roof MITSUBISHI LANCER EVOLUTION VI 1999 User Guide

BODY – Sunroof42-15
REMOVAL SERVICE POINTS
ASIDE DECORATION COVER REMOVAL
Remove the clips, and then remove the side decoration cover.
BDRAIN HOSE REMOVAL
Tie a cord to the end of the drain hose, and wind tape around
the tie until it is smooth. Then pull the drain hose out from
the passenger compartment.
CSUNROOF MOTOR REMOVAL
Caution
Always close the roof lid glass fully before removing
the sunroof motor. If the fully-closed positions of the roof
lid glass and the sunroof motor are not the same, the
sunroof will not operate properly.
INSTALLATION SERVICE POINTS
ASUNROOF MOTOR INSTALLATION
If the fully-closed position of the sunroof motor is incorrect,
set the motor to the fully-closed position by the procedure
given below before installing the motor.
1. Connect a circuit analyser between terminals (4) and (6)
of the motor connector.
2. Operate the motor until the position is reached at which
continuity switches from on to off or from off to on, and
then install the motor.
BDRAIN HOSE INSTALLATION
1. Tie the cord that was used during removal to the end
of the drain hose, and wind tape around it so that there
is no unevenness.
2. Pull the cord to pass through the drain hose
Clip
Side decoration cover
Drain hose
Cord
Cord
Drain hose

BODY – Sunroof42-16
3. Make the drain hose protrusion from the grommet as
shown in the illustration.
INSPECTION
ROOF LID GLASS OPERATION CURRENT CHECK
1. Remove the sunroof fuse and connect a circuit analyser
as shown in the illustration.
2. Press the sunroof switch to the ON position, and then
measure the operation current in the intervals between
the points when the sunroof starts to operate, when it
is fully open, when it is fully closed and when it is fully
tilted up.
Standard value: 7 A or less (at 20C)
3. If the operation current is outside the standard value,
check the following points.

Installation condition, warping or jamming of sunroof
assembly

Sticking of drive cable

Tilt of roof lid glass
Grommet
20–30 mm

BODY – Sunroof42-17
SUNROOF MOTOR CHECK
Check the direction of rotation of the drive gear when the
battery is connected to the connector.
Battery connection terminalDrive gear rotation
di ti12direction
Left
Right
LIMIT SWITCH CONTINUITY CHECK
1. Remove the limit switches from the sunroof motor, and
then check the operation of the limit switches.
Switch positionTerminal No.
4567
Limit switch 1ON
OFF
Limit switch 2ON
OFF
Limit switch 3ON
OFF
2. Check the identification colours. Then install the limit
switches as shown in the illustration.
SUNROOF SWITCH CONTINUITY CHECK
Switch positionTerminal No.
3456
Slide open
Off
Tilt up
Slide close, Tilt down
Left rotationDrive gear
Right rotation
(Red)(White)Limit switch 2, 3
ON
OFF
(Black)
(Black)(Blue)
Limit switch 1

BODY – Sunroof42-18
DISASSEMBLY AND REASSEMBLY
Sealant:
3M ATD Part No.8531 or 3M Part
No.8646, or equivalent
1 2
3 4
5
67
89 10
11
12
1110
NOTE
:Clip position
Disassembly steps
1. Side decoration cover
(Refer to P.42-15.)
2. Roof lid glass assembly
3. Sunroof motor
4. Drip rail assembly
5. Sunshade assembly
6. Cushion (B) assembly7. Drive unit assembly
8. Decoration link
9. Guide (A) assembly
10. Slider assembly
11. Rail cover assembly
12. Frame sub assembly

C-1
ELECTRICAL
WIRING
(R.H. DRIVE VEHICLES)
CONTENTS
GENERAL 3. . . . . . . . . . . . . . . . . . . . . . . . . .
WIRING HARNESS CONFIGURATION
DIAGRAMS 4. . . . . . . . . . . . . . . . . . . . . . . . .
ENGINE COMPARTMENT 4. . . . . . . . . . . . . . . .
DASH PANEL 8. . . . . . . . . . . . . . . . . . . . . . . . . . .
FLOOR AND ROOF 12. . . . . . . . . . . . . . . . . . .
LUGGAGE COMPARTMENT 14. . . . . . . . . . . .
SINGLE PART INSTALLATION
POSITION 16. . . . . . . . . . . . . . . . . . . . . . . . .
RELAY 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ECU 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SENSOR 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOLENOID AND SOLENOID VALVE 19. . . .
INSPECTION CONNECTOR 20. . . . . . . . . . . .
FUSIBLE LINK AND FUSE 20. . . . . . . . . . . . .
EARTH CABLE 21. . . . . . . . . . . . . . . . . . . . . . . .
EARTH 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CIRCUIT DIAGRAM 23. . . . . . . . . . . . . . . .
CENTRALIZED JUNCTION 23. . . . . . . . . . . . .
POWER DISTRIBUTION SYSTEM 24. . . . . .
STARTING SYSTEM 29. . . . . . . . . . . . . . . . . . .
IGNITION SYSTEM 30. . . . . . . . . . . . . . . . . . . .
CHARGING SYSTEM 31. . . . . . . . . . . . . . . . . .
MPI SYSTEM 32. . . . . . . . . . . . . . . . . . . . . . . . . .
COOLING SYSTEM 38. . . . . . . . . . . . . . . . . . . .
HEADLAMP 40. . . . . . . . . . . . . . . . . . . . . . . . . . .
TAIL LAMP, POSITION LAMP, LICENCE
PLATE LAMP AND LIGHTING MONITOR
BUZZER 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ROOM LAMP AND LUGGAGE
COMPARTMENT LAMP 45. . . . . . . . . . . . . . . .
IGNITION KEY CYLINDER ILLUMINATION
LAMP 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TURN-SIGNAL LAMP AND
HAZARD WARNING LAMP 48. . . . . . . . . . . . .
CONTINUED ON NEXT PAGE

– Dash Panel WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
B
C-10
DASH PANEL
B-38 (2) Sunlight sensor <vehicles with fully
automatic air conditioner>
B-39 (6) Air mix damper motor and potentiometer
<vehicles with fully automatic air condi-
tioner>
B-40 (3) Automatic compressor ECU
<vehicles with manual air conditioner>
B-41 (8) A/C switch
<vehicles with manual air conditioner>
B-42 (2) Blower switch illumination lamp <vehicles
with heater or manual air conditioner>
B-43 (6-B) Defogger switch <vehicles with heater or
manual air conditioner>B-44 (6) Body harness and roof harness combina-
tion <vehicles with sunroof>
B-45 (2-B) Diode (for keyless entry system circuit)
B-46 (2) Spare connector for fog lamp switch
<vehicles without fog lamp>
B-48 (14) J/C (2)
B-49 (14) J/C (3)
B-50 (14-L) J/C (4)
B-51 (21-Y) SRS-ECU
B-52 (16-B) Control harness and body harness
combination <vehicles with ABS>

– Floor and Roof WIRING HARNESS
CONFIGURATION DIAGRAMS
Connector
symbol
D
C-12
FLOOR AND ROOF
D-01 (20) Receiver
<vehicles with keyless entry system>
D-02 (2) Seat belt switch
D-03 (2) Front door switch (driver’s side)
D-04 (10) Body harness and fuel harness combina-
tion
D-05 (6) Body harness and rear door harness
(RH) combination
D-06 (18) Body harness and rear harness combina-
tion
D-07 (6) Sunroof switch
D-08 (2) Room lamp <vehicles with sunroof>D-09 (1) Map lamp
D-10 (18) Sunroof ECU
D-11 (2-GR) Room lamp <vehicles without sunroof>
D-12 (8) Sunroof motor
D-13 (3-B) Fuel gauge unit (sub)
D-14 (2-B) Rear speed sensor (LH)
<vehicles with ABS>
D-16 (6) Body harness and rear door harness (LH)
combination
D-17 (2) Front door switch (passenger’s side)
D-18 (6) Fuel gauge unit (main)

– Floor and Roof WIRING HARNESS
CONFIGURATION DIAGRAMS
NOTE
The connectors with framed
number are newly introduced.
C-13
D-19 (2-B) Rear speed sensor (RH)
<vehicles with ABS>
D-20 (3-B) Acceleration sensor <vehicles with ABS>
D-21 (1-B) Parking brake switch
D-27 (2) Body harness and rear harness combina-
tion <vehicles with AYC>D-31 (2) Water spray switch
D-32 (3-B) Acceleration sensor (lateral)
<vehicles with AYC>