change time MITSUBISHI OUTLANDER 2020 Owner's Manual (in English)

N09200102404
Thank you for buying a MITSUBISHI OUTLANDER. We are confident you will enjoy your
vehicle. It has
been engineered
for optimum performance, durability and comfort. By thoroughlyreading this Owner’s Manual, you w
ill gain an understanding of the
many features that are included in the OUTLANDER. The Owner’s Manual contains descripti
ons and illustrations that will assist in the
operation and maintenance of your vehicle. Your Authorized Mitsubishi Motors
Dealer will be
happy to assist you
with any further questions you ma
y have regarding the operation of
your vehicle.Please note that this manual appl
ies to all OUTLANDER models and
explains all features in
cluding options. Some feat
ures explained in this
manual may not be inst
alled on your vehicle.
Please leave this Owner’s Manual in the vehicle at the time of resale. The next owner will appreciate ha
ving access to the information con-
tained here. This manual includes instructions fo
r standard and optional equipment
available at the time of printing. Mitsubishi Motors Corporationreserves the right to make changes
in design and specifications and to
make additions or improvements in
its product without assuming any
obligation to install these on pr
eviously manufac
tured products.
Introduction
Throughout this manual the words
WARNING
and
CAUTION
appear.These are reminders to be especially careful. Failure to follow the instructions could result in persona
l injury or damage to your vehi-
cle. Indicates a strong possibility of se
vere personal injury or death if
instructions are not followed. Points out hazards or unsafe pr
actices that could cause minor
personal injury
or damage to your vehicle.
You will see another important symbol: NOTE Gives helpful information. As with other vehicles of
this type, failure to
operate this vehicle cor-
rectly may result in loss of contro
l or an accident. Be sure to read
“on-pavement” and “off-road” driv
ing guidelines in the “Driving
safety” and “Features an
d controls” sections.
©2019 Mitsubishi Motors Corp
oration Printed in Japan
BK0278200US.book 1 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped)
Features and controls 5-7
5
Operation is subject to the following two con- ditions.  This device may not
cause harmful inter-
ference.  This device must ac
cept any interference
received, including interference that maycause undesired operation.
N00509002161
Press the remote control transmitter buttons to lock or unlock the doors and the liftgate. It can also help you signal for attention bysetting off the panic alarm.
Press the LOCK button (1) to lock all the doors and the liftgate.The turn signal lights
will also blink once.
Press the UNLOCK button (2) to unlock the driver’s door only. Within approximately 2 seconds, press theUNLOCK button one more time to unlock all the doors and liftgate. The dome light will turn on for 30 seconds.The turn signal lights will also blink twice.
CAUTION Changes or modifica
tions not expressly
approved by the manufacturer for compli-ance could void the user’s authority to oper- ate the equipment.
Keyless entry system
(if so
equipped)1-
LOCK ( ) button
2-
UNLOCK ( ) button
3- PANIC button 4- Indicator light
NOTE
 On vehicles equipped wi
th the mirror retrac-
tor switch, the outside rearview mirrors auto-matically retract or extend when the doorsand the liftgate are locked or unlocked using the remote control swit
ches of the keyless
entry system.Refer to “Features and controls: Outside rearview mirrors” on page 5-63.
To l o c k

NOTE
 If you press the LOCK button (1) twice the horn will sound once.
To unlock

BK0278200US.book 7 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped) 5-8 Features and controls
5
The front side-marker and parking lights will also turn on for approximately 30 seconds.Refer to “Welcome light” on page 5-207.
N00543501130
The horn and turn signal lights of the keyless entry system answerback function can be changed as required. This is done with thekey removed from the ignition switch.
N00597000043
The answerback function can be set in thefollowing three ways.Each time the answerback function is set, a chime will sound to tell you the condition of the answerback function. To change the settings, refer to “Customizing the keyless entry system” on page 5-12.
N00597100044
The answerback function can be turned ONor OFF separately. Each time the answerback function is set, a chime will sound to
tell you the condition of
the answerback function. To change the settings, refer to “Customizing the keyless entry system” on page 5-12.
N00543601258
The door and liftgate
unlock function can be
set to the following two conditions.
NOTE
 If the UNLOCK button (2) is pressed and no doors or the liftgate are opened withinapproximately 30 seconds, the doors and the liftgate will automatically re-lock. On a vehicle equipped
with the Smartphone-
link Display Audio (SDA), the functions can be adjusted on the scre
en. For details, refer
to the separate owner’s manual.  The door and liftgate
unlock function can be
set so that all doors a
nd liftgate unlock when
the UNLOCK button (2) is pressed once. Refer to “Setting of door
and liftgate unlock
function” on page 5-8.
Answerback function

NOTE
 The answerback functi
on will not operate if
any of the doors are open.
 On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the functions can
be adjusted on the screen. For details, referto the separate owner’s manual.
Horn deactivation/reactivation

Number of chimes
Condition
One chime The horn will not sound. Two chimes The horn will sound. Four chimes
The horn will sound if the LOCK button is pressed twice within 1 second.
NOTE
Turn signal lights deactiva- tion/reactivation

Number of chimes
To l o c k
To u n l o c k
One chime One flash Two flashes Two chimes One flash No flash Three chimes No flash Two flashes Four chimes Two flashes One flash Five chimes No flash One flash Six chimes Two flashes No flash Seven chimes
No flash No flash
Setting the door and liftgate unlock function

BK0278200US.book 8 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped)
Features and controls 5-9
5
Each time the door and
liftgate unlock func-
tion is set, a chime will
sound to tell you the
condition of the door and liftgate unlock function. To change the settings, refer to “Customizing the keyless entry system” on page 5-12.
N00543701060
If you are near your vehicle and feel threat-ened, you may activate the alarm to call atten- tion as follows: 1. Press the PANIC button (3) for more than 1 second.
2. The headlights will blink on and off and the horn will sound intermittently forabout 3 minutes. 3. To turn off the alarm, press any button on the remote control transmitter.
N00543801087
Only remote control transmitters pro- grammed with the vehicle’s electronics can lock or unlock all doors and the liftgate. If you lose the remote control transmitter, you can order a remote c
ontrol transmitter from
your authorized Mitsubi
shi Motors dealer by
referring to the key number.To prevent vehicle theft, the ID code for the remote control transmitter must be changed. Take your vehicle and all remote controltransmitters to your authorized Mitsubishi Motors dealer to have your ID code changed.
N00543900049
To add a remote control transmitter, you must already have 1 registered remote controltransmitter. Registering the ID code can be done by your- self or by your authorized Mitsubishi Motors
dealer. For you to regist
er the ID code your-
self, follow the “Customer remote controltransmitter programming” procedure below. If you choose to have your authorized Mitsubishi Motors dealer register the IDcode, take your vehi
cle and any remaining
keys to your authorized Mitsubishi Motors dealer.
N00544001275
You can program new remote control trans- mitters to the system if you have one valid (already registered) remote control transmit-ter by doing the following: 1. Have available all (current and new) remote control transmitters you wish to register.
Number of chimes
Condition
One chime [Factory set- ting]
When the UNLOCK button (2) is pressed one time, all doors and the liftgate unlock.
Two chimes
When the UNLOCK button (2) is pressed one time, only the driver’s door unlocks. When the UNLOCK button is pressed two times in suc- cession, all doors and the lift- gate unlock.
Using the panic alarm

Replacement remote control transmitters

Additional remote control transmitters

NOTE
 You are provided with 2 remote control transmitters, but you may register up to 8 remote control transmitters.
Customer remote control trans- mitter programming (Except for vehicles sold in Canada)

BK0278200US.book 9 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Keyless entry system (if so equipped) 5-10 Features and controls
5
2. Using a valid (already registered) remote control transmitter, ac
tivate the registra-
tion mode according to the following steps. Steps ii to iv should be completed within 8 seconds.
3. Within 60 seconds after step 2, complete the following ID code
registration opera-
tion using the next remote control trans- mitter you wish to register within 4 seconds. 4. To register the ID
codes of additional
remote control transmitters, repeat step 3 within 60 seconds after step 3.5. If no ID code of a remote control trans- mitter is registered within 60 seconds after step 3, the regi
stration mode is can-
celed and the normal mode returns.
i) Press and hold the
UNLOCK button (2) for 4 to 8 seconds.
ii) While holding the
UNLOCK button (2), press the LOCK but-ton (1).
iii) While holding the
UNLOCK button (2), release the LOCK but- ton (1).
iv)
Release the UNLOCK button (2).NOTE
 ID codes for all remote control transmitters except for the transmitter used in steps 2 are erased and the answerback function (door is locked and unlocked) informs you that theregistration mode ha
s been activated.
i) Press both the LOCK
and UNLOCK but- tons for 2 seconds.
ii) Release both the
LOCK and UNLOCK buttons for 1 second.
iii)
Press the UNLOCK button.NOTE
 Be sure to press the buttons correctly when performing the procedures. If you perform the procedures incorrectly, the registered ID code information could
be deleted or the set-
tings could be changed
unintentionally. If the
registered ID code in
formation is deleted,
register the remote control transmittersagain.
 For verification purposes, try to lock and unlock the doors after the registration iscompleted.  The indicator light (4) comes on each time a button is pressed.  The keyless entry system does not work if the key is in the ignition switch.  The remote control transmitter can be used from approximately 40
feet (12 m) away.
However, this distance
may change if your
vehicle is near a TV
transmitting tower, a
power station, or
a radio station.
 If the following conditi
ons are observed after
pressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, the battery in the remote control transmitter may need to be replaced. • The doors and the lift
gate cannot be locked
or unlocked. • The panic alarm
cannot be operated.
• The indicator light
(4) is dim or does not
come on.
 If you lose your remote control transmitter, please contact an au
thorized Mitsubishi
Motors dealer for a replacement.  If you wish to obtain
an additional remote
control transmitter, please contact an autho-rized Mitsubishi Moto
rs dealer. A maximum
of 8 remote control tr
ansmitters can be pro-
grammed for your vehicle.NOTE
BK0278200US.book 10 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-18 Features and controls
5
While carrying the F.A.S.T.-key within the operating range, you can unlock the doorsand the liftgate by using the F.A.S.T.-key operation. The dome light will turn on for 30 seconds.The turn signal lights will blink twice and the buzzer will
sound twice.
Also refer to “Door locks”, “Power door locks”, “Liftgate” and “Power liftgate” onpages 5-36, 5-38, 5-40 and 5-42 respectively. Press the driver’s door lock/unlock switch (A) to unlock only the driver’s door. Within approximately 2 seconds, press thedriver’s door lock/unlock switch one more time to unlock all the
doors and the liftgate.
Press the front passenger’s door lock/unlock switch (B) or the liftgate OPEN switch (C) to unlock all the doors and the liftgate.
NOTE
 On the vehicles equipped with the mirror retractor switch, the out
side rearview mirrors
automatically retract when all doors and lift- gate are locked using the driver’s or front passenger’s door lock/unlock switch (A) orthe liftgate LOCK switch (B).  In cases such as the following, the F.A.S.T.- key does not operate. • There is a F.A.S.T.-key in the passenger compartment • A door or the liftgate is open or ajar• The operation mode
is not in OFF.
 The liftgate OPEN switch (C) can be used to confirm that the vehicl
e is locked properly.
Press the liftgate OPEN switch withinapproximately 3 seconds of locking.  If the liftgate OPEN switch is pressed 3 sec- onds or more after the
vehicle is locked, the
doors and the liftga
te are unlocked.
Liftgate switches
The time within which locking confirmation is possible can be adjusted. See an autho-rized Mitsubishi Motors
dealer for details.
On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the function can
be adjusted on the screen. For details, referto the separate owner’s manual.
To u n l o c k

NOTE
NOTE
 On the vehicles equipped with the mirror retractor switch, the out
side rearview mirrors
automatically extend when the driver’s door is unlocked using the
driver’s lock/unlock
switch (A), front passenger’s doorlock/unlock switch (B)
or the liftgate open
switch (C).  Settings can be change
d so that all doors and
the liftgate are unloc
ked automatically by
pressing the driver’s door lock/unlock switchonce. Refer to “Setting of door
and liftgate unlock
function” on page 5-33.Driver’s door lock/unlock switch
BK0278200US.book 18 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-21
5
N00568101137
After approximately 30
minutes has elapsed
with the operation mode
in ACC, the function
automatically cuts out the power for the audio system and other electr
ic devices that can be
operated with that mode.When the engine switch is pressed while the operation mode is in AC
C, the power is sup-
plied again to those devices.
CAUTION When the engine is not running, put the oper- ation mode in OFF. Leaving the operationmode in ON or ACC for a long time whenthe engine is not running may cause the bat- tery to be discharged, making it impossible to start the engine. When the battery is disconnected, the current operation mode is memo
rized. After recon-
necting the battery, the memorized mode is selected automaticall
y. Before disconnect-
ing the battery for re
pair or replacement,
make sure to put the operation mode in OFF. Be careful if you are not sure which opera- tion mode the vehicle is in when the batteryis run down. The operation mode cannot be changed from OFF to ACC or ON if the F.A.S.T.-key is not detected to be in the
vehicle. Refer to “Oper-
ating range for star
ting the engine and
changing the operation mode” on page 5-17. When there is the F.A.S.T.-key in the vehicle and the operation mode
is not changed, the
battery in the F.A.S.T.-key may have worn out.Refer to “Warning acti
vation” on page 5-22.
NOTE
If the operation mode
cannot be changed to
OFF, perform the following procedure. 1. Move the selector lever to the “P” (PARK) position, and then change the operation mode to OFF.
2. One of the other causes could be low bat- tery voltage. If this
occurs, the keyless
entry system, the F.A.S.T.-key operationand steering wheel lock (if so equipped) will also not operate. Contact an authorized Mitsubishi Motorsdealer.
ACC power auto-cutout function

NOTE
 It is possible to modify functions as follows: • The time until the power cuts out can be changed to approximately 60 minutes. • The ACC power auto
-cutout function can
be deactivated.NOTE
For details, we reco
mmend you to consult an
authorized Mitsubish
i Motors dealer.
On vehicles equipped with the Smartphone-link Display Audio (SDA
), screen operations
can be used to make the adjustment. Refer to the separate owner’s manual fordetails.NOTE
BK0278200US.book 21 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-28 Features and controls
5
1. Stop the vehicle. 2. Fully engage the parking brake while depressing the brake pedal. 3. Move the selector
lever to the “P”
(PARK) position, and then press the engine switch to stop the engine.
N00568301142
Insert the F.A.S.T.-key into the key slot in the instrument panel. St
arting the engine and
changing the operation mode should be now possible. Remove the F.A.S.T.-key from the key slotafter starting the engine
or changing the oper-
ation mode.
If the operation mode is in OFF and the driver’s door is opened with the F.A.S.T.-key in the key slot, a warni
ng is issued with the
warning display and
the buzzer buzzing for
approximately 3 seconds to remind you to remove the key.
NOTE
 If you have to bring the engine to an emer- gency stop while driving, press and hold theengine switch for 3 seconds or more, or pressit quickly 3 times or
more. The engine will
stop and the operation m
ode will go to ACC.
 Do not stop the engine wi
th the selector lever
in any position other than the “P” (PARK) position. If the engine is stopped with theselector lever in any
position other than the
“P” (PARK) position, the operation mode will go to ACC rather than OFF.Put the operation mode
in OFF after placing
the selector lever in the “P” (PARK) posi- tion.
If the F.A.S.T.-key is not operat- ing properly

NOTE
 Do not insert into the
key slot anything other
than the F.A.S.T.-key. This could cause dam-age or a malfunction.
 Remove the object or
additional key from the
F.A.S.T.-key before inserting the key into thekey slot. The vehicle may not be able toreceive the registered ID code from the regis- tered key. Therefore, th
e engine may not start
and the operation mode
may not change.
 The F.A.S.T.-key is fixed in the key slot when inserted in the illustrated direction.Simply pull out the key to
remove it from the
key slot.
F.A.S.T.-key reminder

NOTE
BK0278200US.book 28 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced
Security Transmitter (F.A.S
.T.-key) (if so equipped)
5-32 Features and controls
5
Within approximately 2 seconds, press the UNLOCK button one more time to unlock allthe doors and liftgate. The dome light will turn on for 30 seconds. The turn signal lights will also blink twice.The front side-marker and parking lights will also turn on for approximately 30 seconds. Refer to “Welcome light” on page 5-207.
N00544501140
The horn and turn signal lights of the keylessentry system answerback function can be changed as required. This is done with the operation mode in OFF.
N00597200058
The answerback function can be set in thefollowing three ways.Each time the answerback function is set, a chime will sound to tell you the condition of the answerback function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter(F.A.S.T.-key)” on page 5-34.
N00597300059
The answerback function from the turn signallights can be turned ON or OFF separately. Each time the answerback function is set, a chime will sound to
tell you the condition of
the answerback function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter (F.A.S.T.-key)” on page 5-34.
N00597400050
The buzzer answerback function can beturned ON or OFF as required.
NOTE
 If the UNLOCK button (2) is pressed and no doors or the liftgate are opened within approximately 30 seconds, the doors and the liftgate will automatically re-lock.On a vehicle equipped
with the Smartphone-
link Display Audio (SDA), the functions can be adjusted on the scre
en. For details, refer
to the separate owner’s manual.  The door and liftgate
unlock function can be
set so that all doors a
nd liftgate unlock when
the UNLOCK button (2) is pressed once. Refer to “Setting of door
and liftgate unlock
function” on page 5-33.
Answerback function

NOTE
 On a vehicle equipped
with the Smartphone-
link Display Audio (SDA
), the functions can
be adjusted on the screen. For details, referto the separate owner’s manual.

Horn deactivation/reactivation Number of chimes
Condition
One chime The horn will not sound. Two chimes The horn will sound. Four chimes
The horn will sound if the- LOCK button (1) is pressed twice within 1 second.

Turn signal lights deactivation/reac- tivation Number of chimes
To l o c k
To unlock
One chime One flash Two flashes Two chimes One flash No flash Three chimes No flash Two flashes Four chimes Two flashes One flash Five chimes No
flash One flash
Six chimes Two flashes No flash Seven chimes No flash No flash
Buzzer deactivation/reactivation
BK0278200US.book 32 ページ ２０１９年４月１０日　水曜日　午前１０時５９分

Free-hand Advanced Securi
ty Transmitter (F.A.S.T.-key) (if so equipped)
Features and controls 5-33
5
N00544601271
The door and liftgate unlock function can be set to the following two conditions. Each time the door and
liftgate unlock func-
tion is set, a chime will
sound to tell you the
condition of the door and liftgate unlock function. To change the settings, refer to “Customizing the Free-hand Advanced Security Transmitter(F.A.S.T.-key)” on page 5-34.
N00579500020
After unlocking the doors and the liftgate, the power liftgate can be operated by pressing the power liftgate button (3).Refer to “Power lift
gate” on page 5-42.
N00544701142
If you are near your vehicle and feel threat- ened, you can activate the alarm to call atten- tion as follows: 1. Press the PANIC button (4) for more than 1 second. 2. The headlights will blink on and off and the horn will sound intermittently forapproximately 3 minutes. 3. To turn off the alarm, press any button on the remote control transmitter.
Setting the door and liftgate unlock function

Number of chimes
Condition
One chime [Factory setting]
When the UNLOCK button, driver’s or front passenger’s door lock/unlock switch, or liftgate OPEN switch is pressed one time, all doors and the liftgate unlock.
Tw o chimes
When the UNLOCK button or the driver’s door lock/unlock switch is pressed one time, only the driver's door unlocks.When the UNLOCK button or the driver’s door lock/unlock switch is pressed two times in succession, all doors and the liftgate unlock.
Operating the power liftgate

Using the panic alarm

NOTE
 The indicator light (5) comes on each time a button is pressed.  The F.A.S.T.-key can be used from approxi- mately 40 feet (12 m) away. However, this distance may change if
your vehicle is near a
TV transmitting tower, a power station, or a radio station.
 If the following conditions are observed after pressing the LOCK (1) or UNLOCK (2) but-ton on the remote control transmitter, thebattery in the F.A.S.T.-key may need to be replaced. • The doors and the liftgate cannot be locked or unlocked. • The panic alarm
cannot be operated.
• The indicator light
(5) is dim or does not
come on.
 If you lose your F.A.S.T.-key, please contact an authorized Mitsubishi Motors dealer for a replacement.  If you wish to obtain an additional F.A.S.T.- key, please contact an
authorized Mitsubishi
Motors dealer. A maximum of four F.A.S.T.-key can be programme
d for your vehicle.
 To use the new remote control transmitters, it is necessary to register
the key with both the
electronic immobilizer
and keyless entry sys-
tem.Also refer to “Electronic immobilizer (Anti- theft starting system): Customer F.A.S.T.- key programming” on page 5-30.NOTE
BK0278200US.book 33 ページ ２０１９年４月１０日　水曜日　午前１０時５９分