MITSUBISHI L200 2020 Owner's Manual (in English)

No.Sym-bolElectrical sys- temCa-
pacity19Heated door mirror7.5 A20Windscreen wip- er20 A21Reversing lamps7.5 A22Demister30 A23Heater30 A24Power seat40 A*25Radio10 A26Electronic con-
trolled unit20 A*: Fusible link
z Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
z The table above shows the main equip-
ment corresponding to each fuse.
Engine compartment fuse loca-
tion tableNo.Sym- bolElectrical sys- temCa-
paci- tiesSBF1Ignition switch40 A *SBF2Electric window
control30 A *SBF3Power seat40 A*SBF4Anti-lock brake
system30 A *SBF5Electric parking
brake30 A*BF1Audio system
amp30 A*: Fusible link
Fuses
10-212.7(20(1Maintenance10 Engine compartment fuse location Behind of the fuse block cover

No.Sym-bolElectrical sys- temCa-
paci- ties
BF2 /
Rear air condi- tioning/ Rear circulator
30 A
BF3

10 A: Option
15 A: Cigarette lighter
When using a substitute fuse, replace with a
fuse of the correct capacity as soon as possi- ble.Identification of fuseCa-
pacityColour7.5 ABrown10 ARed15 ABlue20 AYellow30 AGreen (fuse type) / Pink (fusible link type)40 AGreen (fusible link type)

Fuse replacement
1.Before replacing a fuse, always turn off
the electrical circuit concerned and place
the ignition switch in the “LOCK” posi- tion or put the operation mode in OFF.
2. Remove the fuse puller (A) from the in-
side of the fuse box in the engine com-
partment.
3. Referring to the fuse load capacity table,
check the fuse pertaining to the problem.
B- Fuse is OK
C- Blown fuse
NOTEz If any system does not function but the fuse
corresponding to that system is normal, theremay be a fault in the system elsewhere. We
recommend you to have your vehicle checked.
4. Insert a new fuse of the same capacity
by using the fuse puller into the same
place at the fuse block.
CAUT,ONz If the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
z Never use a fuse with a larger capacity than
specified or a substitute (such as a cable or foil). Doing so could cause the circuit wires
to overheat and create a fire.
Fuses
10-232.7(20(1Maintenance10

Replacement of lamp bulbs
Before replacing a bulb, ensure the lamp is off. Do not touch the glass part of the newbulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.CAUT,ONz Bulbs are extremely hot immediately after
being turned off. When replacing a bulb, wait for it to cool sufficiently before touching it. You couldotherwise be burnt.
z Handle halogen lamp bulbs with care. The
gas inside halogen lamp bulbs is highly pres-
surized, so dropping, knocking, or scratching
a halogen lamp bulb can cause it to shatter.CAUT,ONz Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying it thoroughly.
z Do not install commercially available LED-
type bulbs.
Commercially available LED-type bulbs
could adversely affect the operation of the vehicle, such as by preventing the lamps and
other vehicle equipment from operating properly.
NOTEz If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
z Be careful not to scratch the vehicle body
when removing a lamp and lens.NOTEz When it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem. When the lamp is switched on, the heat will remove the fog. However, if water gath-
ers inside the lamp, we recommend you to have the lamp checked.Bulb location and capacityCAUT,ONz When replacing a bulb, be sure to use a new
bulb of the same type, wattage and colour. If you install a different bulb, the bulb could malfunction or fail to come on and could
lead to a vehicle fire.
Replacement of lamp bulbs
10-242.7(20(1Maintenance10

Outside
Front
Halogen headlamps type A
1. Position lamps: 5 W (W5W)
2. Headlamps, high-beam: 60 W (HB3)
3. Headlamps, low beam: 55 W (H11)
4. Side turn-signal lamps (on fender) *
: 5W
5. Side turn-signal lamps (on outside rear-
view mirror) *
:

NOTEzThe following lamps use an LED instead of
the bulb. If you need to repair or replacethese lamps, contact a MITSUBISHI
MOTORS Authorized Service Point.

NOTEzWhen moving the upper cover towards the
rear of the vehicle, remove the harness fromthe air cleaner hooks (C).
*: Front of the vehicle
z After replacing the bulb, make sure that the
hinges at the front of the vehicle are firmly
set.
2. When replacing the bulb on the left side
of the vehicle, remove the fuse block cover with pushing the tab (D).
3. Turn the cover (E) anticlockwise to re-
move it.
*: Front of the vehicle
4. While holding down the tab (F), pull out
the socket (G) from the bulb, and turn the bulb anticlockwise to remove it.
5. To install the bulb, perform the removal
steps in reverse.
>High-beam@ 1. When replacing the bulb on the right
side of the vehicle, remove the clamps (A) of the air cleaner filter and move the
upper cover (B) towards the rear of the vehicle.
Replacement of lamp bulbs
10-272.7(20(1Maintenance10

*: Front of the vehicle
NOTEzWhen moving the upper cover towards the
rear of the vehicle, remove the harness fromthe air cleaner hooks (C).
*: Front of the vehicle
NOTEz After replacing the bulb, make sure that the
hinges at the front of the vehicle are firmly
set.
2. When replacing the bulb on the left side
of the vehicle, remove the clip (D) hold- ing down the washer tank spout and
move the spout towards the rear of the vehicle.
3. Turn the cover (E) anticlockwise to re-
move it.
*: Front of the vehicle
4. While pulling up the tab (F), pull out the
socket (G) from the bulb, and turn the bulb anticlockwise to remove it.
Replacement of lamp bulbs
10-282.7(20(1Maintenance10

5.To install the bulb, perform the removal
steps in reserve.Position lamps
Vehicles with halogen head-
lamps type A or type B
1. When replacing the bulb on the right
side of the vehicle, remove the clamps
(A) of the air cleaner filter and move the upper cover (B) towards the rear of the
vehicle.
*: Front of the vehicle
NOTEz When moving the upper cover towards the
rear of the vehicle, remove the harness fromthe air cleaner hooks (C).
*: Front of the vehicle
z After replacing the bulb, make sure that the
hinges at the front of the vehicle are firmly
set.
2. When replacing the bulb on the left side
of the vehicle, remove the clip (D) hold- ing down the washer tank spout and
move the spout towards the rear of the vehicle.
3. Turn the cover (E) anticlockwise to re-
move it.
*: Front of the vehicle
Replacement of lamp bulbs
10-292.7(20(1Maintenance10

4. Turn the bulb socket (F) anticlockwise toremove it. And remove the bulb from the
socket by pulling out.
5. To install the bulb, perform the removal
steps in reverse.
Front turn-signal lamps
1. To create enough work space, turn the
steering wheel all the way in the direc- tion opposite to the side you wish to re-
place.
2. Remove the 3 bolts (A) and 1 clip (B),
and then pull back the splash shield (C).
*: Front of the vehicle
3. Turn the bulb socket (D) anticlockwise
to remove it. And remove the bulb from
the socket by turning it anticlockwise while pressing in.
4. To install the bulb, perform the removal
steps in reverse.NOTEz When refitting the clip (B), first insert part
(E) of the clip into the hole and then presspart (F) into it.Front fog lamps* / Daytime
running lamps*
Vehicles with halogen head- lamps type A
1. To create enough work space, turn the
steering wheel all the way in the direc-
tion opposite to the side you wish to re- place.
2. Remove the 3 bolts (A) and 1 clip (B),
and then pull back the splash shield (C).
Replacement of lamp bulbs
10-302.7(20(1Maintenance10