open tailgate MITSUBISHI OUTLANDER 2010 2.G Owners Manual

Seat and restraint systems
2-17
2
To fold out the third seat1. Open the tailgate. Refer to “Flap-fold tailgate” on page 3-
60.
2. From the rear of the vehicle, pull up the cover.
Secure the cover to the seatback with the strap (A).3. Pull on the strap (B) on the center of the seatback to raise
the seatback upright.
BK0115300US.book 17 ページ ２００９年７月１６日　木曜日　午前９時１３分

Seat and restraint systems
2-21
2
To stow the third row seatNOTE

Before stowing the third row seat, make sure that there is
no luggage in the storage area. Storing the seat with lug-
gage in the storage area could damage the seat.
1. Open the tailgate. Refer to “Flap-fold tailgate” on page 3-
60.
2. From the rear of the vehicle, pull up the cover (A).
Secure the cover to the seatback with the strap (B).3. For each head restraint, while tilting the head restraint
backward, slide the knob (C) and fold the head restraint
forward.
BK0115300US.book 21 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-4 Features and controls
3
NOTE

The key is a precision electronic device with a built-in sig-
nal transmitter. Please observe the following in order to
prevent damage.
 Do not leave where it may be exposed to heat caused by
direct sunlight, such as on top of the dashboard.
 Do not take the remote control transmitter apart.
 Do not excessively bend the key or subject it to strong
impacts.
 Keep the remote control transmitter dry.
 Keep away from magnetic objects such as key rings.
 Keep away from devices that produce magnetism, such
as audio systems, computers and televisions.
 Keep away from devices that emit strong electromag-
netic waves, such as cellular phones and wireless
devices.
 Do not clean with ultrasonic cleaners.
 Do not leave the key where it may be exposed to high
temperature or high humidity.


If you lose your key, to prevent the theft of the vehicle
immediately contact an authorized Mitsubishi Motors
dealer.
If you notify an authorized Mitsubishi Motors dealer of
the key number, they can make a new key. The key num-
ber is stamped on the key number plate. Keep the key
number plate in a safe place separate from the key itself.


No keys other than those registered in advance can be
used to start the engine.
Refer to “Electronic immobilizer (Anti-theft starting sys-
tem)” on page 3-5.
Refer to “Free-hand Advanced Security Transmitter
(F.A.S.T.-key): “Electronic immobilizer (Anti-theft start-
ing system)” on page 3-24.


Be careful of the following if the theft-alarm is set to
“Activate”.
Refer to “Theft-alarm system” on page 3-66.
 When the theft-alarm is in the system operational status,
the alarm operates if a door or tailgate is opened after
using the key, the door lock knob or the power door lock
switch to unlock the vehicle.
 Even if the theft-alarm is set to “Activate”, the system
does not enter the preparation status if the keyless entry
system or the F.A.S.T.-key was not used to lock the
vehicle.
BK0115300US.book 4 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-10 Features and controls
3
To l o c kPress the LOCK button (1) to lock all the doors and the tail-
gate.
The turn signal lights will also blink once.NOTE

If you press the LOCK button (1) twice the horn will
sound once.
To unlockPress the UNLOCK button (2) to unlock the driver’s door only.
Within about 2 seconds, press the UNLOCK button one more
time to unlock all the doors and tailgate.
The dome light will turn on for 30 seconds. The turn signal
lights will also blink twice.
For vehicles equipped with the color multi-information display,
the front side-marker and parking lights will also turn on for
about 30 seconds. Refer to “Welcome light” on page 3-219.NOTE

On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to the separate operation manual.


The door and tailgate unlock function can be set so that all
doors and tailgate unlock when the UNLOCK button (2)
is pressed once.
Refer to “Setting of door and tailgate unlock function” on
page 3-11.
Answerback functionThe horn and turn signal lights of the keyless entry system
answerback function can be changed as required. This is done
with the key removed from the ignition switch.NOTE

The answerback function will not operate if any of the
doors are open.
BK0115300US.book 10 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-11
3
Horn deactivation/reactivationThe answerback function can be set in the following three
ways.
Each time the answerback function is set, a chime will sound to
tell you the condition of the answerback function.
1. Remove the key from the ignition switch.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the UNLOCK and LOCK buttons
within 10 seconds of pressing the UNLOCK button in step
3.NOTE

On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to the separate operation manual.
Turn signal lights deactivation/reactivationThe answerback function can be turned ON or OFF separately.
1. Remove the key from the ignition switch.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the UNLOCK button (2) for 4 to 10 seconds and
press the LOCK button (1) during this time.4. Release in sequence the UNLOCK and LOCK buttons
within 10 seconds of pressing the LOCK button in step 3.
NOTE

On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to the separate operation manual.
Setting of door and tailgate unlock function
N00543600062
The door and tailgate unlock function can be set to the follow-
ing two conditions.
Each time the door and tailgate unlock function is set, a chime
will sound to tell you the condition of the door and tailgate
unlock function.
One chime: The horn will not sound.
Two chimes: The horn will sound.
Four chimes: The horn will sound if the LOCK button is
pressed twice within 1 second.
Number of chimes
To l o c k
To u n l o c k
One chime One flash Two flashes
Two chimes One flash No flash
Three chimes No flash Two flashes
Four chimes Two flashes One flash
Five chimes No flash One flash
Six chimes Two flashes No flash
Seven chimes No flash No flashNumber of
chimes
Condition
One chime All doors and the tailgate unlock
Two chimes Driver’s door unlock only
BK0115300US.book 11 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-12 Features and controls
3
1. Remove the key from the ignition switch.
2. Open the driver’s door and turn the combination head-
lights and dimmer switch to the “OFF” position.
3. Press the LOCK button (1) for 4 to 10 seconds and press
the UNLOCK button (2) during this time.
4. Release in sequence the LOCK and UNLOCK buttons
within 10 seconds of pressing the LOCK button in step 3.NOTE

On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to the separate operation manual.
Using the panic alarm
N00543700034
If you are near your vehicle and feel threatened, you may acti-
vate the alarm to call attention as follows:
1. Press the PANIC button (3) for more than 1 second.
2. The headlights will blink on and off and the horn will
sound intermittently for about 3 minutes.
3. To turn off the alarm, press any button on the remote con-
trol transmitter.
Replacement remote control transmitters
N00543800048
Only remote control transmitters programmed with the vehi-
cle’s electronics can lock or unlock all doors and the tailgate.
If you lose the remote control transmitter, you can order a
remote control transmitter from your authorized Mitsubishi
Motors dealer by referring to the key number.
To prevent vehicle theft, the ID code for the remote control
transmitter must be changed.
Take your vehicle and all remote control transmitters to your
authorized Mitsubishi Motors dealer to have your ID code
changed.Additional remote control transmitters
N00543900049
To add a remote control transmitter, you must already have 1
registered remote control transmitter.
Registering the ID code can be done by yourself or by your
authorized Mitsubishi Motors dealer. For you to register the ID
code yourself, follow the “Customer remote control transmitter
programming” procedure below.
If you choose to have your authorized Mitsubishi Motors
dealer register the ID code, take your vehicle and any remain-
ing keys to your authorized Mitsubishi Motors dealer.NOTE

You are provided with 2 remote control transmitters, but
you may register up to 8 remote control transmitters.
BK0115300US.book 12 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-13
3
Customer remote control transmitter program-
ming
N00544000063
You can program new remote control transmitters to the system
if you have one valid (already registered) remote control trans-
mitter by doing the following:
1. Have available all (current and new) remote control trans-
mitters you wish to register.
2. With a valid (already registered) remote control transmit-
ter, press the UNLOCK button (2) for 4 to 10 seconds.
Then press and hold the LOCK button (1).
3. Within 10 seconds of pressing the LOCK button, release
the LOCK and UNLOCK buttons in sequence.
At this time, ID codes for all remote control transmitters
except for the transmitter used in steps 2 and 3 are erased
and the answerback function (door is locked and
unlocked) informs you that the registration mode has been
activated.
4. Within 60 seconds after step 3, complete the following ID
code registration operation using the next remote control
transmitter you wish to register within 4 seconds.
i) Press both the LOCK and UNLOCK buttons for 2 sec-
onds.
ii) Release both the LOCK and UNLOCK buttons for 1
second.
iii) Press the UNLOCK button. The answerback function
informs you that the ID code registration of the transmitter
is completed.
5. To register the ID codes of additional remote control
transmitters, repeat step 4 within 60 seconds after step 4.6. If no ID code of a remote control transmitter is registered
within 60 seconds after step 4, the registration mode is
canceled and the normal mode returns.
NOTE

For verification purposes, try to lock and unlock the doors
after the registration is completed.


The indicator light (4) comes on each time a button is
pressed.


The keyless entry system does not work if the key is in the
ignition switch.


The remote control transmitter can be used from about 40
feet (12 m) away. However, this distance may change if
your vehicle is near a TV transmitting tower, a power sta-
tion, or a radio station.


If the UNLOCK button (2) is pressed when all doors and
the tailgate are locked and no doors or the tailgate are
opened within about 30 seconds, the doors and the tailgate
will automatically re-lock.
On a vehicle equipped with a Mitsubishi Multi-Communi-
cation System, the functions can be adjusted on the
screen. For details, refer to the separate operation manual.


If the following conditions are observed after pressing the
LOCK (1) or UNLOCK (2) button on the remote control
transmitter, the battery in the remote control transmitter
may need to be replaced.
 The doors and the tailgate cannot be locked or unlocked.
 The panic alarm cannot be operated.
 The indicator light (4) is dim or does not come on.


If you lose your remote control transmitter, please contact
an authorized Mitsubishi Motors dealer for a replacement.
BK0115300US.book 13 ページ ２００９年７月１６日　木曜日　午前９時１３分

3-16 Features and controls
3Free-hand Advanced Security Transmitter
(F.A.S.T.-key)
(if so equipped)
N00503100094
The Free-hand Advanced Security Transmitter (F.A.S.T.-key)
enables the doors and the tailgate to be locked and unlocked
and the engine to be started simply by carrying it.
The F.A.S.T.-key can also be used as the remote control trans-
mitter of the keyless entry system.
Refer to “Free-hand Advanced Security Transmitter (F.A.S.T.-
key): Keyless entry system” on page 3-47.
CAUTION
!

When the remote control transmitter case is opened,
be careful to keep water, dust, etc. out. Also, do not
touch the internal components.
The F.A.S.T.-key must be carried by the driver. The F.A.S.T.-
key is required for vehicle operations such as locking and
unlocking the doors and the tailgate, and starting the engine.
When leaving the vehicle, make sure you are carrying the
F.A.S.T.-key and then lock the vehicle.
WA R N I N G
!

Individuals who use implantable pacemakers or
implantable cardiovascular-defibrillators should
keep away from the external and internal transmit-
ters. The electromagnetic waves used in the F.A.S.T.-
key may affect the operation of implantable pace-
makers and implantable cardiovascular-defibrilla-
tors.
BK0115300US.book 16 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-21
3
NOTE

In cases such as the following, the F.A.S.T.-key does not
operate.
 There is a F.A.S.T.-key in the passenger compartment
 A door or the tailgate is open or ajar
 The ignition switch is in a position other than “LOCK”
 The emergency key is inserted into the ignition switch


When the vehicle is locked, the theft alarm system pre-
pares to enter the armed stage.
Refer to “Theft-alarm system” for further details on page
3-66.


Pull the handle of a door or the tailgate within about 3 sec-
onds of locking to confirm that the vehicle is locked.


If the handle is operated 3 seconds or more after the vehi-
cle is locked, the doors and the tailgate are unlocked
again.


The time within which locking confirmation is possible
can be adjusted. See an authorized Mitsubishi Motors
dealer for details.
Tailgate switch
BK0115300US.book 21 ページ ２００９年７月１６日　木曜日　午前９時１３分

Features and controls
3-23
3
Hold the handle of the front passenger door or pull the handle
of the tailgate to unlock all the doors and the tailgate.NOTE

If the doors are unlocked when all doors and the tailgate
are locked and no doors or the tailgate are opened within
about 30 seconds, the doors and the tailgate will automati-
cally re-lock.


The doors and the tailgate cannot be unlocked for about 3
seconds after locking.


In cases such as the following, the F.A.S.T.-key does not
operate.
 A door or the tailgate is open or ajar
 The ignition switch is in a position other than “LOCK”
 The emergency key is inserted into the ignition switch


The time within which locking confirmation is possible
can be adjusted. See an authorized Mitsubishi Motors
dealer for details.


To unlock the vehicle, firmly hold the sensor (B) on the
rear of the door handle (A), and after confirming that the
vehicle is unlocked, pull the handle. However, in cases
such as the following, the vehicle may not unlock or
unlocking may be delayed.
 You are not touching the sensor on the rear of the handle
 Leather gloves or ski gloves are worn when touching the
sensor on the rear of the handle
 You are also carrying a F.A.S.T.-key of a different vehi-
cle, or a communication device or electric appliance that
emits electromagnetic waves is carried at the same time


The vehicle may not be unlocked if the door handle is
operated too quickly. If this happens, hold the handle
again and after confirming that the vehicle is unlocked,
pull the handle.
Front passenger door handle Tailgate handle
BK0115300US.book 23 ページ ２００９年７月１６日　木曜日　午前９時１３分