MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

NOTEzDepending on the state of the vehicle (such
as during heating of the air conditioner), the engine may start even if the needle of the en-
ergy usage indicator is indicated before zone
2 (the zone that the engine starts in high pos- sibility).
z Even when the EV priority mode is selected
and the engine does not start, the needle of the energy usage indicator may indicate zone
2 (the zone that the engine starts in high pos- sibility).
z When the EV priority mode is selected, even
if the needle of the energy usage indicator
enters zone 2, it will not start the engine un- less it is over the specified point by pressing
the accelerator pedal.
z Depending on the vehicle condition, the
movement of the needle of the energy usage
indicator may be different or fluctuate.
z Economical driving can be achieved by op-
erating in such state that the swing of the needle is small within zone 1.
Charge zone
Indicates the charging power generated by
the regenerative brake.
The more the needle moves, the more electric energy is charged.
The needle of the energy usage indicator may not enter the charge zone when the drive bat-
tery is close to full charge.
Also, if the needle of the energy usage indi-
cator indicates the engine output zone, the needle does not indicate the charge zone even
when there is charging of the electrical ener-
gy by regenerative braking.NOTEz With the charging power gauge of the multi
information display, you can check thecharging power of electric energy generated
by regenerative braking even while the en- gine is operating.
z Both the display of the charge zone by the
energy usage indicator needle and the dis- play of the charging power gauge in the mul-
ti information display indicate the charging power of electric energy by regenerative
braking.
Engine output zone
Indicates the instantaneous output (kW) of
the engine.
Meter illumination control
E00531301174
Each time you press the rheostat illumination
button, there is a sound and the brightness of
the instruments changes.
1- Brightness level
2- Rheostat illumination button
NOTEz You can adjust to 8 different levels respec-
tively for when the position lamps are illu- minated and when they are not.
z When the lamp switch is in a position other
than the “OFF” position, the meter illumina-
tion switches automatically to the adjusted brightness, depending on the brightness out- side the vehicle.
Instruments
6-032**((Instruments and controls6

NOTEzThe brightness level of the instruments is
stored when the operation mode of the pow-
er switch is put in OFF.
z If you press and hold the button for about 2
seconds or more when the position lamps are
illuminated, the brightness level changes to
the maximum level. Pressing and holding the button for about 2 seconds or more again returns the brightness level to the previous
level.
On vehicles equipped with the
MITSUBISHI Multi-Communication Sys-
tem (MMCS), the map screen colour of MITSUBISHI Multi-Communication Sys-
tem (MMCS) may not be switched to night- time setting when the meter illumination
brightness level is at the maximum.Multi information display
E00519903158
Always stop the vehicle in a safe place before operating.
The following information is included on the multi information display: warnings, odome-
ter, tripmeter, average fuel consumption, EV cruising range, total cruising range, EVHV
driving rate, energy flow, etc.[When the operation mode of the power switch is OFF@
1- mark display screen o p. 6-11
2- Information screen o p. 6-07
Interrupt display screen o p. 6-10
3- Drive battery level display screen
o p. 6-11
4- Odometer o p. 6-13
5- “
” or “ ” mark indicator o p. 6-10
Multi information display
6-042**((Instruments and controls6

6-Door ajar warning display screen
o p. 6-11NOTEz The drive battery level display screen ap-
pears when any of the doors or the tailgate is
opened during charging.[When the operation mode of the power
switch is ON@1- NORMAL mode indicator display
2- SNOW mode indicator display
3- LOCK mode indicator display S-AWC (Super All Wheel Control)
o p. 7-20
4- ECO mode indicator display ECO mode switch o p. 6-68
5- SPORT mode indicator display SPORT mode switch o p. 7-316- Battery charge mode display screen
o p. 7-29
7- Battery save mode display screen
o p. 7-29
8- EV priority mode display screen
o p. 7-25
9-
mark display screen o p. 6-11
10- Forward Collision Mitigation System
(FCM) OFF display screen* o p. 7-67
Ultrasonic misacceleration Mitigation System (UMS) OFF display screen*
o p. 7-77
11- Lane Departure Warning (LDW) display
screen* o p. 7-88
12- Cruise control display screen*
o p. 7-45
Multi information display
6-052**((Instruments and controls6

13-Adaptive Cruise Control System (ACC)
display screen* o p. 7-55
14- Speed limiter display screen*
o p. 7-50
15- Drive battery level display screen
o p. 6-11
16- Odometer o p. 6-13
17- “
” or “ ” mark indicator o p. 6-10
18- Information screen o p. 6-09
19- Select position indicator o p. 7-17
20- Fuel remaining display screen
o p. 6-11
21- Outside temperature display screen
o p. 6-13
22- Charging power gauge o p. 6-12
Multi information display
switch
E00520001911
Each time the multi information display
switch is operated, the buzzer sounds and the multi information display changes between
information such as warnings, tripmeter, average fuel consumption, EV cruising range,
total cruising range, EVHV driving rate, en-
ergy flow, etc.
It is also possible to change elements such as
the language and units used on the multi in-formation display by operating the multi in-
formation display switch.
Multi information display
6-062**((Instruments and controls6

Information screen (when the operation mode is OFF)
E00520201968
Each time you lightly press the multi information display switch, the display screen switches in the following order.
* 1
: When there is no warning display
* 2
: When there is a warning display
1- Tripmeter o p. 6-13
2- Tripmeter
o p. 6-13
3- ECO score display o p. 6-17
4- Predicted charging time o p. 3-10, 3-17
5- Service reminder o p. 6-136- Redisplay of a warning display screen
o p. 6-10

Multi information display
6-072**((Instruments and controls6* 2*1

Information screen (when the operation mode is changed from OFF to ON)
E00520702351
When the operation mode is put in ON, the display screen switches in the following order.
* 1
: When the inspection time has arrived
1- Screen when the operation mode is OFF
2- System check screen o p. 6-153- Screen when the operation mode is ON
4- Service reminder o p. 6-13

Multi information display
6-082**((Instruments and controls6

Information screen (when the operation mode is ON)
E00521102192
Each time you lightly press the multi information display switch, the display screen switches in the following order.
* 1
: When the vehicle is charged
* 2
: When there is no warning display
* 3
: When there is a warning display
1- Tripmeter o p. 6-13
2- Tripmeter
o p. 6-13
3- EV cruising range display/Total cruising range display o p. 6-15
4- Average fuel consumption display o p. 6-16
EVHV driving rate display o p. 6-16
5- Energy flow display o p. 6-16
or
Energy flow display during charging
o p. 3-26
6- ECO score display o p. 6-17
7- S-AWC (Super-All Wheel Control) op- eration display o p. 7-228- Service reminder o p. 6-13
9- Function setting screen o p. 6-17
10- Redisplay of a warning display screen o p. 6-10
Multi information display
6-092**((Instruments and controls6or

NOTEzWhile driving, the service reminder is not displayed even if you operate the multi information display switch. Always stop the vehicle in a safe place before
operating.
z While driving, the function setting screen is not displayed even if you operate the multi information display switch.
Before operation, park the vehicle in a safe place, firmly apply the parking brake, press the electrical parking switch, and shift to “P” (PARK) position.
Refer to “Changing the function settings” on page 6-17.
z When there is information to be announced, such as a system fault, the buzzer sounds and the screen display is switched.
Refer to “Interrupt display screen” on page 6-10.

Interrupt display screen
E00522002084
Warning display
When there is information to be announced, such as a system fault, the buzzer sounds and the information screen is switched to the
warning display screen.
Refer to the warning list and take the neces-
sary measures.
Refer to “Warning display list” on page
6-26.
When the cause of the warning display is eliminated, the warning display goes out au-tomatically.
To return to the screen dis-
played before the warning dis- play
Even if the cause of the warning display isnot eliminated, you can return to the screen
that was displayed before the warning dis- play.
If you press the multi information display
switch, the display screen switches to the screen that was displayed before the warning
display and the
mark (A) is displayed.
If you want to switch the dis-
play
Warning display screens with a “” or “”
mark displayed in the upper right of the
screen can be switched. If you want to switch the display, press the multi information dis-
play switch as follows.
“
”: Press lightly.
“
”: Press for approximately 2 seconds or
more.
Redisplay of a warning display screen
When the mark is displayed, if you lightly
press the multi information display switch a
few times, the warning display screen you
switched from is redisplayed.
Other interrupt displays
The operation status of each system is dis-
played on the information screen.
Multi information display
6-102**((Instruments and controls6

Refer to the appropriate page in the warningdisplay list for further details.
Refer to “Other interrupt displays” on page
6-48. mark display screen
E00533901028
This is displayed when you press the multi information display switch and return from
the warning display screen to the previous screen.
This mark is also displayed if there is another
warning other than the one displayed.
When the cause of the warning display is
eliminated, the
mark goes out automatical-
ly.
NOTEz When the mark is displayed, the warning
display screen can be redisplayed on the in- formation screen.
Refer to “Information screen (when the op-
eration mode is OFF)” on page 6-07.
Refer to “Information screen (when the op-
eration mode is ON)” on page 6-09.Door ajar warning display
screen
E00522601979
If any of the doors or the tailgate is not com-
pletely closed, this displays the open door or
tailgate.
When the operation mode of the power switch is ON, if the vehicle speed exceeds
approximately 8 km/h (5 mph) while a door is ajar, a buzzer sounds 4 times. This notifies
the driver that a door is ajar.
CAUT,ONz Before moving your vehicle, check that the
warning display does not appear.Drive battery level display
screen
E00537700027
Indicates the remaining pow-
er in the drive battery.
Fuel remaining display screen
E00522201542
This displays the amount of fuel remaining.
F- Full
E- Empty
Multi information display
6-112**((Instruments and controls6

NOTEzIt may take several seconds to stabilise the
display after refilling the tank.
z If fuel is added with the operation mode of
the power switch is in ON, the fuel gauge may incorrectly indicate the fuel level.
z The arrow (A) indicates that the fuel tank
filler is located on the left side of the body.Fuel remaining warning display
E00522402495
When the fuel is reduced to approximately 7
litres, the information screen switches to the
interrupt display of the fuel remaining warn- ing display, and the “
” mark (B) on the fuel
remaining display flashes slowly (approxi-
mately once per second). After a few sec- onds, the information screen returns from the
fuel remaining warning display to the previ- ous screen.
If the remaining fuel level is reduced further,
the information screen switches to the fuel re-
maining warning display and the “
” mark
(B) on the fuel remaining display flashes
quickly (approximately twice per second).
CAUT,ONz If the warning display appears, refuel as
soon as possible.
If the vehicle runs out of fuel, the engine will not start even in a situation need to be
generated electricity, the following condi- tions will occur.