careful attention to the engine coolant temperature
display while you are driv-
ing.
CAUT,ONz If the engine is overheating, “” will blink.
In this case, the bar graph is in the red zone.
Immediately park the vehicle in a safe place
and take the required measures. Refer to “Engine overheating” on page 8-09.
Multi information display - Type 2
5-202.7(20(1Instruments and controls5