wheel MITSUBISHI LANCER EVOLUTION VI 1999 Service Manual

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-36
(2) While this function is being disabled by the fail-safe
function, the forced activation of the hydraulic unit
can not be executed.
6. Check to ensure that the hydraulic pressure generated
by the hydraulic unit conforms to the standard value.
Standard value: 1.0 – 1.6 MPa
NOTE
During checking the hydraulic pressure, occasionally
replenish the oil reservoir with fluid so that it does not
become empty.
7. Check the hydraulic pressure of the clutch right side by
repeating the steps (4) through (6). At this time, however,
the special tool must be connected to the R port and
the blind plug or the R port of the removed hydraulic
unit hose assembly must be attached to the L port. Further,
the MUT-II must be operated in the forced activation mode
Item No. 14 (clutch right side operation check mode).
8. If the measured value exceeds the standard value, replace
the hydraulic unit.
9. Connect the hydraulic unit hose assembly to the hydraulic
unit and to the torque transfer differential and tighten
the flare nuts to the specified torque.
Specified torque: 34 Nm
10. Pour the specified fluid in the oil reservoir up to the MAX
mark. Then, bleed the system.
Specified fluid: Dia Queen ATF SP II or equivalent
Fluid amount used: Approx. 1

DIFFERENTIAL CARRIER OIL SEAL
REPLACEMENT
DIFFERENTIAL
1. Remove the drive shaft.
2. Remove the oil seal from the differential carrier.
3. Using the special tool, drive a new oil seal all the way
into position.
4. Coat the oil seal lips and the drive shaft surface in contact
with the oil seal with multi-purpose grease.
5. Replace the drive shaft circlip with a new one and mount
the drive shaft to the differential carrier.
6. Check for correct wheel alignment.
TORQUE TRANSFER MECHANISM
1. Remove the drive shaft.
2. Remove the oil seal from the differential carrier.
3. Using the special tool, drive a new oil seal all the way
into position.
4. Coat the oil seal lips and the drive shaft surface in contact
with the oil seal with the specified grease.
Specified grease: Vaseline
5. Replace the drive shaft circlip with a new one and mount
the drive shaft to the differential carrier.
6. Check for correct wheel alignment.
MB990938
MB991115
MD998829
MD998812
MD998813

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-37
WHEEL SPEED SENSOR OUTPUT VOLTAGE
MEASUREMENT <VEHICLES WITHOUT ABS>
1. Lift up the vehicle and release the parking brake.
2. Disconnect the AYC-ECU harness connector and take
measurements on the harness side connector.
Caution
Insert the probe from the harness side with the double
lock of the connector unlocked. Inserting it to the
terminal side could result in poor contact.
3. Turn the wheel to be tested at about 1/2 to one
revolution/sec. and check for the output voltage using
a circuit tester (AC mV range) or oscilloscope.
Terminal nos.
Front LHFront RHRear LHRear RH
7698
20192221
Output voltage:
When circuit tester is used: 70 mV or more
When oscilloscope is used: 200 mVp-p or more
(4) If the output voltage is lower than the above value, it
is probably attributable to the following faults. Check or
replace the wheel speed sensor as necessary.

Excessive clearance between the pole piece and rotor
of the wheel speed sensor

Defective wheel speed sensor
Waveform Check Using Oscilloscope
Check the harness and connector of the wheel speed sensor
for connection. Then, use an oscilloscope to check for output
voltage waveform of each sensor as follows.
Start the engine and monitor the sensor by turning the wheel;
for a driving wheel, let it turn by shifting into the 1st gear
and for a driven wheel turn it manually at a constant speed.
NOTE
(1) Waveform may be observed by actually running the
vehicle.
(2) The output voltage is low when the wheel speed remains
low and builds up as the wheel speed increases.
AYC-ECU connector harness side
When turned manually
At idle (5 to 6 km/h)
1st gear

REAR AXLE – On-vehicle Service <Vehicles with AYC>27-38
Waveform Observation Points
SymptomProbable causeAction
Waveform amplitude is too small, or no
waveform.Defective wheel speed sensorReplace sensor.
Waveform amplitude varies greatly. (No
problem ifthe smallest amplitude is 100
Excessive axle hub lateral and radial runoutReplace hub.
problem if the smallest amplitude is 100
mV or more)Poor AYC-ECU groundingRepair.
Noise on waveform or disturbed
waveform
Open-circuited sensorReplace sensor.
waveform
Open-circuited harnessRepair harness.
Improperly mounted wheel speed sensorCorrect sensor installation.
Missing or collapsed ABS rotor toothReplace ABS rotor.
Caution
Since the wheel speed sensor cable follows the movement of the front or rear suspension, it
may be open-circuited only when the vehicle is run on rough roads and not on ordinary road.
The wheel speed sensor output voltage waveform should therefore be checked also by rocking
the sensor harness so that driving on rough roads may be simulated.
ACTION WHEN BATTERY RUNS OUT
When the engine is started using a booster cable where the
battery has completely run down and you attempt to start
the vehicle without waiting for the battery to recover a certain
charge, the engine can misfire and you just cannot start to
move it. In such cases, charge the battery sufficiently; or,
remove the AYC fusible link from the engine compartment
relay box to make AYC inactive before attempting to start
the vehicle. When the fusible link is removed, the AYC warning
lamp lights up. After the battery has been recharged, fit the
fusible link back again and start the engine to ensure that
the AYC warning lamp is off.AYC fusible link

REAR AXLE – Sensor Relay <Vehicles with AYC>27-41
SENSOR RELAY <VEHICLES WITH AYC>
REMOVAL AND INSTALLATION
Caution: SRS
For vehicles with SRS, before removal of air bag module and clock spring, refer to GROUP 52B
– Service Precautions and Air Bag Module and Clock Spring.
12
3
4
Steer sensor removal steps

Steering wheel and column cover
A1. Steer sensorAcceleration sensor and AYC relay
removal
2. Longitudinal acceleration sensor
3. Lateral acceleration sensor
4. AYC relay
NOTE
For the wheel speed sensor, refer to GROUP 35B.
REMOVAL SERVICE POINT
ASTEER SENSOR REMOVAL
Remove the steer sensor from the column switch.
Caution
(1) A photocoupler is used as the steer sensor. Use care
not to allow dust or grease to be on the sensor.
(2) Do not bend or dirty with grease the slit plate on
the column switch side.Slit plate
Steer sensor

FRONT SUSPENSION – General / Lower Arm <EVOLUTION-VI>33A-1
GROUP 33A
FRONT SUSPENSION
GENERAL
OUTLINE OF CHANGE

The installation method of the ball joint between the knuckle and the lower arm has been changed,
and accordingly the removal and installation procedures of the lower arm have been revised.
<EVOLUTION-VI>
LOWER ARM <EVOLUTION-VI>
REMOVAL AND INSTALLATION
Caution
The part marked with * should be first temporarily tightened, then torqued to specification with the vehicle
on the ground in unloaded condition.
Post-installation Operation

Push the Dust Cover of the Lower Arm and Stabilizer Link Ball Joint with a Finger to Check for Possible Cracks or Damage.

Wheel Alignment Check and Adjustment
1
2
3
4
5
6
39 Nm
106 Nm*
5
98 – 118 Nm
74 – 87 Nm88 Nm
137 Nm
Removal steps
1. Stabilizer link mounting nut
2. Bolt
3. Stabilizer bracket
A4. Bushing assembly
5. Lower arm assembly6. Lower arm bracket assembly
NOTE
Follow the conventional procedures for installation service
points.

BASIC BRAKE SYSTEM – Brake Pedal35A-4
BRAKE PEDAL <L.H. DRIVE VEHICLES>
REMOVAL AND INSTALLATION
Pre-removal Operation

Instrument Under Cover Removal

Steering Column Assembly Removal
(Refer to GROUP 37A – Steering Wheel and Shaft.)

Accelerator Pedal RemovalPost-installation Operation

Accelerator Pedal Installation

Steering Column Assembly Installation
(Refer to GROUP 37A – Steering Wheel and Shaft.)

Instrument Under Cover Installation

Brake Pedal Adjustment (Refer to P.35A-2.)
29 Nm
12 Nm
14 Nm
1 2
3
4 5
67 813 Nm
11
910
8 9
Removal steps
1. Stop lamp switch connector
2. Stop lamp switch
3. Snap pin
4. Clevis pin
5. Brake pedal shaft bolt
6. Brake pedal7. Brake pedal pad
8. Brake pedal return spring
9. Bushing
10. Pipe
11. Pedal support member

37A-1
STEERING
CONTENTS
GENERAL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outline of Change 2. . . . . . . . . . . . . . . . . . . . . . . . .
STEERING WHEEL AND SHAFT* 2. . . . . . . .
POWER STEERING GEAR BOX* 5. . . . . . . . .
WARNINGS REGARDING SERVICING OF SUPPLEMENTAL RESTRAINT SYSTEM (SRS) EQUIPPED VEHICLES
WARNING!
(1) Improper service or maintenance of any component of the SRS, or any SRS-related component, can lead to personal
injury or death to service personnel (from inadvertent firing of the air bag) or to the driver and passenger (from rendering
the SRS inoperative).
(2) Service or maintenance of any SRS component or SRS-related component must be performed only at an authorized
MITSUBISHI dealer.
(3) MITSUBISHI dealer personnel must thoroughly review this manual, and especially its GROUP 52B – Supplemental
Restraint System (SRS) before beginning any service or maintenance of any component of the SRS or any SRS-related
component.
NOTE
The SRS includes the following components: SRS-ECU, SRS warning lamp, air bag module, clock spring and interconnecting
wiring. Other SRS-related components (that may have to be removed/installed in connection with SRS service or maintenance) are
indicated in the table of contents by an asterisk (*).

STEERING – General / Steering Wheel and Shaft37A-2
GENERAL
OUTLINE OF CHANGE

The service procedures for left-hand drive vehicles have been established as described below. The
service procedures for components not mentioned below are the same as for the preceding models.
STEERING WHEEL AND SHAFT <L.H. DRIVE VEHICLES>
REMOVAL AND INSTALLATION
CAUTION: SRS
For vehicles with SRS, before removal of air bag module, refer to GROUP 52B – Service Precautions and
Air Bag Module and Clock Spring.
Pre-removal Operation
Instrument Under Cover RemovalPost-installation Operation

Instrument Under Cover Installation

Checking Steering Wheel Position with Wheels
Straight Ahead
<Vehicles without SRS>
5 Nm
17 Nm11 Nm
<Vehicles with SRS>
10
98 431
532
41 Nm
25 Nm
6
25 Nm41 Nm
7
9 Nm
Section A – A Section B – B
Claw
: Claw position
AB 4
5
AB
11 Nm 21 Nm Standard bolt Earth bolt
NOTE
4
5
Claw
Removal steps
1. Horn pad <Vehicles without SRS>
2. Air bag module
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
A3. Steering wheel
4. Upper column cover
5. Lower column coverA6. Column switch
<Vehicles without SRS>
A7. Clock spring and column switch
(Refer to GROUP 52B – Air Bag
Module and Clock Spring.)
8. Steering shaft assembly
9. Band
10. Steering cover assembly

STEERING – Steering Wheel and Shaft37A-3
REMOVAL SERVICE POINT
ASTEERING WHEEL REMOVAL
INSTALLATION SERVICE POINT
ACLOCK SPRING AND COLUMN SWITCH / COLUMN
SWITCH INSTALLATION
Tighten the screws in an alphabetical order.
DISASSEMBLY AND REASSEMBLY
1
2
3 4
Disassembly steps
AA1. Special bolt
A2. Steering lock bracket
A3. Steering lock cylinder
4. Steering shaft
MB990803
A
BC

STEERING – Steering Wheel and Shaft37A-4
DISASSEMBLY SERVICE POINT
ASTEERING LOCK BRACKET / STEERING LOCK
CYLINDER REMOVAL
If it is necessary to remove the steering lock cylinder, use
a hacksaw to cut the special bolts at the steering lock bracket
side.
REASSEMBLY SERVICE POINT
ASTEERING LOCK CYLINDER/STEERING LOCK
BRACKET / SPECIAL BOLT INSTALLATION
1. When installing the steering lock cylinder and steering
lock bracket to the column tube, temporarily install the
steering lock in alignment with the column boss.
2. After checking that the lock works properly, tighten the
special bolts until the head twists off.
Caution
The steering lock bracket and bolts must be replaced
with new ones when the steering lock is installed.
Steering lock bracket
Steering lock cylinder