wheel torque MITSUBISHI LANCER EVOLUTION IV 1998 Workshop Manual

ENGINE – Crankshaft Oil Seal11-16
REMOVAL SERVICE POINT
AFLYWHEEL ASSEMBLY REMOVAL
Use the special tool to secure the flywheel assembly and
remove the bolts.
INSTALLATION SERVICE POINTS
ACRANKSHAFT REAR OIL SEAL INSTALLATION
(1) Apply a small mount of engine oil to the entire
circumference of the oil seal lip.
(2) Install the oil seal with the special tool as far as the
chamfered position of the oil seal case as shown in the
illustration.
BFLYWHEEL ASSEMBLY INSTALLATION
Use the special tool to hold the flywheel in the same manner
as removal, and install the bolt. Tighten the bolts to the
specification.
Tightening torque: 127 – 137 Nm {13.0 – 14.0 kgf
m}
CCRANKSHAFT FRONT OIL SEAL INSTALLATION
Apply a small amount of engine oil to the entire circumference
of the oil seal lip.
Pressfit the oil seal until it is flush with the chamfered end
of the oil pump case.
MD998781
Crankshaft
rear oil seal
MB990938
MB998776Crankshaft
Crankshaft
MD998382
Oil seal
MD998285
(Lubricate outer
circumference with oil)

REAR AXLE – Service Specifications / Lubricant / Sealant27-2
SERVICE SPECIFICATIONS
<Vehicles with AYC>
ItemsStandard valueLimit
Rear axle total backlash mm–5
Pressure generated by hydraulic unit MPa {kgf/cm2}0 – 1.6 {10.0 – 16.0}–
Wheel bearing axial play mm–0.05
Wheel bearing rotation starting torque Nm {kgf
cm}–1.0 {10.5} or less
<Vehicles without AYC>
ItemsStandard valueLimit
Right-to-left difference in combined thickness of friction plate and fric-
tion disc mm0 – 0.05–
Clearance between spring plate and differential case mm0.06 – 0.25–
LSD differential torque
Nm {kgf
m}
When new clutch plate is installed5 – 19 {0.5 – 1.9}–
Nm {kgf
m}
When existing clutch plate is installed2 – 19 {0.2 – 1.9}–
Distortion of friction plate and friction disc mm–0.08
Difference in thickness between friction plate, friction disc, and spring
plate mm–0.1
LUBRICANT
<Vehicles with AYC>
ItemsSpecified lubricantCapacity
Gear oilTorque
transfer
differential
DifferentialMITSUBISHI GENUINE DIA QUEEN SUPER
HYPOID GEAR OIL (GL-5)0.41 ± 0.02 dm3
{0.41 ± 0.02 }
differentialTorque transfer
mechanismMITSUBISHI GENUINE DIA QUEEN AYC FLUID0.700
0.05dm3
{0.700
0.05}
Hydraulic piping fluidMITSUBISHI GENUINE DIA QUEEN ATF-SPII1 dm3 {1 }
Torque transfer mechanism oil seal lipsVaselineAs required
SEALANT
<Vehicles with AYC>
ItemsSpecified sealant
Torque transfer differential vent plugSemi-drying sealant: THREEBOND 1281B (460 g)
Torque transfer mechanism cover

REAR AXLE – Special Tools27-4
Tool UseName Number
AB
MB990241
A: MB990242
B: MB990244Rear axle shaft
puller
A: Puller shaft
B: Puller bar
Removal of drive shaft

Removal of rear hub assembly
MB991354Puller body
A: MB991017
B: MB990998
C: MB991000A, B: Front hub
remover &
installer
C: Spacer
Temporary fixing of unit bearing

Measurement of wheel bearing rotation
starting torque

Measurement of wheel bearing axial play
Use MB991000 (component
of MB990998) for the spacer.
MB990326Preload socket
Measurement of wheel bearing rotation
starting torque

Measurement of drive pinion preload
MB991406,
MB990635, or
MB991113Steering linkage
puller
Disconnection of ball joint

Removal of hub bolt
MB991460PlugPrevention of differential oil from being dis-
charged and entry of foreign matter <differen-
tial>
MB990988Side gear holding
tool setMeasurement of clutch plate preload <vehicles
without AYC>
MB990850End yoke holderRemoval and installation of companion flange

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-29
3-2 TORQUE TRANSFER MECHANISM
(1) Remove the drain plug to discharge the gear oil.
(2) Fit the drain plug and tighten it to the specified torque.
(3) Remove the filler plug and add the specified gear oil
up to the bottom end of the filler plug hole.
Specified gear oil:
MITSUBISHI GENUINE DIA QUEEN SUPER AYC
FLUID
Quantity used: 0.70
0
0.05dm3{0.700
0.05}
(4) Fit the filler plug and tighten it to the specified torque.
4. FLUID LEVEL CHECK
(1) Remove the maintenance lid located in the luggage
compartment.
(2) If the vehicle has been run, leave it for 5 min. or more
in an ordinary temperature (10
C to 30
C) to allow the
accumulator internal pressure to drop.
NOTE
If the ambient temperature is less than 10
C or less,
allow more time to leave the vehicle to stand idle.
(3) Check that the fluid level in the oil reservoir is in the
range between MAX and MIN.
(4) If the fluid level is lower than MIN, add the specified
fluid.
Specified fluid: MITSUBISHI DIA QUEEN ATF-SPII
(5) Reinstall the maintenance lid.
5. BLEEDING
(1) Lift up the vehicle.
(2) Remove the cap of the left bleeder screw on the torque
transfer differential and connect a vinyl hose.
(3) Gradually turn the steering wheel clockwise from the
straight-ahead position. At this time, loosen the left bleeder
screw and check that fluid is discharged with air.
(4) After air has been completely discharged, tighten the
bleeder screw.
Caution
While the system is being bled of air, add fluid as
necessary to ensure that it is left in the oil reservoir
during the entire procedure.
(5) Repeat steps (3) and (4) two to three times until no air
bubbles are recognized in the fluid that comes out. Then,
tighten the bleeder screw to the specified torque.
Tightening torque: 9 Nm {0.9 kgf
m}
(6) Perform steps (2) through (5) for the right bleeder screw.
Note, however, that the steering wheel should be turned
counterclockwise.
Filler plug
49 Nm {5.0 kgf
m}
Gear oil
Drain plug
49 Nm
{5.0 kgf
m}
Bleeder
screws Vinyl hose

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-30
(7) After the system has been completely bled of air, check
for the fluid level.
Caution
If the system is not completely bled of air, the hydraulic
unit could generate noise, degrading pump durability.
6. DIFFERENTIAL CARRIER OIL SEAL
REPLACEMENT
6-1 DIFFERENTIAL
(1) Remove the drive shaft. (Refer to p. 27-36.)
(2) Remove the oil seal from the differential carrier.
(3) Using the special tool, drive a new oil seal all the way
into position.
(4) Coat the oil seal lips and the drive shaft surface in contact
with the oil seal with multi-purpose grease.
(5) Replace the drive shaft circlip with a new one and mount
the drive shaft to the differential carrier. (Refer to P.27-36.)
(6) Check for correct wheel alignment. (Refer to GROUP
34 – On-vehicle Service.)
6-2 TORQUE TRANSFER MECHANISM
(1) Remove the drive shaft. (Refer to p. 27-36.)
(2) Remove the oil seal from the differential carrier.
(3) Using the special tool, drive a new oil seal all the way
into position.
(4) Coat the oil seal lips and the drive shaft surface in contact
with the oil seal with the specified grease.
Specified grease: Vaseline
(5) Replace the drive shaft circlip with a new one and mount
the drive shaft to the differential carrier. (Refer to P.27-36.)
(6) Check for correct wheel alignment. (Refer to GROUP
34 – On-vehicle Service.)MB990938
MB991115
MD998829
MD998812
MD998813

REAR AXLE – Rear Hub Assembly27-34
INSTALLATION SERVICE POINT
ADRIVE SHAFT NUT INSTALLATION
(1) Install the washer on the drive shaft in the direction shown
on the left.
(2) Using the special tool, tighten the drive shaft nut to the
specified torque.
Caution
Before torquing the drive shaft nut to specification,
do not apply vehicle weight to the wheel bearing.
(3) If, at this time, the split pin holes are not aligned, tighten
the nut further (within 255 Nm {26.0 kgf
m}), insert the
split pin in the first matching holes, and bend it securely.
INSPECTION
1. REAR WHEEL BEARING ROTATION STARTING
TORQUE
(1) Install the special tool to the rear hub assembly and tighten
it to the specified torque.
(2) Using the special tool, measure the wheel bearing rotation
starting torque.
Limit: 1.0 Nm {10.5 kgf
cm}
(3) The wheel bearing starting torque should be within the
limit and the hub should be free of binding or rough motion
when turned.
2. WHEEL BEARING AXIAL PLAY CHECK
(1) Check the wheel bearing for axial play.
Limit: 0.05 mm
(2) If the specified torquing range (196 to 255 Nm {20.0
to 26.0 kgf
m}) does not bring the wheel bearing axial
play into the limit, replace the rear hub assembly.
Washer
MB990767196 – 255 Nm
{20.0 – 26.0 kfg
m}
MB990326 MB991000
(MB990998)
Wood block 196 – 255 Nm
{20.0 – 26.0 kfg
m} MB991017
Wood block
Wood block
MB991017

REAR AXLE – Drive Shaft27-38
INSTALLATION SERVICE POINTS
ADRIVE SHAFT INSTALLATION
Caution
Use care not to allow the drive shaft splines to damage
the oil seal of the differential carrier.
BDRIVE SHAFT NUT INSTALLATION
(1) Install the washer on the drive shaft in the direction shown
on the left.
(2) Using the special tool, tighten the drive shaft nut to the
specified torque.
Caution
Before torquing the drive shaft nut to specification,
do not apply vehicle weight to the wheel bearing.
(3) If, at this time, the split pin holes are not aligned, tighten
the nut further (within 255 Nm {26.0 kgf
m}), insert the
split pin in the first matching holes, and bend it securely.
Washer
MB990767196 – 255 Nm
{20.0 – 26.0 kfg
m}

POWER PLANT MOUNT – Roll Stopper and Centermember32-2
ROLL STOPPER AND CENTERMEMBER
REMOVAL AND INSTALLATION
Caution
When tightening the portion marked with *, first
temporarily tighten it, then torque to specification
with the engine weight applied to the body.
1
2 34
5
Unit: Nm {kgf
m}
52 {5.3}*
22
34 {3.5}34 {3.5}
93 {9.5}
69 {7.0} 93 {9.5}
2
Removal steps
1. Front crossmember bar <vehicles
with 17’ wheels>
2. Bolt

B3. Front roll stopper bracket assembly

A4. Rear roll stopper bracket assembly
5. CentermemberNOTE
The conventional service procedures apply for the
installation service points.

FRONT SUSPENSION – Service Specifications / Special Tools33A-2
SERVICE SPECIFICATIONS
<EVOLUTION-IV>
ItemsStandard value
Toe-in mm–3
3
Camber–1
00’ ± 30’
(difference between right and left wheel: less than 30’)
Caster3
50’ ± 30’
(difference between right and left wheel: less than 30’)
Kingpin inclination13
25’
Lower arm ball joint rotation starting torque Nm {kgfcm}2.0 – 8.8 {20 – 90}
<EVOLUTION-V>
Same as EVOLUTION-IV except for following.
ItemsStandard value
Camber (selectable from 2 options)–1
00’ ± 30’ or –2
00’ ± 30’
(difference between right and left wheel: less than 30’)
Caster3
54’ ± 30’
(difference between right and left wheel: less than 30’)
Kingpin inclination14
18’
SPECIAL TOOLS
ToolNumberNameUse
A
BA: MB991237
B: MB991238A: Spring
compressor
body
B: Arm setCoil spring compression
MB991006Preload socketLower arm ball joint rotation starting torque
measurement

FRONT SUSPENSION – Lower Arm <EVOLUTION-IV>33A-5
LOWER ARM <EVOLUTION-IV>
REMOVAL AND INSTALLATION
Post-installation Operation
(1) Push the Dust Cover of the Lower Arm and Stabilizer
Link Ball Joint with a Finger to Check for Possible
Cracks or Damage.
(2) Wheel Alignment Check and Adjustment
12
3
45
6
Unit: Nm {kgfm}
39 {4.0}113 {11.5}
Molybdenum disulfide-base chassis
grease:
SHOWA SHELL SEKIYU SUNLITE
MB2, NISSEKI CLAKNOCK FL, or
equivalent
137 {14.0}
88 {9.0} 106 {10.8}*
6
Removal steps
1. Stabilizer link mounting nut
A2. Lower arm to knuckle coupling bolt
3. Bolt
4. Stabilizer bracket
A5. Bushing assembly
6. Lower arm assemblyCaution
The part marked with * should be first temporarily
tightened, then torqued to specification with the
vehicle on the ground in unloaded condition.
NOTE
Follow the conventional procedures for removal service
points.