camshaft MITSUBISHI LANCER EVOLUTION IV 1998 Owner's Manual

MPI – Troubleshooting13-26
7. INSPECTION PROCEDURE USING
OSCILLOSCOPE
7-1 AIR FLOW SENSOR (AFS)
Observing waveforms displayed on the oscilloscope allows
you to visually identify possible unusual disturbances in
waveform that could temporarily occur in the air flow sensor
output.
<Measurement procedure>
(1) Disconnect the air flow sensor connector and connect
the special tool (Test Harness: MB991709) to it. (Ensure
that all terminals are connected.)
(2) Connect the oscilloscope probe to terminal no. 3 of air
flow sensor connector.
NOTE
If the engine ECU connector is used, connect the
oscilloscope probe to terminal no. 90.
(3) Perform the same steps from here on as with the 4G9
engine.
7-2 CAMSHAFT POSITION SENSOR AND CRANK
ANGLE SENSOR
Perform the same steps as with the conventional 4G9 engine
for the inspection.
7-3 INJECTOR
Observing waveforms displayed on the oscilloscope allows
you to visually check the conditions of injector drive signals
actually output from the engine ECU.
Injector Control Signal (Oscilloscope 1)
<Measurement procedure>
(1) Disconnect the injector connector and connect the special
tool (Test Harness: MB991348) to the circuit. (Ensure
that the terminals on both the power supply and engine
ECU sides are connected.)
(2) Connect the oscilloscope probe to terminal no. 2 of injector
connector.
NOTE
If the engine ECU connector is used for the measurement,
take measurements at each of the following terminals.
Connect the oscilloscope probe to terminal no. 1 when
the waveform is observed with no. 1 cylinder, to terminal
no. 14 when the waveform is observed with no. 2 cylinder,
to terminal no. 2 when the waveform is observed with
no. 3 cylinder, and to terminal no. 15 when the waveform
is observed with no. 4 cylinder.
Oscilloscope
Oscilloscope

MPI – On-vehicle Service13-31
5. MPI SYSTEM COMPONENTS LAYOUT
NameSymbolNameSymbol
A/C switchQExhaust temperature warning lampS
A/C relayHFuel pressure control valveA
Air flow sensor (with a built-in intake air temperaturesensor and barometric pressure sensor)FIgnition coil and power transistor unitLsensor and barometric pressure sensor)InjectorB
Camshaft position sensorMISC servoD
Control relay and fuel pump relayPOxygen sensorK
Coolant temperature sensorEPower steering fluid pressure switchI
Crank angle sensorJSecondary air control solenoid valveN
Detonation sensorCThrottle position sensor (with a built-in idle switch)D
Diagnosis connectorR
Engine ECUOVehicle speed sensorT
Engine warning lampSWastegate solenoid valveG

16-1
ENGINE
ELECTRICAL
CONTENTS
CHARGING SYSTEM 2. . . . . . . . . . . . . . . .
ALTERNATOR 2. . . . . . . . . . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM 4. . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE 4. . . . . . . . . . . . . . . . . . .
1. Ignition Coil with Built-in Power Transistor
Check 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Spark Plug Check, Cleaning, and
Replacement 4. . . . . . . . . . . . . . . . . . . . . . . . . .
CAMSHAFT POSITION SENSOR AND
CRANK ANGLE SENSOR
5 . . . . . . . . . . . . .

ENGINE ELECTRICAL – Ignition System16-5
CAMSHAFT POSITION SENSOR AND CRANK ANGLE SENSOR
REMOVAL AND INSTALLATION
Pre-removal and Post-installation Operation
Timing Belt Removal and Installation
(Refer to GROUP 11.)
Unit: Nm {kgf
m}
49 {5.0}
5
9 {0.9}9 {0.9}
9 {0.9} 39 {4.0} 3 {0.3}
2
3
41
Removal steps
1. Camshaft position sensor
2. Center cover

A3. Power steering oil pump4. Power steering oil pump bracket
5. Crank angle sensor
REMOVAL SERVICE POINT

APOWER STEERING OIL PUMP REMOVAL
Remove the power steering oil pump with hose from the power
steering oil pump bracket.
NOTE
String up the oil pump which has been removed onto a location
that does not hamper removal and installation of the power
steering oil pump bracket.

MANUAL TRANSMISSION OVERHAUL – Special Tools22B-11
Tool UseName Number
MB990938HandleUse with Installer adapter
MB991445Bushing remover
and installer baseInstallation of differential case taper roller
bearing outer race
MD998304Oil seal installerInstallation of transfer extension housing oil
seal
MD998364Camshaft oil seal
installerInstallation of gear, bearing and sleeve
MD998800Oil seal installerInstallation of differential oil seal and transfer
cover oil seal
MD998801Bearing removerInstallation and removal of gear, bearing and
sleeve
MD998812Installer capUse with Installer and installer adapter
MD998813Installer-100Use with Installer cap and installer adapter
MD998814Installer-200Use with Installer cap and installer adapter