MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

NOTEzThe charging power gauge does not include
the electric power generation by the engine
operation.
z The charging power gauge does not indicate
the running condition of
bat-
tery charge.
z The movement of the gauge decreases as the
drive battery level is nearly full.
Outside temperature display
screen
E00522101509
This shows the temperature outside the vehicle.
NOTEz The display setting can be changed to the
preferred units (

NOTEzThe distance is shown in units of 100 km
(100 miles). The time is shown in units of months.
2. This informs you that a periodic inspec-
tion is due. We recommend you to con-
sult a MITSUBISHI MOTORS Author-
ized Service Point.

At that time, when the ignition switch is switched from “OFF” to “ON”, the
warning display is displayed for a few seconds on the information screen.
3. After your vehicle is inspected at a
MITSUBISHI MOTORS Authorized
Service Point, it displays the time until the next periodic inspection.
To reset
The “---” display can be reset while the igni- tion switch or the opertion mode is in OFF.
When the display is reset, the time until the
next periodic inspection is displayed and the warning display is no longer displayed when
the ignition switch is switched from “OFF” to
“ON”. 1. When you lightly press the multi infor-
mation display switch a few times, the information display switches to the serv-
ice reminder display screen.
2. Press and hold the multi information dis-
play switch for about 2 seconds or more
to display “
” and make it flash. (If
there is no operation for about 10 sec- onds with flashing, the display returns tothe previous screen.)
3. Lightly press the multi information dis-
play switch while the icon is flashing to
change the display from “---” to
“CLEAR”. After this, the time until the
next periodic inspection will be dis- played.CAUT,ONz The customer is responsible for making sure
that periodic inspection and maintenance are
performed.
Inspections and maintenance must be per- formed to prevent accidents and malfunc- tions.NOTEz “---” display cannot be reset when the opera-
tion mode is in ON.
Multi information display
6-142**((Instruments and controls6

NOTEzWhen “---” is displayed, after a certain dis-
tance and a certain period of time, the dis-
play is reset and the time until the next peri- odic inspection is displayed.
z If you accidentally reset the display, we rec-
ommend you to consult a MITSUBISHI
MOTORS Authorized Service Point.System check screen
E00531001070
When the operation mode is put in ON, the
system check screen is displayed for about 4
seconds. If there is no fault, the information screen (when the operation mode is ON) is
displayed.
If there is a fault, the screen changes to warn-
ing display.
Refer to “Warning display list” on page
6-26.
NOTEz The system check screen display varies de-
pending on the customer’s equipment.EV cruising range display/
Total cruising range display
E00537600042
This displays the approximate driving range
(how many more kilometres or miles you can drive).
EV cruising range display (A)
This displays the distance that can be traveled
with the remaining power in the drive battery.
Total cruising range display (B)
This displays the distance that can be traveled
with the remaining power in the drive battery and the remaining amount of fuel.
NOTEz The EV cruising range may vary depending
on the driving conditions and your personal
driving habits.
The EV cruising range is calculated from the
following information.

NOTEzOn rare occasions, the value displayed for
the driving range may change if you areparked on an extremely steep incline. This is
due to the movement of fuel in the tank and
does not indicate a malfunction.
z The display setting can be changed to the
preferred units (km or miles).
Refer to “Changing the function settings” on page 6-17.
z When the EV cruising range falls below ap-
proximately 1 km (1 mile), the EV cruising range display shows “---”.
z When the total cruising range falls below ap-
proximately 50 km (30 miles), the total
cruising range display shows “---”.Average fuel consumption dis-
play
E00531201128
This displays the average fuel consumption from the last reset to the present time.
There are the following 2 mode settings.
Refer to “Changing the reset mode for aver-
age fuel consumption” on page 6-18.
For information on how to change the aver-
age fuel consumption display setting, refer to “Changing the function settings” on page
6-17.
NOTEz The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
z “---” is displayed when the average fuel con-
sumption cannot be measured.
z The initial (default) setting is “Auto reset
mode”.
z The average fuel consumption depends on
the driving condition (road condition, driv- ing behavior, etc.). The displayed fuel con- sumption may vary from the actual fuel con-
sumption. Treat the fuel consumption dis- played as just a rough guideline.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con-sumption display is erased if the auxiliary
battery is disconnected.
z The display setting can be changed to the
preferred units {km/L, mpg (US), mpg (UK)
or L/100 km`.
Refer to “Changing the function settings” on page 6-17.EVHV driving rate display
E00537500038
This displays the ratios of the time travelled
with electric power and the time travelledwith both electric power and engine power.
The ratio of the time traveled with electric
power is displayed with a bar graph (blue) and in a percentage.NOTEz When the drive battery is fully charged,
EVHV driving rate is reset and display be-comes 100 %.Energy flow display
E00537400040
This displays the flow of energy.
A- Engine
B- Drive battery
C- Tyre
Multi information display
6-162**((Instruments and controls6

Blue arrow-Flow of electric en-
ergyAmber arrow-Flow of other energy
Display of energy flow (exam-
ple)
When driving with electric energy
When driving with fuel (petrol) energy
When driving with both electric energy
and fuel (petrol) energy
When charging the drive battery
When there is no energy flow
NOTEz During charging, the energy flow display for
charging is displayed. For details, refer to
“Energy flow display during charging” on page 3-26.ECO Score
E00531601207
ECO score indicates the points you have
scored on fuel-efficient driving by the num-
ber of leaves as follows:

[When the operation mode is ON@
The display shows the score you achieved in the last several minutes.

[When the operation mode is put in OFF@
The display shows the overall ECO score the
function has counted from the time when the operation mode is set to “ON” to the time when it is set to “OFF”.Changing the function settings
E00522702254
The “Display language”, “Temperature unit”, “Fuel consumption unit”, and “Average fuelconsumption and speed reset method” etc.
setting can be modified as desired. 1. Stop the vehicle in a safe place. Firmly apply the parking brake, and
press the electrical parking switch and shift to “P” (PARK) position.
2. Lightly press the multi information dis-
play switch a few times to switch the in- formation screen to the function setting
screen.
Multi information display
6-172**((Instruments and controls6 ECO drive level
Low High

Refer to “Information screen” on page
6-09.CAUT,ONz For safety, stop the vehicle before operating.
While driving, even if you operate the multi information display switch, the function set- ting screen is not displayed.
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
NOTEz To return the menu screen to the function
setting screen, press and hold the multi in-formation display switch for about 2 seconds or more.
z If no operations are made within about 30
seconds of the menu screen being displayed, the display returns to the function settingscreen.
4. Select the item to change on the menu
screen and change to the desired setting. Refer to the following items for further
details on the operation methods.

Refer to “Changing the reset mode for
average fuel consumption” on page
6-18.
Refer to “Changing the fuel consump- tion display unit” on page 6-19.
Refer to “Changing the temperature
unit” on page 6-20.
Refer to “Changing the display lan- guage” on page 6-20.
Refer to “Changing the language cooper-
ative control” on page 6-21.
Refer to “Operation sound setting” on
page 6-21.
Refer to “Changing the time until “REST REMINDER” is displayed” on
page 6-22.
Refer to “Changing the turn-signal
sound” on page 6-22.
Refer to “Reset of low tyre pressure
warning threshold” on page 7-96.
Refer to “Tyre ID set change” on page
7-96.
Refer to “Reset of EV/Total cruising range” on page 6-22
Refer to “Returning to the factory set-
tings” on page 6-22.NOTEz If the auxiliary battery is disconnected, these
function settings are reset from memory and
return automatically to the factory settings (except the low tyre pressure warning threshold and tyre ID set).Changing the reset mode for
average fuel consumption
E00522902243
The mode conditions for the average fuel consumption display can be switched be- tween “Auto reset” and “Manual reset”. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
Multi information display
6-182**((Instruments and controls6

2.Lightly press the multi information dis-
play switch to select “AVG (average fuel
consumption)”.
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from A/1 (Auto reset mode) to M/2/P (Manual reset mode), or fromM/2/P to A/1.
The setting is changed to the selected
mode condition.
Manual reset mode
z When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the
average fuel consumption displayed at that time is reset.
z When the operation mode is changed
from ACC or OFF to ON, the mode set- ting is automatically switched from man-
ual to auto.
Switching to auto occurs automatically.
If switching to manual mode is done, however, the data from the last reset isdisplayed.
Auto reset mode
z When the average fuel consumption is
being displayed, if you hold down the multi-information meter switch, the
average fuel consumption displayed at that time is reset.
z When the operation mode is in ACC or
OFF for about 4 hours or longer, the average fuel consumption display is au-
tomatically reset.
NOTEz The average fuel consumption display can
be reset separately for the auto reset mode and for the manual reset mode.
z The memory of the auto reset mode or man-
ual reset mode for the average fuel con- sumption display is erased if the auxiliarybattery is disconnected.Changing the fuel consumption
display unit
E00523001778
The display unit for fuel consumption can be
switched. The distance and amount units are also switched to match the selected fuel con- sumption unit. 1. Press and hold the multi information dis-
play switch for about 2 seconds or moreto switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select “AVG UNIT (fuel
consumption display setting)”.
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to display “AVG UNIT”.
Multi information display
6-192**((Instruments and controls6

4.Lightly press the multi information dis-
play switch to select the units.
5. Press and hold the multi information dis-
play switch for about 2 seconds or more to change the setting to the selected unit.NOTEz The display units for the average fuel con-
sumption and the driving range is switched, but the units for the indicating needle
(speedometer), the odometer and the tripme-
ter will remain unchanged.
The distance units is also switched in the fol-
lowing combinations to match the selected
fuel consumption unit.
Fuel consumptionDistance (driving
range)L/100 kmkmmpg (US)mile(s)mpg (UK)mile(s)km/LkmChanging the temperature unit
E00523101913
The display unit for temperature can beswitched.
1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select “
” (temperature
unit setting).
3. Press and hold the multi information dis-
play switch for about 2 seconds or more
to switch in from

5.If you hold down the multi information
display switch for about 2 seconds or
more, the setting is changed to the selec- ted language.NOTEz If “---” is selected in the language setting, a
warning message is not displayed whenthere is a warning display or interrupt dis-
play.Changing the language cooper-
ative control
E00523301827
The language used in MITSUBISHI Multi-
Communication System (MMCS) (if so
equipped), Bluetooth

Changing the time until “RESTREMINDER” is displayed
E00523501702
The time until the display appears can be
changed. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select “ALARM” (rest time setting).
3. Press and hold the multi information dis-
play switch for about 2 seconds or more to display “ALARM”.
4. Lightly press the multi information dis-
play switch to select the time until thedisplay.
5. Press and hold the multi information dis-
play switch for about 2 seconds or more, the setting is changed to the selected
time.
NOTEz The drive time is reset when the operation
mode of the power switch is put in OFF.Changing the turn-signal soundE00529100396
It is possible to change the turn-signal sound.
1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select
(changing the
turn-signal sound).
3. Press and hold the multi information dis-
play switch for about 2 seconds or moreto switch from 1 (turn-signal sound 1) to
2 (turn-signal sound 2), or from 2 to 1.
The setting changes to the selected turn-
signal sound.
Reset of EV/Total cruising
range
E00532200027
The learned value for EV cruising range re- sets to the initialized value. 1. Press and hold the multi information dis-
play switch for about 2 seconds or moreto switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set-
tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select “
RESET” (Reset of EV cruising range).
3. When you press and hold the multi in-
formation display switch for about 3 sec- onds or more, the buzzer sounds and thelearned value resets to the default values.Returning to the factory set-
tings
E00523602205
Many of the function settings can be returned
to their factory settings. 1. Press and hold the multi information dis-
play switch for about 2 seconds or more to switch from the setting mode screen
to the menu screen.
Refer to “Changing the function set- tings” on page 6-17.
2. Lightly press the multi information dis-
play switch to select “
RESET” (returning to the factory set-
tings).
3. When you press and hold the multi in-
formation display switch for about 5 sec- onds or more, the buzzer sounds and allof the function settings are returned to
the factory settings.
NOTEz The factory settings are as follows.