MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

ScreenCauseSolution (Reference)
zThere is a fault in the Lane Departure
Warning (LDW).z We recommend you to have it checked.
Refer to “Lane Departure Warning
(LDW)” on page 7-88.
z The Ultrasonic misacceleration Mitigation
System (UMS) sensor is temporarily not available for some reason such as the en-
vironmental condition or increase of the sensor temperature.z When the warning display does not disap-
pear after waiting for a while, contact a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti- gation System (UMS)” on page 7-77.
Indication lamp, warning lamp, and information screen display list
6-432**((Instruments and controls6

ScreenCauseSolution (Reference)
zThe Ultrasonic misacceleration Mitigation
System (UMS) does not operate normally
because there are some malfunctions in the sensor or the system.z Immediately have your vehicle inspected
at a MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Ultrasonic misacceleration Miti-
gation System (UMS)” on page 7-77.
z The Ultrasonic misacceleration Mitigation
System (UMS) is activated.z Refer to “Ultrasonic misacceleration Miti-
gation System (UMS)” on page 7-77.
Indication lamp, warning lamp, and information screen display list
6-442**((Instruments and controls6

ScreenCauseSolution (Reference)
zThe Blind Spot Warning (BSW) sensor is
temporarily not available for some reason such as the environmental condition or in-crease of the sensor temperature.
z When the warning display does not disap-
pear after waiting for a while, contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW)” on page 7-82.
z The Blind Spot Warning (BSW) does not
operate normally because there are some malfunctions in the sensor or the system.z We recommend you to have it checked,
immediately.
Refer to “Blind Spot Warning (BSW)” on
page 7-82.
z Foreign objects, such as dirt, snow or ice,
adhere to the bumper surface around the sensor.
z Remove a foreign object on the bumper
surface around the sensor.
When the warning display does not disap- pear after having cleaned the bumper sur-face around the sensor, contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Blind Spot Warning (BSW):
When there is a foreign objects on the
sensor” on page 7-86.
z The Rear Cross Traffic Alert (RCTA) has
detected a vehicle that is approaching
your vehicle.z Pay special attention to the rear of your
vehicle.
Refer to “Rear Cross Traffic Alert (RCTA)” on page 7-86.
Indication lamp, warning lamp, and information screen display list
6-452**((Instruments and controls6

ScreenCauseSolution (Reference)
zThere is a fault in the sensor.
zWe recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Forward Collision Mitigation
System (FCM): When a problem is detec- ted” on page 7-73.
Refer to “Lane Departure Warning
(LDW): System problem warning” on page 7-90.
Refer to “Automatic High-Beam (AHB):
System problem warning” on page 6-64.
z The Forward Collision Mitigation System
(FCM), Lane Departure Warning (LDW)and Automatic High-Beam (AHB) are
temporarily unavailable due to the high or low temperature of the sensor.
z After the temperature of the sensor has
been in range, the system will automati-
cally return to operation.
Refer to “Forward Collision Mitigation System (FCM): When a problem is detec-
ted” on page 7-73.
Refer to “Lane Departure Warning (LDW): System problem warning” onpage 7-90.
Refer to “Automatic High-Beam (AHB):
System problem warning” on page 6-64.
z The sensor is temporarily unavailable due
to conditions such as the adhesion of con- taminants to the sensor or windscreen.This is not a malfunction.
Refer to “Forward Collision Mitigation System
(FCM): When a problem is detected” on page
7-73.
Refer to “Lane Departure Warning (LDW):
System problem warning” on page 7-90.
Refer to “Automatic High-Beam (AHB): Sys-
tem problem warning” on page 6-64.
Indication lamp, warning lamp, and information screen display list
6-462**((Instruments and controls6

ScreenCauseSolution (Reference)
zThere is a fault in the Automatic High-
Beam (AHB).
z We recommend you to contact a
MITSUBISHI MOTORS Authorized
Service Point.
Refer to “Automatic High-Beam (AHB): System problem warning” on page 6-64.

Navigation information dis-
play*
E00531401061
On vehicles equipped with MITSUBISHI
Multi-Communication System (MMCS), the following information on navigation will be
displayed when guidance location such as junction and destination is approached afteryou set the destination and started the route
guidance.
1- Guidance displayShows the direction of vehicle travel and the guidance location.
Indication lamp, warning lamp, and information screen display list
6-472**((Instruments and controls6 Direction of vehicle travel (Example) Destination Ferry terminal Tollbooth Intermediate destination (Example)

2- Remaining distance displayShows the distance to the location where
the guidance is displayed.NOTEz Please read this section and also the separate
owner’s manual for MITSUBISHI Multi-
Communication System (MMCS).Other interrupt displays
E00524202556
ScreenCauseSolution (Reference)z When you pressed the power switch and
the operation mode become the ACC
without depress the brake pedal, this
screen is displayed.
This screen will be displayed repeatedly at regular intervals while the operation mode of the power switch is put in ACC.z Place the select position in the “P” (PARK)
position, depress the brake pedal more
firmly than usual with the right foot. Then,
press the power switch.
Refer to “Starting and stopping the Plug-in Hybrid EV System” on page 7-13.z When Plug-in Hybrid EV System does
not start even if the operation mode of the
power switch is put in ON, this screen is displayed.z When starting the Plug-in Hybrid EV Sys-
tem, you pressed the power switch with- out select position in the “P” (PARK) po-
sition.z Place the select position in the “P”
(PARK) position by pressing the electricalparking switch, depress the brake pedal more firmly than usual with the right foot.Then, press the power switch.
Refer to “Starting and stopping the Plug-
in Hybrid EV System” on page 7-13.
Indication lamp, warning lamp, and information screen display list
6-482**((Instruments and controls6

ScreenCauseSolution (Reference)zDriving power is restricted by the safety
system as the Plug-in Hybrid EV System
has become too hot or too cold.z You do not have to take any actions. The
restriction on the driving power will be re-
leased when the Plug-in Hybrid EV Sys- tem returns to the normal temperature.z The vehicle had not been refueled about
15 litres or more at one time for nearly 3months.
This display may appear frequently de-
pending on the use conditions of your ve- hicle such as when fuel has been staying
in the fuel tank for a long time.z Refill the 15 litres more at one time.
This display will disappear.
If the fuel remaining display will be be- low half, you can refill the fuel more than
15 litres certainly.
z If you cannot refill the fuel due to the
large amount of remaining fuel, start the
engine and drive the vehicle enough to re- duce the fuel level to approximately half
tank.z If the vehicle had not been refuelled about
15 litres or more at one time for three
months, the engine starts automatically for the maintenance of the engine or the
fuel system components while the ready indicator is illuminated.
This display may appear frequently de-
pending on the use conditions of your ve- hicle such as when fuel has been staying
in the fuel tank for a long time.
When the engine is running, this display shows the state where the drive battery is
charged, and the battery charge mode dis-
play (
) is displayed. But the
drive battery will not be full charge.
z Refill the 15 litres more at one time. This
display and battery charge mode display will disappear, and the engine will not au- tomatically start for maintenance.
If the fuel remaining display will be be- low half, you can refill the fuel more than
15 litres certainly.
z If you cannot refill the fuel due to the
large amount of remaining fuel, start the engine and drive the vehicle enough to re-
duce the fuel level to approximately half
tank.
Indication lamp, warning lamp, and information screen display list
6-492**((Instruments and controls6

ScreenCauseSolution (Reference)zThe accelerator pedal has been depressed
when the select position is in the “N”
(NEUTRAL) position.z When you start the vehicle, be sure to
check the select position indicator and make sure the select position is in the “D”(DRIVE) or “R” (REVERSE) position.
Then, please depress the accelerator ped-
al.
Refer to “Select position indicator” on page 7-17.z The selector lever has been operated when
the select position is in “P” (PARK) posi-
tion and the brake pedal is not depressed.z Operate the selector lever while depressed
firmly on the brake pedal.
The operation status of each system is displayed on the information screen. Refer to the appropriate page for the system for further details.
ScreenSystem operation statusReferencez When charging of the drive battery is
completed.Refer to “Charging” on page 3-02.z When “NORMAL” mode of S-AWC is
selectedRefer to “S-AWC drive mode” on page 7-21.
Indication lamp, warning lamp, and information screen display list
6-502**((Instruments and controls6

ScreenSystem operation statusReferencezWhen “SNOW” mode of S-AWC is selec-
tedRefer to “S-AWC drive mode” on page 7-21.z When “LOCK” mode of S-AWC is selec-
tedRefer to “S-AWC drive mode” on page 7-21.z When the mode is changed by the ECO
mode switch.Refer to “ECO mode switch” on page 6-68.z When approaching the guidance location,
etc.Refer to “Navigation information display” onpage 6-47.z When the EV priority mode is activated.Refer to “EV switch” on page 7-25.
Indication lamp, warning lamp, and information screen display list
6-512**((Instruments and controls6

ScreenSystem operation statusReferencezWhen the battery save mode is activated.Refer to “Battery save mode” on page 7-29.zWhen the battery charge mode is activa-
ted.Refer to “Battery charge mode” on page 7-29.z When the SPORT mode is activatedRefer to “SPORT mode switch” on page
7-31.z When the reversing sensor system detects
an obstruction.Refer to “Reversing sensor system” on page7-97.z When the parking sensors detect an obsta-
cle.Refer to “Parking sensors (Front/Rear)” on
page 7-101.
Indication lamp, warning lamp, and information screen display list
6-522**((Instruments and controls6