MITSUBISHI L200 2020 Owner's Manual (in English)

*: Front of the vehicle
3. Confirm the position of the bulb to be
replaced.
D- Front fog lamp
E- Daytime running lamp
4. While holding down the tab (F), pull out
the socket (G) from the bulb, and turn the bulb anticlockwise to remove it.
5. To install the bulb, perform the removal
steps in reverse.
NOTEz When refitting the clip (B), first insert part
(H) of the clip into the hole and then press
part (I) into it.Vehicles with halogen head-
lamps type B or LED head-
lamps
1. To create enough work space, turn the
steering wheel all the way in the direc-
tion opposite to the side you wish to re- place.
2. Remove the 3 bolts (A) and 1 clip (B),
and then pull back the splash shield (C).
*: Front of the vehicle
3. Confirm the position of the bulb to be
replaced.
Replacement of lamp bulbs
10-312.7(20(1Maintenance10 Type 1 Type 2 Front fog lamp Daytime running lamp

D- Daytime running lamp
E- Front fog lamp
4. [Daytime running lamp@ Turn the socket (D) anticlockwise to re-
move it, and while holding down the tab
(F), pull out the bulb (G) from the sock-
et.
[Front fog lamp@
While holding down the tab (H), pull out
the socket (I) from the bulb, and turn the
bulb anticlockwise to remove it.
5. To install the bulb, perform the removal
steps in reverse.
NOTEz When refitting the clip (B), first insert part
(J) of the clip into the hole and then press
part (K) into it.Rear combination lamps
1. Open the rear gate.
(Refer to “Rear gate” on page 3-20.)
2. Remove the screws (A) that hold the
lamp unit.
Replacement of lamp bulbs
10-322.7(20(1Maintenance10

3.Move the lamp unit towards the rear of
the vehicle and remove the clips (B).
4. Remove each socket and bulb assembly
by turning it anticlockwise.
C-Rear turn-signal lamp
Remove the bulb by pulling it
out.D-Reversing lamp
Remove the bulb by pulling it out.
5. To install the bulb, perform the removal
steps in reverse.
Licence plate lamps
1. Insert a straight blade (or minus) screw-
driver into the lamp assembly and pry
gently to remove it.
NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens and the body.2. Remove the socket and bulb assembly
together by turning it anticlockwise, and then remove the bulb by pulling it out.
3. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
10-332.7(20(1Maintenance10

NOTEzWhen mounting the lamp unit, put the hook
(A) on the right side of the lamp unit into thebody first.Front room map lamps
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
gently to remove it.
Remove the bulb from the lamp holder.
Vehicles without ERA-GLONASS
Vehicles with ERA-GLONASSNOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lens, align the tab (A) on
the lens with the holes on the vehicle side.Vehicles without ERA-GLONASS
Vehicles with ERA-GLONASS
Rear room lamp
1. Insert a straight blade (or minus) screw-
driver into the notch of the lens and pry
Replacement of lamp bulbs
10-342.7(20(1Maintenance10

gently to remove it. Remove the bulb
from the lamp holder.NOTEz Wrap a piece of cloth around the tip of the
screwdriver in order to avoid scratching the
lens.
2. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lens, align the 2 tabs on
the lens with the holes on the vehicle side.Glove box lamp
Have the glove box lamp bulb replaced at a
MITSUBISHI MOTORS Authorized Service
Point.
Replacement of lamp bulbs
10-352.7(20(1Maintenance10

2.7(20(1

Vehicle labeling................................................................................. 11-02
Vehicle dimensions............................................................................11-04
Vehicle performance..........................................................................11-08 Vehicle weight................................................................................... 11-08
Engine specifications........................................................................ 11-12
Electrical system............................................................................... 11-12
Tyres and wheels............................................................................... 11-13
Fuel consumption.............................................................................. 11-13
Capacity.............................................................................................11-156pecifications
2.7(20(111

Vehicle labeling
Vehicle Identification Number: (VIN)
The vehicle identification number is stamped as shown in the illustration.
Vehicle identification number
plate (RHD vehicles only)
The vehicle identification number is stamped on the plate riveted to the left front corner of the vehicle body. It is visible from outside of
the vehicle through the windscreen.
Vehicle information code plate
The vehicle information code plate is located as shown in the illustration.
The plate shows model code, engine model,
transmission model and body colour code, etc.
Please use this number when ordering re-
placement parts.
Vehicle labeling
11-022.7(20(1Specifications11

1- Model code
2- Engine model code
3- Transmission model code
4- Final gear ratio
5- Body colour code
6- Interior code
7- Option codeEngine model/number
The engine model and number are stamped on the engine cylinder block as shown in the
illustrations.
Vehicle labeling
11-032.7(20(1Specifications11

Vehicle dimensions
Vehicle dimensions
11-042.7(20(1Specifications11Club Cab