transmission MITSUBISHI MONTERO 1998 Manual PDF
Page 765 of 1501
system.
3) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Using hand-held pressure/vacuum pump, apply\
0.42 psi. If scan tool reading reaches 0.42 psi, go to next step. If
reading does not reach 0.42 psi, go to step 8).
4) Disconnect EVAP canister purge hose. Connect Purge Flow
Indicator (MB995061) between EVAP canister and disconnected hose. Turn\
engine on and allow it to reach operating temperature. Turn all lights
and accessories off. Place transmission in Park or Neutral. Observe
purge flow indicator while increasing engine RPM several times. If
purge flow indicator reads less than 2.5 SCFH (20 cm(3)/sec), check
EVAP canister purge hose and EVAP canister port for clogging. If hose
and port are okay, check EVAP purge solenoid. See DTC P0443. If
solenoid is okay, replace EVAP canister. Go to step 20).
5) Using scan tool, read Engine Coolant Temperature (ECT)
sensor temperature (item 21). Compare scan tool reading with
temperature gauge reading. If readings are about the same, go to next
step. If readings are not about the same, go to DTC P0115 test.
6) Using a thermometer, check engine compartment ambient
temperature. Using scan tool, read Intake Air Temperature (IAT) sensor\
temperature (item 13). Compare IAT sensor and thermometer readings. If\
readings are not about the same, go to DTC P0110 test. If readings are
about the same, go to next step.
7) Using scan tool, read Power Steering Pressure (PSP) switc\
h
status (item 27). Switch status should read ON when steering wheel is
turned. If switch status is as specified, go to step 20). If switch
status is not as specified, go to DTC P0551 test.
8) Remove fuel cap. Install a fuel tank filler tube adapter
in place of fuel cap. Plug fuel filler tube adapter hose. Disconnect
and plug air filter-to-EVAP vent solenoid hose at air filter.
Disconnect intake manifold plenum-to-EVAP purge solenoid at intake
manifold plenum. Install a "T" fitting between vacuum hose and intake
manifold plenum. Connect hand-held pressure/vacuum pump to "T"
fitting. Go to next step.
CAUTION: DO NOT apply more than 0.57 psi in following step. Applying
more than specified psi can crack fuel tank.
NOTE: Ensure fuel tank is at least 1/4 full. The lower the fuel
level in fuel tank, the longer it takes to pressurize fuel
system.
9) Using scan tool, read Fuel Tank Differential Pressure
(FTDP) sensor (item 73). Using hand-held pressure/vacuum pump, apply\
0.42 psi. If scan tool reading reaches 0.42 psi, replace fuel cap. Go
to step 20). If reading does not reach 0.42 psi, go to next step.
10) Disconnect hand-held pressure/vacuum pump from "T"
fitting. Install an evaporative emission system tester in place of
vacuum held pump and apply 0.49 psi. Wait two minutes. If pressure
drops less than 0.20 psi, go to next step. If pressure drops 0.29 psi
or more, go to step 13).
11) Disconnect EVAP purge solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP purge
solenoid for leak. If EVAP purge solenoid is okay, replace hose. Go to
step 24). If pressure is maintained, go to next step.
12) Disconnect EVAP vent solenoid-to-EVAP canister hose at
EVAP canister. Connect hand-held pressure/vacuum pump to hose and
apply 0.9 psi. If pressure is not maintained, check EVAP vent solenoid
for leak. If EVAP vent solenoid is okay, replace hose. Go to step 20).
If pressure is maintained, replace EVAP canister. Go to step 24).
13) Ensure hoses are properly routed and connected. See M -
Page 767 of 1501
Fig. 40: Identifying VSS Test Terminals (Montero)
Courtesy of Mitsubishi Motor Sales of America
3) VSS is located at end of speedometer cable at
transmission. Connect battery, resistor (3-10 ohms) and voltmeter to
indicated terminals. See Fig. 41. Ensure voltage pulses 4 times per
speedometer shaft revolution. If voltage is not as specified, replace
VSS. If voltage is as specified, go to step 5).
Fig. 41: Testing VSS
Courtesy of Mitsubishi Motor Sales of America
4) With an assistant, road test vehicle. Drive vehicle at 25
Page 773 of 1501
should be actuated when pressure is 218-290 psi. Gradually open
shutoff valve to decrease pressure. Check pressure when PSP switch is
de-actuated. PSP switch should de-actuate at 102-174 psi. Turn engine
off. If PSP operates as specified, go to next step. If PSP does not
operate as specified, replace PSP switch. Go to step 8).
5) Disconnect PSP switch connector. On 3000GT, go to next
step. On Montero, turn ignition off. Disconnect PCM connector. Ground
PCM connector terminal No. 54. Using DVOM, check continuity between
chassis ground and PSP switch connector terminal No. 1. If continuity
does not exist, repair wiring harness as necessary. If continuity
exists, go to next step.
6) Turn ignition on. Using DVOM, check voltage between ground
and PSP switch connector terminal No. 1. If battery voltage does not
exist, replace PCM. If battery voltage exists, go to next step.
7) Road test vehicle and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
test is complete.
DTC P0705: TRANSMISSION RANGE SENSOR CIRCUIT FAILURE
DTC P0705 is related to automatic transmission diagnostics.
For diagnostic procedure, see TRANSMISSION SERVICE & REPAIR article.
DTC P1103 & P1104: TURBOCHARGER WASTEGATE SOLENOID CIRCUIT
FAILURE
NOTE: This test applies to 3000GT with turbocharger only. For
terminal identification, see TERMINAL IDENTIFICATION. For
circuit and wire color identification, see
L - WIRING DIAGRAMS article.
1) If using scan tool, go to step 7). Remove vacuum hoses
from turbocharger wastegate solenoid. Disconnect solenoid harness
connector. Connect a vacuum pump to solenoid nipple "A". See Fig. 46.
Go to next step.
2) Using jumper wires, connect battery voltage and ground to
solenoid terminals. Ensure vacuum does not hold with nipple "B"
unplugged, and negative jumper wire connected. If solenoid does not
test as specified, replace solenoid. If solenoid tests as specified,
go to next step.
Fig. 46: Testing Turbocharger Wastegate Solenoid
Courtesy of Mitsubishi Motor Sales of America
3) Ensure solenoid holds vacuum with nipple "B" plugged, and
negative jumper wire connected. If solenoid does not test as
Page 776 of 1501
wiring harness as necessary. If continuity exists, go to next step.
5) Reconnect PCM connector. Turn ignition switch to ON
position. Check voltage between chassis ground and MDP sensor
connector terminal No. 3. If voltage is not 4.8-5.2 volts, replace
PCM. If voltage is as specified, condition required to set DTC is not
present at this time. Go to next step.
6) Test is complete. Intermittent problem may exist. Road
test vehicle (if necessary) and attempt to duplicate conditions that
caused original complaint. Recheck for DTCs. If no DTCs are displayed,
go to INTERMITTENT DTCS .
DTC P1600: SERIAL COMMUNICATION LINK MALFUNCTION
DTC P1600 is related to automatic transmission diagnostics.
For diagnostic procedure, see TRANSMISSION SERVICE & REPAIR article.
DTC P1715: PULSE GENERATOR FAILURE
DTC P1715 is related to automatic transmission diagnostics.
For diagnostic procedure, see TRANSMISSION SERVICE & REPAIR article.
DTC P1750: SOLENOID FAILURE
DTC P1750 is related to automatic transmission diagnostics.
For diagnostic procedure, see TRANSMISSION SERVICE & REPAIR article.
DTC P1791: ENGINE COOLANT TEMPERATURE LEVEL INPUT TO TCM
DTC P1791 is related to automatic transmission diagnostics.
For diagnostic procedure, see TRANSMISSION SERVICE & REPAIR article.
SUMMARY
If no hard DTCs (or only pass DTCs) are present, driveability\
symptoms exist, or intermittent DTCs exist, proceed to H - TESTS W/O
CODES article for diagnosis by symptom (i.e., ROUGH IDLE, NO START,
etc.) or intermittent diagnostic procedures.
Page 816 of 1501
Torque Converter Clutch Solenoid/Switch ......... Engine Performance
Traction Control Switch ........................... Anti-Lock Brakes
Trailer Tow Connector .............................. Exterior Lights
Trailer Tow Relay .................................. Exterior Lights
Transmission/Transaxle .......................... Engine Performance
Transmission Control Module (TCM) ............... Engine Performance\
Starters
Transmission Range Sensor ................................. Starters
Back-Up Lights
Engine Performance
Transmission Range Switch ........................... Back-Up Lights
Engine Performance
Anti-Theft System
Turn Signal Flasher ................................ Exterior Lights
Turn Signal Lights ................................. Exterior Lights
Twilight Sentinel Switch ......................... Headlight Systems
Daytime Running Lights
Vapor Canister Leak Detection Pump .............. Engine Performance
Vehicle Control Module (VCM) .................... Engine Performance\
Vehicle Dynamic Module ....................... Electronic Suspension
Vehicle Speed Control Servo ................. Cruise Control Systems
Vehicle Speed Sensor .......................... Data Link Connectors
Analog Instrument Panels
Cruise Control Systems
Electronic Suspension
Voltage Regulator .......................... Generators & Regulators
Water-In-Fuel Sensor ............................ Engine Performance
Analog Instrument Panels
Wheel Speed Sensors ............................... Anti-Lock Brakes
Window Timer Module .......................... Power Convertible Top
Windshield Intermittent Wiper Relay ........... Wiper/Washer Systems
Windshield Washer Motor ....................... Wiper/Washer Systems
Wiper Motor ................................... Wiper/Washer Systems
\
\
\
\
\
\
\
Page 819 of 1501
Fig. 3: Identifying PCM Terminals (Eclipse 2.0L Turbo, 2.4L & Mirage)\
Courtesy of Mitsubishi Motor Sales of America
Fig. 4: Identifying PCM Terminals (Galant)
Courtesy of Mitsubishi Motor Sales of America
Fig. 5: Identifying PCM Terminals (All Other Models)
Courtesy of Mitsubishi Motor Sales of America
ENGINE SENSORS & SWITCHES
NOTE: For circuit identification, see appropriate wiring diagram
in L - WIRING DIAGRAMS article.
Automatic Transaxle/Transmission Range Switch Or Park Neutral
Position Switch
See G - TESTS W/CODES article.
Barometric Pressure Sensor
Sensor is a part of volume airflow sensor assembly. See G -
TESTS W/CODES article.
Closed Throttle Position Switch
Switch is part of throttle position sensor. See CLOSED
Page 823 of 1501
INSTRUMENT PANEL
1998 Mitsubishi Montero
1998 ACCESSORIES & EQUIPMENT
Mitsubishi - Instrument Panels
Eclipse, Galant, Mirage, Montero, Montero Sport, 3000GT
DESCRIPTION & OPERATION
WARNING: Deactivate air bag system before performing any service
operation. See AIR BAG RESTRAINT SYSTEMS article. Do not
apply electrical power to any component on steering column
without first deactivating air bag system. Air bag may
deploy.
Instrument cluster includes speedometer, fuel gauge and
temperature gauge. Fuel gauge has a built-in voltage limiter to keep
voltage supply to gauges at 7 volts. Some models may also have an
ammeter, oil pressure gauge, tachometer, voltmeter and/or turbo boost
pressure gauge. Oil pressure gauge uses full battery voltage.
Tachometer operates by pulse feed.
COMPONENT LOCATIONS
COMPONENT LOCATIONS TABLE \
\
\
\
\
\
Component Location
Engine Coolant Temperature (ECT) Sensor
Eclipse, Galant, Montero
& Montero Sport ................. On Thermostat Housing
Mirage ........................ On Rear Of Cylinder Head
3000GT ........... On Cylinder Head, Below Ignition Coil
Input Speed Sensor
Eclipse ........................... On Side Of Transaxle
Output Speed Sensor
Eclipse ........................... On Side Of Transaxle
Vehicle Speed Sensor
Eclipse, Galant,
Mirage & 3000GT ................... On Top Of Transaxle
Montero & Montero Sport ...... On Transmission Tailshaft
\
\
\
\
\
\
TROUBLE SHOOTING
FUEL/TEMPERATURE GAUGE NOT WORKING
Check for blown fuse, faulty voltage limiter and faulty
relay. Ensure sending unit connections are clean and tight. Test
sending unit for correct operation. Tighten connections in instrument
cluster.
SPEEDOMETER NOT WORKING
On mechanical-type speedometers, ensure speedometer cable is
properly connected and correctly routed. If speedometer pointer and/or
odometer still do not work, replace speedometer cable or speedometer
assembly.
On electric-type speedometers, check for faulty vehicle speed
sensor, input/output sensors or faulty circuit. For testing, see
Page 874 of 1501
J - PIN VOLTAGE CHARTS
1998 Mitsubishi Montero
1998 ENGINE PERFORMANCE
Mitsubishi - Pin Voltage Charts
Diamante, Eclipse, Galant, Mirage, Montero, Montero Sport,
3000GT
INTRODUCTION
NOTE: Unless stated otherwise in testing procedures, perform all
voltage tests using a Digital Volt-Ohmmeter (DVOM) with a
minimum 10-megohm input impedance. Voltage readings may vary
slightly due to battery condition or charging rate.
Pin voltage charts are supplied to reduce diagnostic time.
Checking pin voltages at the PCM connector determines whether it is
receiving and transmitting proper voltage signals. Diagnostic charts
may also help determine if PCM harness is shorted or open.
TEST PROCEDURE
CAUTION: Shorting positive DVOM lead between connector terminal and
ground could damage vehicle wiring, sensor and PCM.
1) If necessary, remove Powertrain Control Module (PCM) to
access harness connector. For PCM location, see PCM LOCATION table.
Leave PCM connectors connected.
2) Using DVOM, backprobe terminals. Connect positive DVOM
lead to appropriate PCM terminal. Connect negative DVOM lead to PCM
ground terminal. For PCM terminal identification, see appropriate
chart. See Figs. 1-24.
3) All measurements are applicable to vehicle at normal
operating temperature at sea level. Unless otherwise noted, engine is
idling when specification requires engine running. Ensure transmission
shift selector is in Neutral or Park (as applicable). If DVOM displays\
measurement that is not within specification, see G - TESTS W/CODES
article.
PCM LOCATION TABLE
\
\
\
\
\
\
Application Location
Eclipse 2.0L Non-Turbo ............ In Front of Left Front
Strut Tower
Mirage & Montero Sport .............. Behind Right Side Of
Instrument Panel (Glove Box)
Montero ........................... Right Front Kick Panel
All Others ......................... Behind Center Console
\
\
\
\
\
\
Fig. 1: Identifying PCM Terminals (Diamante)
Courtesy of Mitsubishi Motor Sales of America
Page 964 of 1501
\
\
\
\
\
\
\
\f
Engine Oil Ambient Temperature Less Than SAE 5W-30
(
1) 0\bF (-18\bC) To 100\bF (38\bC)
\
\
\
\
\
\
\f
Ambient Temperature Above 0\bF SAE 10W-30
(-18\bC) To Over 100\bF (38\bC)
\
\
\
\
\
\
\
\f
Power All Automatic Transmission
Steering Fluid DEXRON II
Fluid
\
\
\
\
\
\
\
\f
Engine All 50/50 Mixture Of
Coolant Distilled Water &
Ethylene Glycol
\
\
\
\
\
\
\
\f
Transfer Case All API Classification GL-4
SAE 75W-85W Or 75W-90
\
\
\
\
\
\
\
\f
Front Axle All API Classification GL-5
Or Higher (
2)
\
\
\
\
\
\
\
\f
Clutch Fluid All DOT 3 Or DOT 4
\
\
\
\
\
\
\
\f
Hook Lock All Multipurpose Grease
Catch, Door NLGI Grade 2
Lock Strikers
Seat Adjust-
ers, Backdoor
Lock, Parking
Brake Cable
Mechanism
\
\
\
\
\
\
\
\f
Front Wheel All Multipurpose Grease
Bearings NLGI Grade 2 Or
Equivalent
\
\
\
\
\
\
\
\f
Door Hinges, All Engine Oil
Back Door
Hinges
\
\
\
\
\
\
\
\f
A/C All HFC-134a
Refrigerant
\
\
\
\
\
\
\
\f
Manual All API Classification GL-4
Transmission SAE 75W-85W Or 75W-90
\
\
\
\
\
\
\
\f
Automatic All "ATF DEXRON II" Or
Transmission Equivalent
\
\
\
\
\
\
\
\f
Brake Fluid All DOT 3 Or DOT 4
\
\
\
\
\
\
\
\f
Rear Axle All API Classification GL-5
Or Higher (
2)
\
\
\
\
\
\
\
\f
(
1) - SAE 5W-30 engine oil is preferred. SAE 10W-30 may be used if
the Ambient Temperature is above 0\b F (-18\b C).
(
2) - SAE90, 85W-90, 80W-90 may be used in temperatures above
-10\b F (-23\b C). SAE 80W, 80W-90 may be used in temperatures
from -30\b F (-34\b C) to -10\b F (-23\b C). SAE 75W may be used
in temperatures below -30\b F (-34\b C).
\
\
\
\
\
\
\
Page 965 of 1501
FLUID CAPACITIES
FLUID CAPACITIES TABLE ( 1) \
\
\
\
\
\
\
Item Condition Specification
\
\
\
\
\
\
\
\f
Engine Oil Oil Pan 4.5 Qts. (4.3L)
(
1)
\
\
\
\
\
\
\f
Oil Filter 0.32 Qts. (0.3L)
\
\
\
\
\
\
\f
Oil Cooler 0.32 Qts. (0.3L)
\
\
\
\
\
\
\
\f
Power Drained 1.1 Qts. (1.0L)
Steering
\
\
\
\
\
\
\
\f
Automatic Drained 8.9 Qts. (8.5L)
Transmission
\
\
\
\
\
\
\
\f
Manual Drained 3.3 Qts. (3.2L)
Transmission
\
\
\
\
\
\
\
\f
Transfer Case Drained 2.6 Qts. (2.5L)
\
\
\
\
\
\
\
\f
Front Axle Drained 1.3 Qts. (1.2L)
\
\
\
\
\
\
\
\f
Rear Axle Drained 3.3 Qts. (3.2L)
\
\
\
\
\
\
\
\f
A/C Drained 27 oz (760 g)
Refrigerant
\
\
\
\
\
\
\
\f
Fuel Tank Capacity 24 gal (92L)
\
\
\
\
\
\
\
\f
(
1) - Capacities are recommended or calculated levels. Always use
dipstick to measure level.
\
\
\
\
\
\
\
WHEEL & TIRE SPECIFICATIONS
Tire specifications are imprinted on the tire side wall. The
recommended cold tire inflation pressures are listed on a label
attached to the rear face of the driver's door. These pressures
provide the best combination of ride comfort, tire wear and stability
under normal conditions.
CAUTION: DO NOT mix tires of different design such as radial ply
with bias or bias-belted tires. Mixing tire types will
adversely affect road handling and may lead to loss of
vehicle control. When using snow tires, they must be used
in set of four for maneuverability and safety. DO NOT use
tire chains on front wheels.
TIRE & WHEEL SPECIFICATIONS TABLE
\
\
\
\
\
\
Wheel Size Tire Size
15 x 6JJ (Steel or Aluminum) .................. P235/75R15
15 X 7JJ (Aluminum) ........................... P265/70R15
\
\
\
\
\
\
WHEEL TIGHTENING