brakes MITSUBISHI LANCER EVOLUTION VIII 2004 Workshop Manual

REFERENCE MA
TERIAL – MAIN SPECIFICATIONS / DETAILED SPECIFICATIONS84
GHCT9AItem
SNDFZSJDFZSJGFZ
Minimum ground clearance m0.140¨¨
Max. speed (estimated) km/h180¨¨
Fuel consumption km/l (10/15 mode)9.69.7¨
Braking distance m (initial speed in
km/h) È49 (100)
[Vehicle with15" brakes]
43 (100)
[Vehicle with17" brakes]¨¨
Performance
Min. turning radius m5.9¨¨
Bore x stroke mm85.0 X 88.0¨¨
Compression ratio8.8 (Unleaded
Premium)¨¨
Max. output net [k/W r.p.m.]206 / 6500
(net)¨¨
Max. torque N•m/rpm.392 / 3500
(net)400 / 3500
(net) Ȩ
OpenBTDC 21˚BTDC 17˚
ȨIntake
ClosedABDC 59˚ABCD 63˚
Ȩ
OpenBBDC 58˚¨¨
Engine
Valve or
port timing
Exhaust
ClosedATDC 18˚¨¨
Fuel tank capacity (litres)50¨55
Type and performance of ignition
equipmentElectronic:
20˚~ 45˚¨¨
Type of spark plugsIGR7A,
IGR7AG,S22PRA7,VW22PRDA7¨¨
Battery capacity Ah34 (5), 48 (5)
or 52 (5)¨¨
Electrical
Equipment
Alternator output VA12 – 58, 90,
100 or 105¨¨
Detailed Specifications
These Detailed Specifications are based on submitted data, and may therefore differ from the actual equipment.
The
symbol indicates specifications which have changed from the previous model.

MANUAL TRANSMISSION TROUBLESHOOTING2211
Code No.52 Longitudinal G sensor systemAssumed cause of concern
At 10kph or over, with ABS and brakes not applied, code No.
52 is output in cases where G sensor indicates higher than
specified value.• Harness, connector malfunction
• Longitudinal G sensor malfunction
• ABSECU malfunction <ACD+AYC fitted vehicles>
• 4WDECU malfunction
Remarks*2: refer to ’011 Lancer Evolution VII Service Manual (No.1036K02)
MUTII/III Service data
• No.14 longitudinal sensor voltage
OK:P.2232 Refer to (Service Data List)*2
OK > Intermittent malfunction
Longitudinal G sensor check (refer to P.2232)
*2
NG > replace
Measurement at C38 4WDECU connector
• ECU terminal voltage measurement
• Ignition switch: ON
• Voltage between 23 – earth
OK:2.4 – 2.6V (when vehicle is standing on flat
ground)
Connector check:C38
NG > repair
MUTII/III Service data
• No.14 longitudinal sensor voltage
OK:P.2232 Refer to (Service Data List)*2
NG > Replace 4WDECU
OK > Intermittent malfunction
Connector check:C38, D29, C20, B109
<ACD+AYC fitted vehicles> C38, C20, D29 <ACD
fitted vehicles> NG > repair
Check harness between longitudinal G sensor – 4WD
ECU
•Check to see if output wire is broken, earth, or
damaged
Check harness between longitudinal G sensor – ABS
ECU
<ACD+AYC fitted vehicles>
MUTII/III Service data
• No.14 longitudinal G sensor voltage
OK:Refer to P.2232 (Service Data List)*2
NG > Refer to Group 35C – Troubleshooting*2
<ACD+AYC fitted vehicles> or replace 4WDECU
OK > intermittent malfunction
NG
OK
OK
OK
NG
OK
OK

MANUAL TRANSMISSION TROUBLESHOOTING2213
Code No.57 Lateral G sensor systemAssumed cause of concern
At 10kph or over, with ABS and brakes not applied, code No.
57 is output in cases where G sensor indicates higher than
specified value.• Harness, connector malfunction
• Longitudinal G sensor malfunction
• ABSECU malfunction <ACD+AYC fitted vehicles>
• 4WDECU malfunction
Remarks*2: refer to ’011 Lancer Evolution VII Service Manual (No.1036K02)
MUTII/III Service data
• No.15 longitudinal sensor voltage
OK:P.2232 Refer to (Service Data List)*2
OK > Intermittent malfunction
Lateral G sensor check (refer to P.2220)
*2
NG > replace
Measurement at C38 4WDECU connector
•ECU terminal voltage measurement
• Ignition switch: ON
•Voltage between 11 – earth
OK:2.4 – 2.6V (when vehicle is standing on flat
ground)
Connector check:C38
NG > repair
MUTII/III Service data
•No.15 lateral sensor voltage
OK:P.2232 Refer to (Service Data List)*2
NG > Replace 4WDECU
OK > Intermittent malfunction
Connector check:C38, D31, C20, B109
<ACD+AYC fitted vehicles> C38, C20, D31 <ACD
fitted vehicles> NG > repair
Check harness between lateral G sensor – 4WDECU
•Check to see if output wire is broken, earth, or
damaged
Check harness between lateral G sensor – ABSECU
• Check to see if output wire earth or damaged
NG > repair
MUTII/III Service data
•No.15 lateral G sensor voltage
OK:Refer to P.2232 (Service Data List)*2
NG > Refer to Group 35C – Troubleshooting*2
<ACD+AYC fitted vehicles> or replace 4WDECU
OK > intermittent malfunction
NG
NG
OK
OK
OK
OK
OK