MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

2.Slide the front seats fully forward, then
recline the seatbacks backwards to ach- ieve a flat surface. (Refer to “Front
seats” on page 5-03)
3. Recline the rear seatbacks backwards.
(Refer to “Rear seats” on page 5-05)
4. The flat seat configuration is now com-
plete. Reverse the above procedures
when returning the seat to the normal
position.Seat belts
E00404800867
To protect you and your passengers in theevent of an accident, it is most important that
the seat belts be worn correctly while driving.
The front seat belts have a pretensioner sys- tem. These belts are used the same way as a
conventional seat belt.
Refer to “Seat belt pretensioner system and force limiter system” on page 5-14.
:ARN,NGz Seat belts should always be worn by every
adult who drives or rides in this vehicle,
and by all children who are tall enough to wear seat belts properly.
Other children should always use proper child restraint systems.
z Always place the shoulder belt over your
shoulder and across your chest. Never put
it behind you or under your arm.
z One seat belt should be used by only one
person. Doing otherwise can be danger-
ous.
z The seat belt will provide its wearer with
maximum protection if the recliner seat-
back is placed in fully upright position.
When the seatback is reclined, there is
greater risk that the passenger will slide under the belt, especially in a forward im-
pact accident, and may be injured by the
belt or by striking the instrument panel or seatbacks.
z Remove any twists when using the belt.
z No modifications or additions should be
made by the user which will either pre-
vent the seat belt adjusting devices from operating to remove slack, or prevent theseat belt assembly from being adjusted to
remove slack.
z Never hold a child in your arms or on
your lap when riding in this vehicle, even
if you are wearing your seat belt. To do so risks severe or fatal injury to the child in
a collision or sudden stop.
Seat belts
5-092**((Seats and seat belts5

:ARN,NGzAlways adjust the belt to a snug fit.
z Always wear the lap portion of the belt
over your hips.3-point type seat belt (with
emergency locking mechanism)
E00404902918
This type of belt requires no length adjust- ment. Once worn, the belt adjusts itself to the
movement of the wearer, but in the event of a sudden or strong shock, the belt automatical-
ly locks to hold the wearer’s body.
NOTEz You can check if the belt locks by pulling it
forward quickly.
z If the seat belt buckles in the rear seating po-
sition are not found, you will find them un-
der the rear seat cushion. Refer to “Making a
luggage area” on page 5-06 for how to put
the seat belt buckles at the proper position.
To fasten
1. Pull the seat belt out slowly while hold-
ing the latch plate.
NOTEz When the seat belts cannot be pulled out in a
locked condition, pull the belts once force-
fully and then return them. After that, pull
the belts out slowly once again.
2. Insert the latch plate into the buckle until
a “click” is heard.
:ARN,NGz Never wear the lap portion of the belt
across your abdomen. During accidents it
can press sharply against the abdomen and increase the risk of injury.
z The seat belts must not be twisted when
worn.
3. Pull the belt slightly to adjust slackness
as desired.
To unfasten
Hold the latch plate and push the button on
the buckle.
NOTEz As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could damage the vehicle.
Seat belts
5-102**((Seats and seat belts5

NOTEzIf the seat belt (A) or ring (B) becomes dirty,
the belt may not retract smoothly. If the seat
belt and ring are dirty, clean them with a
mild soap or detergent solution.Seat belt reminder
E00409801973
For the driver and the front passenger’s seat
*-This warning lamp shows the case of the left-hand drive vehicles.
If the operation mode of the power switch is
put in ON while a seat belt is not fastened, the warning lamp comes on and the tone
sounds for about 6 seconds to remind the
driver and the front passenger to fasten the seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamp will blink and
the tone will sound intermittently until the
seat belt is fastened. At the same time, “FAS- TEN SEAT BELT” is displayed on the infor-
mation screen in the multi information dis- play for the driver.:ARN,NGz Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEz If the seat belt subsequently remains unfas-
tened, the warning lamp and the tone will is-
sue further warnings each time the vehicle starts moving from a stop.
z For the front passenger seat, the warning
function works only while a person is sitting
on the seat.
z When luggage is placed on the front passen-
ger seat, a sensor in the seat cushion may,
depending on the weight and position of the
luggage, cause the warning tone to sound
and the warning lamp to come on.
Seat belts
5-112**((Seats and seat belts5 For the driverFor the front passenger

For the rear passenger’s seatsE00415501021
If the operation mode of the power switch isput in ON while a seat belt is not fastened,
the warning lamp comes on for approximate-
ly 30 seconds to remind the rear passenger to fasten the seat belt.
If the vehicle is driven with the seat belt still
unfastened, the warning lamps come on for
approximately another 30 seconds. (This illu-
mination happens only the first time the vehi- cle starts moving with the seat belt still un-
fastened.)
The warning lamps go off when the seat belt is fastened.
:ARN,NGz Do not install any accessory or sticker
that makes the lamp difficult to see.NOTEz The warning lamp comes on even if no one
is sitting on the rear seats.
z If a seat belt is unfastened while the vehicle
is being driven, the tone sounds for approxi- mately 1 second and the warning lampcomes on for approximately 30 seconds. At the same time, the warning lamp for the seat
where the seat belt is not fastened comes on.
z If the seat belts are initially fastened but a
seat belt is unfastened while the vehicle is
stationary and the vehicle is then driven with the seat belt still unfastened, the warning
lamp comes on again for approximately 30 seconds.Adjustable seat belt anchor
(front seats)
E00405000420
The seat belt anchor height can be adjusted.
Move the seat belt anchor down with the lock knob (A) depressed. To move the anchor up,
slide it without depressing the lock knob (A).:ARN,NGz When adjusting the seat belt anchor, set it
at a position that is sufficiently high so
that the belt will make full contact with your shoulder but will not touch your
neck.
Seat belts
5-122**((Seats and seat belts5

Rear-centre 3-point type seatbelt
E00405201184
The rear-centre 3-point type seat belt must be
worn correctly as illustrated.
:ARN,NGz Be sure to securely connect the both latch
plate (A and B). Failing to do so could sig-
nificantly reduce the amount of protection
and cause serious injures in a collision or a sudden stop.NOTEz If the seat belt buckles in the rear seating po-
sition are not found, you will find them un-
der the rear seat cushion.
Refer to “Making a luggage area” on page 5-06 for how to put the seat belt buckles at
the proper position.To fasten
1. Pull out the buckle (C) from the seat-
back.
2. Pull out the small latch plate (A) and
then pull out the latch plate (B) by tilting it as shown in the illustration.
NOTEz Pulling out the latch plate by force may
damage the headliner.
3. Pull the seat belt and insert the small
latch plate (A) into the buckle (C).
4. Insert the latch plate (B) into the buckle
(D).
5. Pull the belt slightly to adjust slackness
as desired.
To unfasten
1. Hold the latch plate and push the button
on the buckle.
NOTEz As the belt retracts automatically, keep hold-
ing the latch plate while retracting so that the
belt stows slowly. Failure to do this could damage the vehicle.
z To release the buckle (C), press the button
(E) with a narrow-tipped object (latch plate
or mechanical key etc.).
Seat belts
5-132**((Seats and seat belts5AA0111461

2.After the seat belt is retracted complete-
ly, insert the latch plate (B) into the up-
per slit (F), and then insert the small
latch plate (A) into the lower slit (G).
3. Store the seat belt buckle in the storage
pocket.
(Refer to next column.)
Rear seat belt storage
E00405301521
When the seat belt is not in use, store it as
shown in the illustration.
Seat belt plate storage
Outboard seating position
After passing the belt through the rear notch
(A), insert the plate into the front notch (B).
Pregnant women restraint
E00405600077:ARN,NGzSeat belts work for everyone, including
pregnant women. Pregnant women should use the available seat belts. This will re-
duce the likelihood of injury to both the woman and the unborn child. The lap belt should be worn across the thighs and as
snug against the hips as possible, but not across the waist. Consult your doctor if
you have any additional questions or con- cerns.Seat belt pretensioner
system and force limiter system E00405701323
The driver’s seat and front passenger’s seateach have a seat belt equipped with a preten- sioner system and force limiter system.
Pregnant women restraint
5-142**((Seats and seat belts5 AA0111487 AA0064860

Pretensioner system
E00405802523
When the operation mode of the power
switch is in ON, if there is a frontal impact or
a side impact severe enough to injure the driver and/or front passenger, the pretension-
er system will retract their respective seat
belts instantaneously, thus maximizing the seat belt’s effectiveness.
:ARN,NGz To obtain the best results from your pre-
tensioner seat belt, make sure you have adjusted your seat correctly and wear your seat belt properly.CAUT,ONz Installation of audio equipment or repairs in
the vicinity of the pretensioner seat belts or
floor console must be performed in line with MITSUBISHI MOTORS guidelines. It is
important to do so because the work could affect the pretensioner systems.
z If you need to scrap the vehicle, please con-
sult a MITSUBISHI MOTORS Authorized
Service Point.
It is important to do so because unexpected activation of the pretensioner seat belts
could cause injuries.NOTEz The pretensioner seat belts will be activated
if the vehicle suffers a severe impact, even if
the seat belts are not worn.
z The pretensioner seat belts are designed to
work only once. After the pretensioner seat
belts have been activated, we recommend
you have it replaced by a MITSUBISHI
MOTORS Authorized Service Point.SRS warning
E00405900360
The same warning lamp/display is shared by
the SRS airbags and the pretensioner seat
belts.
Refer to “SRS warning lamp/display” on page 5-35.
Force limiter system
E00406000209
In the event of a collision, each force limitersystem will effectively absorb the load ap- plied to the seat belt to minimize the impact
to the passenger.
Child restraint
E00406403507
When transporting children in your vehicle,some type of child restraint system should al- ways be used according to the size of the
child. This is required by law in most coun- tries.
The regulations concerning driving with chil-
dren in the front seat may differ from country to country. You are advised to comply with
the relevant regulations.:ARN,NGz When possible, put children in the rear
seat. Accident statistics indicate that chil- dren of all sizes and ages are safer when
properly restrained in the rear seat rather than in the front seat.
z Holding a child in your arms is no substi-
tute for a restraint system. Failure to use
a proper restraint system can result in se- vere or fatal injury to the child.
z Each child restraint device or fixing is to
be used only by one child.
z When attaching a child restraint system
to the rear seat, prevent the front seat-
backs from touching the child restraint system.
Otherwise, the child could be seriously in-
jured in the event of hard braking or a collision.
Child restraint
5-152**((Seats and seat belts5

Caution for installing the childrestraint on vehicles with frontpassenger’s airbag
The label shown here is attached on vehicles with a front passenger’s airbag.
:ARN,NGz Extreme Hazard!
NEVER use a rearward facing child re- straint on a seat protected by an ACTIVEAIRBAG in front of it, DEATH or SERI-
OUS INJURY to the CHILD can occur.Use rearward facing child restraints in the
rear seat or turn off the front passenger’s air- bag ON-OFF switch. (Refer to “To turn anairbag off” on page 5-28):ARN,NGz A REARWARD FACING CHILD RE-
STRAINT must NOT be used in the front passenger seat if the front passenger’s air-bag has not been deactivated. The force of
an inflating airbag could kill or cause se- rious injuries to the child. A rearward
facing child restraint should be used in
the rear seat.
z A FORWARD FACING CHILD RE-
STRAINT should be used in the rear seat
whenever possible; if it must be used in
the front passenger seat, turn off the front
passenger’s airbag ON-OFF switch.
Failure to do so could kill or cause serious
injuries to the child.:ARN,NGz A REARWARD FACING CHILD RE-
STRAINT must NOT be used in the front passenger seat when the driver’s visibility
is obstructed.Infants and small children
E00406602065
When transporting infants and small children
in your vehicle, follow the instruction given below.
Instruction:
z For small infants, an infant carrier
should be used. For small children whose height when seated allows the shoulder belt to lie in contact with the
face or the throat, a child seat should be used.
Child restraint
5-162**((Seats and seat belts5 Front passenger’s
airbag ON

zThe child restraint system should be ap-
propriate for the child’s weight and height and properly fit in the vehicle.
For a higher degree of safety: THE CHILD RESTRAINT SYSTEM
SHOULD BE INSTALLED IN THE REAR SEAT.NOTEz Before purchasing a child restraint system,
try installing it to make sure there is a good fit. Because of the location of the seat belt
buckles and the shape of the seat cushion, it may be difficult to securely install some
manufacturer’s child restraint systems.
If the child restraint system can be pulled forward or to either side easily on the seatcushion after the seat belt has been tight-
ened, choose another manufacturer’s child restraint system.:ARN,NGz When installing a child restraint system,
refer to the instructions provided by the manufacturer of the restraint system.
Failure to do so can result in severe or fa- tal injury to the child.:ARN,NGz After installation, push and pull the child
restraint system back and forth, and sideto side, to see that it is properly secured. If
the child restraint system is not installed
securely, it may cause injury to the child or other occupants in the case of accident or sudden stops.
z When the child restraint system is not in
use, keep your child restraint system se- cured with the seat belt or remove it from the vehicle in order to prevent it from be-
ing thrown around inside the vehicle dur- ing an accident.
Depending on the seating position in the
vehicle and the child restraint system
that you have, the child restraint can be attached using one of the following two
ways:

Suitability for various ISOFIX positions
E00411402393
Mass groupSize
classFixture
Vehicle ISOFIX positionsRecom-
mended ChildRe-
straint Sys-
tems *2
UN-R44 Ap-
proval No.
UN-
R129
Appro- val No.
Front passenger
Rear out- boardActivated air- bagDeactivated Airbag *1
CarrycotFISO/L1XXX———GISO/L2XXX———0 -Up to 10 kgEISO/R1XILIL———0+ -Up to 13 kgEISO/R1XILIL———
DISO/R2XIL, IL#IL, IL#
BABY-
SAFE i- SIZE:
MZ3150 55
BABY-
SAFE i- SIZE
FLEX
BASE:
MZ3150 56
—E1-000008
CISO/R3XXIL———I -9 to 18 kgDISO/R2XXIL———CISO/R3XXIL———
Child restraint
5-182**((Seats and seat belts5