MITSUBISHI L200 2020 Owner's Manual (in English)

ScreenCauseSolution (Reference)zThere is a fault in the urea SCR system
(AdBlue

ScreenCauseSolution (Reference)zThere is a fault in the steering wheel lock.z Immediately stop the vehicle in a safe
place.
We recommend you to consult a MITSU- BISHI MOTORS Authorized Service
Point.
Refer to “Steering wheel lock” on page
6-16.z The steering wheel is locked.z Press the engine switch while turning
steering wheel.
Refer to “Steering wheel lock” on page
6-16.z The engine is stopped while the selector
lever is in a position other than the “P” (PARK) position.z Place the selector lever in the “P” (Park)
position to put the operation mode in OFF.z The driver’s door is opened with the steer-
ing wheel unlocked.z Refer to “Steering wheel lock” on page
6-16.z The keyless operation key is not detected.zInsert the keyless operation key into the
key slot.
Refer to “If the keyless operation key is not operating properly” on page 6-21.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-322.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zYou have forgotten to remove the keyless
operation key from the key slot.z Remove the keyless operation key from
the key slot.
Refer to “Keyless operation key remind-
er” on page 6-21.z The A/T fluid temperature is too high.zRefer to “When a malfunction occurs in
the A/T” on page 6-35.z There is a fault in the A/T.zWe recommend you to have it checked,
immediately.
Refer to “When a malfunction occurs in the A/T” on page 6-35.z [Vehicles with Easy Select 4WD@
The clutch pedal is not depressed during shifting process between “4H”
Y “4L”.z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis-
play” on page 6-43.z [Vehicles with Super Select 4WD II@
The clutch pedal is not depressed during
shifting process between “4HLc”
Y “4LLc”.z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis- play” on page 6-49.z [Vehicles with Easy Select 4WD@
The selector lever is shifted from the “N” (NEUTRAL) position to the other posi-
tion or release the brake pedal during
shifting process between “4H”
Y “4L”z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis- play” on page 6-43.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-332.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)z[Vehicles with Super Select 4WD II@
The selector lever is shifted from the “N” (NEUTRAL) position to the other posi-
tion or release the brake pedal during
shifting process between “4HLc”
Y “4LLc”.z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis-
play” on page 6-49.z There is a fault in the Easy Select 4WD.z Have your vehicle inspected at a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to “Drive mode indicator display and 2WD/4WD operation indicator dis-
play” on page 6-43.z There is a fault in the Super Select 4WD
II.z Have your vehicle inspected at a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to“Drive mode indicator display and 2WD/4WD operation indicator dis-
play” on page 6-49.z [Vehicles with the Easy Select 4WD@
Speed limiter will activate.z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis- play” on page 6-43.z [Vehicles with the Super Select 4WD II@
Speed limiter will activate.z Refer to “Drive mode indicator display
and 2WD/4WD operation indicator dis-
play” on page 6-49.z The Off Road mode will not be available
even if the Off Road mode-selector is
pressed because the drive mode-selector of Super Select 4WD II is in “2H” or
“4H”.z Refer to “Off Road mode-selector opera-
tion” on page 6-53.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-342.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zThe Off Road mode will not be available
even if the Off Road mode-selector is
pressed because the brake system is ab- normally overheated.z Refer to “Off Road mode indicator dis-
play” on page 6-53.z The Off Road mode will not be available
even if the Off Road mode-selector is
pressed because the rear differential lock is activating.z Refer to “Off Road mode indicator dis-
play” on page 6-53.z There is a fault in the rear differential lock
system.z Have your vehicle inspected at a
MITSUBISHI MOTORS Authorized
Service Point as soon as possible.
Refer to “The rear differential lock indica-
tion lamp/display” on page 6-55.z You try to turn on the rear differential
lock switch during driving.z Refer to “Rear differential lock*” on page
6-54.z The Hill Descent Control (HDC) brake
control is not available because the brake system is abnormally overheated.z Refer to “To operate” on page 6-71.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-352.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zThe Hill Descent Control (HDC) cannot
be set to ON (stand by) because the vehi-cle speed is 20 km/h or more.z Refer to “To operate” on page 6-71.zThe Hill Descent Control (HDC) cannot
be set to ON (stand by) because the reardifferential lock is activated.z Refer to “To operate” on page 6-71.zThe Hill Descent Control (HDC) is not
available because the gearshift lever is placed in the forward gear except the 1stposition.z Refer to “To operate” on page 6-71.zThere is a fault in the hill start assist.z We recommend you to have it checked.
Refer to “Warning lamp/display” on page 6-70.z There is a fault in the active stability &
traction control (ASTC).z We recommend you to have it checked.
Refer to “ASTC warning lamp/display” on page 6-79.z There is a fault in the ABS.z Avoid sudden braking and high-speed
driving, stop the vehicle in a safe place, and take corrective measures. Refer to“ABS warning lamp/display” on page
6-74.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-362.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zThe braking system temperature is too
high.z Immediately stop the vehicle in a safe
place.
Refer to “ASTC indication lamp or ASTC
OFF indication lamp” on page 6-78.z The Forward Collision Mitigation system
(FCM) has detected the danger of colli-
sion.z Take appropriate action such as depress-
ing the brake to avoid collision.
Refer to “Forward Collision warning
function” on page 6-90.z The FCM braking function of the Forward
Collision Mitigation system (FCM) has been activated.z Refer to “FCM braking function” on page
6-91.z There is a fault in the Forward Collision
Mitigation system (FCM).z We recommend you to have it checked.
Refer to “When a problem is detected” on
page 6-95.z The Forward Collision Mitigation system
(FCM) is temporarily not available.z Refer to “When a problem is detected” on
page 6-95.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-372.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zWhen the Forward Collision Mitigation
system (FCM) is ON, if the drive modese-
lector of Super Select 4WD II is set to “4LLc”, the FCM will be switched to
OFF automatically.
z When the FCM is OFF, the FCM will not
be switched to ON even if the FCM and
UMS ON/OFF switch is pressed because the drive mode-selector of Super Select4WD II is in “4LLc”.z Refer to “FCM and UMS ON/OFF
switch” on page 6-94.z When the Forward Collision Mitigation
system (FCM) is ON, if the rear differen-
tial lock switch is set to ON, the FCM will
be switched to OFF automatically.
z When the FCM is OFF, even if the FCM
and UMS ON/OFF switch is pressed, the FCM will not be switched to ON because
the rear differential lock switch is ON.z Refer to “FCM and UMS ON/OFF
switch” on page 6-94.
z When the Forward Collision Mitigation
system (FCM) is ON, if the Hill Descent
Control (HDC) is set to ON, the FCM will be switched to OFF automatically.
z When the FCM is OFF, even if the FCM
and UMS ON/OFF switch is pressed, the FCM will not be switched to ON because
the Hill Descent Control (HDC) operates.z Refer to “FCM and UMS ON/OFF
switch” on page 6-94.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-382.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zThe Ultrasonic misacceleration Mitigation
System (UMS) sensor is temporarily not available for some reason such as the en-
vironmental condition or increase of the sensor temperature.z When the warning display does not disap-
pear after waiting for a while, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “When the sensor is temporarily not available” on page 6-106.z The Ultrasonic misacceleration Mitigation
System (UMS) does not operate normally
because there are some malfunctions in the sensor or the system.z We recommend you to have it checked,
immediately.
Refer to “When there is a malfunction in the system or the sensor” on page 6-106.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-392.7(20(1Instruments and controls5

ScreenCauseSolution (Reference)zThe Ultrasonic misacceleration Mitigation
System (UMS) is activated.z Refer to “Ultrasonic misacceleration Miti-
gation System (UMS)” on page 6-100.z When the Ultrasonic misacceleration Mit-
igation System (UMS) is ON, if the drive
mode-selector of Super Select 4WD II is set to “4LLc”, the Ultrasonic misaccelera-
tion Mitigation System (UMS) will be
switched to OFF automatically.
z When the Ultrasonic misacceleration Mit-
igation System (UMS) is OFF, even if the
FCM and UMS ON/OFF switch is press- ed, the Ultrasonic misacceleration Mitiga-
tion System (UMS) will not be switched
to ON because the drive mode-selector of Super Select 4WD II is in “4LLc”.z Refer to
“When the UMS is not available”
on page 6-106.
Indication lamp, warning lamp, and information screen display list (multi information display - Type 1)
5-402.7(20(1Instruments and controls5