engine MITSUBISHI LANCER EVOLUTION VIII 2004 User Guide

ENGINE (4G6) – INT
AKE / EXHAUST SYSTEM (6 M/T)17
12 Exhaust silencer
A tailpipe with builtin soundabsorbing material has been adopted, in order to increase the silencing effect.
Structural diagram
Main exhaust
silencer
Tailpipe
(with builtin soundabsorbing material)Crosssection
A–A
Sound
absorbing
material

ENGINE (4G6) – GENERAL, BASE ENGINE (6 M/T)18
Control system (6M/T)
The following changes have been made, based on the control system in the 4G63DOHCT/C engine fitted in the current
Lancer Evolution VIII.
* Addition of wastegate solenoid valve (1 valve –> 2 valves)
System Block Diagram
Air flow sensor (AFS)
Air temperature sensor
Atmospheric pressure sensor
Water temperature sensor
Throttle position sensor (TPS)
A/C switch
A/C load signal
Cam position sensor
Crank angle sensor
Alternator FR terminal
Vehicle speed sensor
Power steering fluid pressure
switch
Knock sensor
Intercooler water spray (auto)
Intercooler water spray (manual)
O
2sensor
Ignition switch –IG
Ignition switch –STPower supplyEngine ECU
Fuel injection control
Idle speed control (ISC)
Ignition timing control
Engine control relay control
Fuel pump relay control
A/C relay control
Fan motor control (radiator)
Fan relay control (A/C
condenser)
Alternator control
Air flow sensor filter reset
control
Fuel pressure control
Supercharging pressure
control
Secondary air controlIntercooler water spay control
Engine warning light control
O
2sensor heater control
Purge control
Diagnosis output
RAM data transmissionNo. 1 indicator
No. 2 indicator
No. 3 indicatorNo. 4 indicator
ISC servo (stepper motor)
Ignition coil A (No.1 – No.4)
Ignition coil B (No.2 – No.3)
Engine control relay
Fuel pump relay 2
Fuel pump relay 3
A/C relay
Fan controller (radiator fan)
Fan motor relay (HI, LOW)
(A/C condenser)
Alternator G terminal
Air flow sensor
Fuel pressure control valve
No. 1 wastegate solenoid valve
No. 2 wastegate solenoid valve
Secondary air control solenoid
valve
Intercooler water spray relay
Intercooler water spray lamp
Tachometer
Engine warning lights O
2sensor heater
Purge control solenoid valve
Diagnosis output terminal
Diagnosis output terminal (for
MUTII)

ENGINE (4G6) – GENERAL, BASE ENGINE (6 M/T)19
1. O2 sensor2. Air flow sensor3. Air intake sensor4. Throttle position
sensor
5. Cam position sensor6. Crack angle sensor7. Atmospheric pressure
sensor
8. Water temperature
sensor
9. Knock sensor•Power supply
• Ignition switch IG
•Ignition switch ST
•Vehicle speed sensor
• A/C switch
1. Injector2. ISC servo (stepper
motor)
3. Fuel pressure control
solenoid valve
4. No.1 wastegate solenoid
valve
5. No.2 wastegate solenoid
valve
6. Purge control solenoid
valve
7. Secondary air control
solenoid valve•Engine control relay
•Fuel pump relay 2, 3
•A/C relay
•Ignition coil
• Fan controller
Engine ECU
6. Purge control
solenoid valveCanister
7. Secondary air
control solenoid valveFrom fuel tank
Secondary
air valveBypass
valve
1. O2sensor
3. Fuel pressure
control solenoid valve
4. Throttle
position
sensor
7. Atmospheric pressure
sensor
3. Air intake
sensor2. Air flow sensor
4. No.1
wastegate
solenoid valve
5. No.2 wastegate
solenoid valve
Only operates on 6M/TWastegate actuatorFuel pressure
regulator
1. Injector5.Cam position sensor8.Water temperature sensor
9.Knock sensor
Crack angle sensor
Catalytic converter Air
intakeCheck
valve
2. ISC servo
Vacuum
tank
From fuel
pump To fuel
tank
Control system diagram

ENGINE (4G6) – CONTROL SYSTEM (6 M/T)110
1. Supercharging pressure control
The maximum torque has been increased, compared to the 4G63DOHCT/C engine in the current Lancer Evolution VIII, by
installing an additional wastegate solenoid valve (increased from 1 to 2 valves).
By adding a parallel No.2 wastegate solenoid valve to the previous system, provides extra relief capacity for the pressure
applied to the wastegate actuator thus increasing the range of supercharging pressure..
The engine ECU raises the supercharging pressure even further, thus raising the maximum torque, by driving the No.2
wastegate solenoid valve when the engine approaches maximum torque.
The No.1 wastegate solenoid valve is essentially controlled in the same way as previously.
Air flow
sensor
Knock
sensor
Engine
ECUBatterySecondary air
control solenoidvalve
Secondary
air valve
Ignition
switch
Air
intakeBypass valveVacuum tank
Intercooler
Turbocharger
Wastegate
actu
ator No. 1
wastegate
solenoid
valve
No. 2 wastegate
solenoid valve Crank angle
sensor

81REFERENCE MATERIAL – MAIN SPECIFICATIONS
SECTION 8
REFERENCE MATERIAL
CONTENTS
Main specifications.................................81
Detailed specifications ...........................84Main equipment ......................................86
Cold climate specifications ...................88
Main Specifications
These Main Specifications are based on submitted data, and may therefore differ from the actual equipment.
The
symbol indicates specifications which have changed from the previous model.
Vehicle name and modelMitsubishi GHCT9A
Chassis name and typeMitsubishi CT9A
ManufacturerMitsubishi Motor Corporation
CategoryNormal
UsePassenger
Body shapeSaloon
Engine type4G63
Capacity cc1997
GHCT9A
GHCT9AItem
SNDFZSJDFZSJGFZ
Classification No.È079, 080, 085, 086,
091, 092, 097, 098083, 084, 089,
090, 095, 096,
099~102105, 106, 109,
110, 113, 114,
117, 118119
Vehicle length mm4490
Vehicle width mm1770
Vehicle height mm1450
Wheelbase mm2625
Front15001515¨¨
Dimensions
Track mm
Rear15001515¨¨
WeightSee weight chart
Left50˚PerformanceMax.
angle ofstability
Right50˚
Wheel alignmentFront 2 drive – Rear 2 drive
Front
Other
Tyre
size
Rear
205/65R15 94H235/45ZR17¨¨
Note :
See Weight Chart for relationships between classification numbers and equipment.

REFERENCE MA
TERIAL – MAIN SPECIFICATIONS / DETAILED SPECIFICATIONS84
GHCT9AItem
SNDFZSJDFZSJGFZ
Minimum ground clearance m0.140¨¨
Max. speed (estimated) km/h180¨¨
Fuel consumption km/l (10/15 mode)9.69.7¨
Braking distance m (initial speed in
km/h) È49 (100)
[Vehicle with15" brakes]
43 (100)
[Vehicle with17" brakes]¨¨
Performance
Min. turning radius m5.9¨¨
Bore x stroke mm85.0 X 88.0¨¨
Compression ratio8.8 (Unleaded
Premium)¨¨
Max. output net [k/W r.p.m.]206 / 6500
(net)¨¨
Max. torque N•m/rpm.392 / 3500
(net)400 / 3500
(net) Ȩ
OpenBTDC 21˚BTDC 17˚
ȨIntake
ClosedABDC 59˚ABCD 63˚
Ȩ
OpenBBDC 58˚¨¨
Engine
Valve or
port timing
Exhaust
ClosedATDC 18˚¨¨
Fuel tank capacity (litres)50¨55
Type and performance of ignition
equipmentElectronic:
20˚~ 45˚¨¨
Type of spark plugsIGR7A,
IGR7AG,S22PRA7,VW22PRDA7¨¨
Battery capacity Ah34 (5), 48 (5)
or 52 (5)¨¨
Electrical
Equipment
Alternator output VA12 – 58, 90,
100 or 105¨¨
Detailed Specifications
These Detailed Specifications are based on submitted data, and may therefore differ from the actual equipment.
The
symbol indicates specifications which have changed from the previous model.

REFERENCE MA
TERIAL – MAIN EQUIPMENT86
Main Equipment
The “” symbol indicates standard equipment, and the “” symbol indicates a manufacturer’s option. The equipment may change, depending on the time of manufacture.
4WD
RSGSR
Equipment
5M/T6M/T
Aluminium turbollr
Intercooler water spray systemlll
W/out Intercooler water spray systemrr
Engine
Engine oil coolerlll
5speed manual (short stroke, high gear
ratio)l
6speed manual (short stroke)ll
Gear leverLeather
Front LSDHelical
Rear LSDMechanical
l
lll
Active Centre Differential (ACD)lll
Power
Train
Active Yaw Control Differential (AYC)rll
Bilstein shock absorbersrrl
Front strut tower barslll
205/65R15 94HlTyres
235/45ZR17rll
T125/70D16lSpare
tyre
T125/70D17rll
Steel (5hole)
(Offset : 46 mm)
(PCD:
114.3mm)15inch
¥ 6.0JJ
silverl
17inch
¥ 8.0JJrllSteel (5hole)
(Offset : 38 mm)
(PCD:114.3mm)
17inch
¥ 8.0JJ
(BBS)
rrr
Steel (5hole)
(Offset : 40 mm)
(PCD:
114.3mm)4.0T•
16inchl
Wheel
Steel (5hole)
(Offset : 30 mm)
(PCD:114.3mm)4.0T•
17inch
rll
Centre capBlackl
Power steeringlll
MOMOllSteering wheel (leather
type ; 3spoke; airbag)
MOMO
(black
spokes)
rrl
Tilt steering mechanism
Full cover
lll
Release switch
(gloss)
Parking brake
lever
Leather grip
l
15inch ventilated
disclFront
17inch ventilated
disc (BREMBO)rll
15inch ventilated
disc (drum in)l
Drive
Control
Brake
Rear
16inch ventilated
disc (drum in)(BREMBO)
rll
Note:
In the wheel columns, “PCD” is an abbreviation of “Pitch
Circle Diameter”, referring to the diameter of the pitch circle
of the installation holes.
4WD
RSGSR
Equipment
5M/T6M/T
4 ABS (sports ABS)rll
Pressure control valve (PCV)l
Drive
Control
Electronic Brake Force Distribution
System (EBD)rll
Central door lockingrrl
Boot lid openerlll
Fuel filler flap opener
Child protection
lll
Multimode keyless entryl
BlackllOuter door handles
Body colourl
Inside door handlesColouredlll
Power windows with safety mechanismsrrl
Windscreen (laminated glass)Green
Front door windows (UV absorbing
glass)lll
Greenll
Green, with sun
shadel
Rear window
glass (with
heating element)
Privacy glassr
GreenlllRear door
windows
Privacy glassr
GreenlllRear static
windows
Privacy glassr
BonnetAluminiumAir outlet
WingAluminium
RoofAluminium
lll
Body
Rear end crossbarll
Exclusive
front bumperBody colour
Exclusive
rear bumperBody colour
Windscreen
Rear window
Pillar, roof
Mouldings
(black)
Belt line
lll
Manual type (black)llDoor mirror
Electric stowable
remote control door
mirror (body colour)l
Front air damExclusive
extension
Rear air dam
lll
Exterior
Rear spoiler (large size)lll

REFERENCE MA
TERIAL – MAIN EQUIPMENT, COLD CLIMATE SPECIFICATIONS88
4WD
RSGSR
Equipment
5/MT6/MT
ABSrll
SRS airbags
Fuel level
Parking brake
Charge
Brake fluid
Engine check
Warning
lights
Door not properly closed
Lighting monitor warningBuzzer
Ignition key reminder warning
lll
Fixed time
intermittentll
Variable
intermittent(speed
sensitive)l
Windscre
en wipers2 speed
Mist spray
Equip
ment
Windscreen washer (synchronized with
wiper, 4jet)
lll
4WD
RSGSR
Equipment
5/MT6/MT
Rear
windowwiper /
washerFixed time intermittent,
synchronized with (R) gearpositionl
AM/FM tuner radio + MD player
+ DVDMMCS (DVD navigation
Mitsubishi MultiCommunication
System)r
Roof aeriallll
Roof and window aerial (diversity
aerial)r
W/out audiolll
Audio
parts
6 speakers (2 DIN compatible)r*3
Digital clock
Immobiliser system
lll
Manual heater
Air conditioning kit
ll
Equip
ment
Air
conditioning
Fully automatic air
conditioningl
Notes:
*3: Brackets for an aerial and radio are installed as standard.
Cold Climate Specifications
4WD
RSGSR
Equipment
5M/T6M/T
Battery
Weather strip silicon coating
Rear seat heater duct
Cold Climate Specification label
rrr
Door mirrors with heating elementsr

TitleNo.Issue dateTitleNo.Issue date
New model manualsBody Service Manuals
•Mirage, Lancer1036F3010/1995•Mirage, Lancer
(supplement)1036F528/1996
•Mirage, Lancer1036F311/1996•Lancer Sedia1036K505/2000
•Mirage, Lancer1036F328/1996•Lancer Sedia
(supplement)1036K517/2000
•Mirage, Lancer1036F337/1997•Lancer Evolution VII
(supplement)1036K525/2001
•Lancer1036F341/1998•Lancer Sedia
(supplement)1036K5310/2001
•Mirage, Lancer1036F3510/1998
•Lancer1036F361/1999
•Lancer1036F3712/1999
•Lancer Sedia1036K305/2000
•Lancer Sedia1036K317/2000
•Lancer Evolution VII1036K321/2001Wiring layout diagram
Service Manuals
•Lancer Sedia1036K335/2001•Lancer Evolution VIII1036K771/2003
•Lancer Sedia1036K345/2001•Lancer Evolution VII
MR (Supplement)1036K802/2004
•Lancer Evolution VII1036K351/2001
•Lancer Sedia1036K365/2002
•Lancer Evolution VIII1036K371/2003
•Lancer1036K382/2003
•Lancer1036K3912/2003
•Lancer Evolution VIII MR1036K402/2004
Service ManualsEngine Service Manuals
•Lancer Sedia1036K005/2000•4G6 Engine1039G461/2001
•Lancer Sedia1036K017/2000•4G6 Engine1039G631/2003
•Lancer Evolution VII
(supplement)1036K021/2001
•Lancer Sedia (supplement)1036K035/2001
•Lancer Sedia (supplement)1036K0410/2001Transmission Service
Manuals
•Lancer Evolution VII
(supplement)1036K051/2002•W5M51 Manual
Transmission1039M171/2001
•Lancer Sedia (supplement)1036K065/2002•W5M51Manual
transmission(Supplement)1039M221/2003
•Lancer Evolution VII
(supplement)1036K071/2003•W6MAA Manual
transmission1039M231/2003
•Lancer (supplement)1036K082/2003
•Lancer (supplement)1036K0912/2003
•Lancer Evolution VIII MR1036K102/2004
Related information
Precautions to be taken when servicing vehicles with seatbelts fitted with SRS Airbag and Pretensioners
Precautions
1. Incorrect inspection or servicing of SRS airbag and pretensioner fitted seatbelt parts, as well as any related
components, could lead to major damage or nonoperation as a result of sudden, unintentional operation of SRS
airbag and pretensioner fitted seatbelts (incorrect deployment).
2.In cases where heating from painting processes occurs, the SRSECU, driver side airbag module, passenger side
airbag module, pretensioner fitted seatbelts, and cross springs, should be removed.
• 93°C and above: SRSECU, driver side airbag module, passenger side airbag module, cross springs
• 90°C and above: pretensioner fitted seatbelts3.Inspections and servicing of SRS airbag and pretensioner fitted seatbelt parts and any related components must,
without fail, be done by a Mitsubishi Motors authorized dealer.
4. Inspections and servicing of SRS airbag and pretensioner fitted seatbelt parts and any related components must be
done paying scrupulous attention to the relevant service manual (particularly in the case of Group 52B – SRS
airbags).

01
GENERAL MODEL LINEUP , APPLIED VEHICLES
SECTION 0
GENERAL
CONTENTS
Model lineup
Note
= Continued model
Applied vehicles
GHCT9A: CT9A0300001 ~
Model lineup...........................................01
Applied vehicle numbers .......................01Main specifications.................................02
ModelVersion’04 ModelGradeEngine ModelTransmissionFuel System
GHCT9ASNDFZ
SJDFZ
SJGFZ

RS
RS
GSR4G63
(2 000 DOHC 16 valve
intercooler turbo)W5M51 (4WD, 5M/T)
W6MAA (4WD, 6 M/T)MPI