MITSUBISHI LANCER SPORTBACK 2013 8.G Owners Manual

7-70 Vehicle care and maintenance
7
3. Turn the socket (D) counterclockwise to remove it.
4. Pull the bulb out of the socket.
Ty p e 2BK0151000US.book 70 ページ ２０１２年３月２９日　木曜日　午後６時８分

Vehicle care and maintenance
7-71
7
5. To install the bulb, perform the removal steps in reverse.
Front turn signal lights
N00943400325
1. Remove the clips (A) and clips (B), then remove the duct
(C) and the upper cover (D).Except for vehicles with turbocharger
BK0151000US.book 71 ページ ２０１２年３月２９日　木曜日　午後６時８分

7-72 Vehicle care and maintenance
7
2. Remove the entire socket and bulb assembly (E) by turn-
ing it counterclockwise.
Vehicles with turbocharger
*- Front of the vehicle
BK0151000US.book 72 ページ ２０１２年３月２９日　木曜日　午後６時８分

Vehicle care and maintenance
7-73
7
3. Remove the bulb by pulling it out.
4. To install the bulb, perform the removal steps in reverse.
Front fog lights (Type 1)
(if so equipped)
N00943600734
1. Remove the screw (A) and pull the cover out.
BK0151000US.book 73 ページ ２０１２年３月２９日　木曜日　午後６時８分

7-74 Vehicle care and maintenance
7
2. Remove the screws (B) and pull the entire light unit out.
NOTE
When unfastening the screws, be careful not to mistakenly
move the beam position adjustment screw (C).
BK0151000US.book 74 ページ ２０１２年３月２９日　木曜日　午後６時８分

Vehicle care and maintenance
7-75
7
3. Push the connector (D) to disconnect and remove the fog
light. 4. Remove the bulb assembly (E) by turning it counterclock-
wise.
5. To install the bulb, perform the removal steps in reverse.
BK0151000US.book 75 ページ ２０１２年３月２９日　木曜日　午後６時８分

7-76 Vehicle care and maintenance
7
NOTE
When mounting the cover, align the hooks (F) on the
cover with the hole in the body.
CAUTION
!
Handle halogen light bulbs with care. The gas inside
a halogen light bulb is highly pressurized, so drop-
ping, knocking, or scratching a halogen light bulb
can cause it to shatter.
Never hold the halogen lights bulb with a bare hand,
dirty glove, etc.
The oil from your hand could cause the bulb to
break the next time the fog lights are used.
If the glass surface is dirty, clean it with alcohol and
let it dry completely before installing the bulb.
BK0151000US.book 76 ページ ２０１２年３月２９日　木曜日　午後６時８分

Vehicle care and maintenance
7-77
7
Front fog lights (Type 2)
(if so equipped)
N00943600747
1. Remove the screw (A).2. Pull the cover out in the direction of the arrow shown in
the illustration.
BK0151000US.book 77 ページ ２０１２年３月２９日　木曜日　午後６時８分

7-78 Vehicle care and maintenance
7
3. Remove the screws (B) and pull the entire light unit out.
NOTE
When unfastening the screws, be careful not to mistakenly
move the beam position adjustment screw (C).
Passenger’s side Driver’s sideBK0151000US.book 78 ページ ２０１２年３月２９日　木曜日　午後６時８分

Vehicle care and maintenance
7-79
7
4. Push the connector (D) to disconnect and remove the fog
light. 5. Remove the bulb assembly (E) by turning it counterclock-
wise.
6. To install the bulb, perform the removal steps in reverse.
BK0151000US.book 79 ページ ２０１２年３月２９日　木曜日　午後６時８分