MITSUBISHI LANCER EVOLUTION 2011 10.G Owners Manual

7-58 Vehicle care and maintenance
7
Front side-marker and parking lights (for vehi-
cles with high intensity discharge headlights)
N00917300466
1. To create enough work space, turn the steering wheel all
the way in the direction opposite to the side you wish to
replace.
2. Remove the clips (A), clip (B) and screw (C) to turn up
the cover (D).3. Turn the socket (E) counterclockwise to remove it.
BK0123500US.book 58 ページ ２０１０年６月４日　金曜日　午後５時１分

Vehicle care and maintenance
7-59
7
4. Pull the bulb out of the socket.
5. To install the bulb, perform the removal steps in reverse.
Front turn signal lights
N00943400253
1. Remove the clips (A) and clips (B), then remove the duct
(C) and the upper cover (D).
BK0123500US.book 59 ページ ２０１０年６月４日　金曜日　午後５時１分

7-60 Vehicle care and maintenance
7
2. Remove the entire socket and bulb assembly (E) by turn-
ing it counterclockwise.3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.*- Front of the vehicle
BK0123500US.book 60 ページ ２０１０年６月４日　金曜日　午後５時１分

Vehicle care and maintenance
7-61
7
Front fog lights
N00943600646
1. Remove the clips (A) and clips (B), then turn up the cover
(C).2. While pressing the tab (D), pull out the socket (E).
3. Turn the bulb (F) counterclockwise to remove it.
BK0123500US.book 61 ページ ２０１０年６月４日　金曜日　午後５時１分

7-62 Vehicle care and maintenance
7
4. To install the bulb, perform the removal steps in reverse.
Rear combination lights
N00943700399
Tail and stop lights, rear turn signal lights and rear
side-marker lights1. Remove the screws (A) from the light unit.
CAUTION
!
Handle halogen light bulbs with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc. The oil from your hand could cause
the bulb to break the next time the fog lights are
used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0123500US.book 62 ページ ２０１０年６月４日　金曜日　午後５時１分

Vehicle care and maintenance
7-63
7
2. Remove the light unit in the rear direction. 3. Remove the socket and bulb assemblies by turning them
counterclockwise.
B- Tail and stop light
C- Rear turn signal light
D- Rear side-marker light
BK0123500US.book 63 ページ ２０１０年６月４日　金曜日　午後５時１分

7-64 Vehicle care and maintenance
7
4. Remove the bulb by pulling it out. 5. To install the bulb, perform the removal steps in reverse.
NOTE
When mounting the light unit, align the pins (E) on the
light unit with the holes in the body.
Tail and stop light and
Rear turn signal lightRear side-marker lightBK0123500US.book 64 ページ ２０１０年６月４日　金曜日　午後５時１分

Vehicle care and maintenance
7-65
7
Tail lights and back-up lights1. Open the trunk lid.
Remove the clips (A) and remove the cover (B).2. Remove the socket and bulb assemblies by turning them
counterclockwise.
C- Tail light
D- Back-up light
BK0123500US.book 65 ページ ２０１０年６月４日　金曜日　午後５時１分

7-66 Vehicle care and maintenance
7
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
License plate light
N00944000344
1. Remove the screws (A) from the license plate lamp lens
(B). Then, remove the lens and gasket (C), and withdraw
the bulb.
Back-up lightTail lightBK0123500US.book 66 ページ ２０１０年６月４日　金曜日　午後５時１分

Vehicle care and maintenance
7-67
7
2. Remove the socket and bulb assembly together by turning
it counterclockwise.3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
BK0123500US.book 67 ページ ２０１０年６月４日　金曜日　午後５時１分