MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

To release
Manual operation
1. Make sure that the operation mode of thepower switch is ON.
2. Press down the Electric parking brake
switch while depressing the brake pedal.
Automatic operation
When the accelerator pedal is depressed
slowly while all of the following conditions are met, the Electric parking brake is auto-
matically released.
z The Plug-in Hybrid EV System is oper-
ating.
z The select position is in the “D”
(DRIVE) or the “R” (REVERSE) posi-
tion.
z The driver’s seat belt is fastened.
When the parking brake is released, the brake
warning lamp (red) and the indication lamp on the Electric parking brake switch go off.
Before driving, be sure that the Electric park-
ing brake is released and the brake warning lamp is off.CAUT,ONz After the Electric parking brake switch has
been operated to apply or release the Electric
parking brake, if the brake warning lamp
(red) and the indicator on the Electric park- ing brake switch remain blinking or the
Electric parking brake warning lamp (yel- low) remains illuminated, the Electric park-ing brake system may be malfunctioning and
the Electric parking brake may not be ap-
plied or released. Immediately park your ve- hicle in a safe place and contact the nearest
MITSUBISHI MOTORS Authorized Serv-
ice Point.
z If a vehicle is driven without releasing the
Electric parking brake, the brake will over-
heat, resulting in ineffective braking and
possible brake failure.
z If the brake warning lamp (red) does not go
off after the parking brake has been released, the brake system may be malfunctioning.
Contact the nearest MITSUBISHI MOTORS
Authorized Service Point.CAUT,ONz If the acceleration of the vehicle seems ab-
normally slow after the vehicle has been parked with the Electric parking brake ap-
plied in cold weather, stop the vehicle in a
safe place, then apply and release the Elec- tric parking brake. If the vehicle acceleration is still slow, contact the nearest
MITSUBISHI MOTORS Authorized Serv-
ice Point.NOTEz When the operation mode of the power
switch is other than ON, the parking brake
cannot be released.
z If the Electric parking brake does not auto-
matically release, it may be released by man-ual operation.
z When the select position is other than the
“P” (PARK) position, if you try to release
the Electric parking brake without depress- ing the brake pedal, the warning display will
appear.
Parking brake
7-052**((Starting and driving7

NOTEzIf you start driving without releasing the
Electric parking brake, the warning display
will appear.
z If the driver’s foot contacts the accelerator
pedal in the condition that the Electric park-
ing brake can be released by an automatic
operation, the Electric parking brake may be released automatically.
Warning display
Warning lamp (yellow)
Warning display
If there is a malfunction in the system, the
warning lamp will come on. In addition, thewarning display appears on the information
screen in the multi information display.
Under normal conditions, the warning lamp
only comes on when the operation mode is put in ON and goes off a few seconds later.CAUT,ONz When the Electric parking brake warning
lamp (yellow) does not illuminate or remains
illuminated when the operation mode of the
power switch is put in ON, or comes on
while driving, the Electric parking brake may not be applied or released. Immediatelycontact the nearest MITSUBISHI MOTORS
Authorized Service Point. For details, refer
to “Electric parking brake warning lamp (yellow)” on page 6-56.
When parking your vehicle while the Elec-
tric parking brake warning lamp (yellow) is illuminated, park the vehicle on level and stable ground, put the select position to “P”
(PARK) and place chocks, blocks, or stones behind and in front of the tyres to prevent
the vehicle from moving.Parking
E00600602818
To park the vehicle, firmly apply the parkingbrake, and then press the electrical parkingswitch to lock the wheels.
Parking on a hill
To prevent the vehicle from rolling, follow
these procedures:
Parking on a downhill slope
Turn the front wheels towards the kerb and
move the vehicle forward until the kerb side wheel gently touches the kerb.
Apply the parking brake and press the electri-
cal parking switch.
If necessary, apply chocks to wheels.
Parking on an uphill slope
Turn the front wheels away from the kerb and
move the vehicle back until the kerb side wheel gently touches the kerb.
Apply the parking brake and press the electri-
cal parking switch.
If necessary, apply chocks to wheels.
Parking with the engine run-ning
Never leave the engine running while you
take a short sleep/rest. Also, never leave the engine running in a closed or poorly ventila-
ted place.
Parking
7-062**((Starting and driving7

:ARN,NGzLeaving the engine running risks injury
or death from accidentally moving the se-
lector lever or the accumulation of toxic
exhaust fumes on the passenger compart- ment.
Where you park
:ARN,NGz Do not park your vehicle in areas where
combustible materials such as dry grass
or leaves can come in contact with a hot exhaust, since a fire could occur.
When leaving the vehicle
Always carry the key and lock all doors and
the tailgate when leaving the vehicle unatten- ded.
Always try to park your vehicle in a well lit
area.
CAUT,ONz When you leave the vehicle, be sure that you
have stopped the Plug-in Hybrid EV System.
The engine may start suddenly by a remain- ing amount decline of the drive battery.Steering wheel height and
reach adjustment E00600701652
1. Release the lever while holding the
steering wheel up.
2. Adjust the steering wheel to the desired
position.
3. Securely lock the steering wheel by pull-
ing the lever fully upward.
A- Locked B- Release
:ARN,NGz Do not attempt to adjust the steering
wheel while you are driving the vehicle.Inside rear-view mirror
E00600802315
Adjust the rear-view mirror only after making
any seat adjustments so you have a clear
view to the rear of the vehicle.
Type 1Type 2
:ARN,NGz Do not attempt to adjust the rear-view
mirror while driving. This can be danger-
ous.
Always adjust the mirror before driving.
Adjust the rear-view mirror to maximize the
view through the rear window.
Steering wheel height and reach adjustment
7-072**((Starting and driving7

To adjust the vertical mirrorposition
It is possible to move the mirror up and down to adjust its position.
To adjust the mirror position
It is possible to move the mirror up/down and left/right to adjust its position.
To reduce the glare
Type 1
The lever (A) at the bottom of the mirror can
be used to adjust the mirror to reduce the
glare from the headlamps of vehicles behind you during night driving.
1- Normal
2- Anti-glare
Type 2
When the headlamps of the vehicles behind you are very bright, the reflection factor ofthe rear-view mirror is automatically changed
to reduce the glare.
When the operation mode of the power
switch is put in ON, the reflection factor of the mirror is automatically changed.
NOTEz Do not hang items on, or spray glass cleaner
on the sensor (1), as reduced sensitivitycould result.
Inside rear-view mirror
7-082**((Starting and driving7

Outside rear-view mirrorsE00600900628To adjust the mirror position
E00601001737
The outside rear-view mirrors can be operat-
ed when the operation mode is put in ON or ACC.
:ARN,NGz Do not attempt to adjust the rear-view
mirrors while driving. This can be dan- gerous.
Always adjust the mirrors before driving.
z Your vehicle is equipped with convex type
mirrors.
Please take into consideration, that ob- jects you see in the mirror will look small- er and farther away compared to a nor-
mal flat mirror.
Do not use this mirror to estimate dis- tance of following vehicles when changing lanes.
1. Place the lever (A) to the same side as
the mirror whose adjustment is desired.
L- Left outside mirror adjustment
R- Right outside mirror adjustment
2. Press the switch (B) to the left, right, up
or down to adjust the mirror position. 1- Up
2- Down
3- Right
4- Left
3. Return the lever (A) back to the middle
position (

CAUT,ONzIt is possible to retract and extend the mir-
rors by hand. After retracting a mirror using
the mirror retractor switch, however, you
should extend it by using the switch again, not by hand. If you extended the mirror by
hand after retracting it using the switch, it
would not properly lock in position. As a re- sult, the mirror could move because of thewind or vibration while you are driving, and
this may limit the driver’s rearward visibili- ty.NOTEz Be careful not to get your hands trapped
while a mirror is moving.
z If you move a mirror by hand or it moves af-
ter hitting a person or object, you may not be
able to return it to its original position using the mirror retractor switch. If this happens,
push the mirror retractor switch to place the mirror in its retracted position and then push
the switch again to return the mirror to its original position.
z When freezing has occurred and mirrors fail
to operate as intended, please refrain from repeated pushing of the retractor switch as
this action can result in burn-out of the mir-
ror motor circuits.Retracting and extending the
mirrors without using the mir- ror retractor switch
The mirrors automatically retract or extend
when the doors and tailgate are locked or un-
locked using the remote control switches or
the keyless operation function of the keyless
operation system.
Refer to “Keyless operation system: To oper- ate using the key-less operation function,
Keyless entry system” on pages 4-09 and
4-03.
NOTEz Functions can be modified as stated below.
Please consult a MITSUBISHI MOTORS
Authorized Service Point.
On vehicles equipped with the Smartphone
Link Display Audio or the MITSUBISHI
Multi-Communication System (MMCS), screen operations can be used to make theadjustment. Refer to the separate owner’smanual for details.

NOTEzThe heated mirror can be set so that it can
turn on automatically only once if the ambi-
ent temperature becomes low, when the op- eration mode is put in ON.
For further information, we recommend you to consult a MITSUBISHI MOTORS Au-
thorized Service Point. On vehicles equipped
with the Smartphone Link Display Audio or the MITSUBISHI Multi-Communication
System (MMCS), screen operations can be
used to make the adjustment. Refer to the
separate owner’s manual for details.Power switch
E00631801617
In order to prevent theft, the Plug-in HybridEV System will not start unless a preregis-tered keyless operation key is used. (Immo-
bilizer function)
If you are carrying the keyless operation key,
you can start the Plug-in Hybrid EV System.CAUT,ONz The indication lamp (A) will flash orange
when there is a problem or malfunction inthe keyless operation system. Never drive if
the indication lamp on the power switch is flashing orange. Immediately contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
z If the power switch operation is not smooth
and feels like it is sticking, do not operate the switch. Immediately contact a
MITSUBISHI MOTORS Authorized Serv-
ice Point.NOTEz When operating the power switch, press the
switch all the way in. If the switch is not
fully pressed, the Plug-in Hybrid EV System
may not start or the operation mode may not change. If the power switch is pressed cor-rectly, there is no need to hold the power
switch down.
z When the battery in the keyless operation
key has worn out, or the keyless operationkey is out of the vehicle, a warning displaywill appear.
Operation mode of the power
switch and its function
OFF
The indication lamp on the power switch
turns off.
The operation mode cannot be put in OFF unless the electrical parking switch is press-
ed.
Power switch
7-112**((Starting and driving7 A

ACC
Electrical devices such as the audio and ac-
cessory socket can be operated. Can be used when the Ready indicator is off.
The indication lamp on the power switch illu- minates orange.
ON
All vehicle’s electrical devices can be operat-
ed.
The indication lamp on the power switch illu- minates blue. The indication lamp goes off
when the Plug-in Hybrid EV System is oper- ating.
NOTEz Your vehicle is equipped with an electronic
immobilizer.
To start the Plug-in Hybrid EV System, the ID code which the transponder inside the
key sends, must match the one registered in the immobilizer computer. Refer to “Elec-
tronic immobilizer (Anti-theft starting sys- tem)” on page 4-03.Changing the operation mode
E00631901559
If you press the power switch without de-
pressing the brake pedal, you can change the
operation mode in the order of OFF, ACC,
ON, OFF.
CAUT,ONz When the Plug-in Hybrid EV System is not
operating, put the operation mode in OFF.
Leaving the operation mode in ON or ACC for a long time when the Plug-in Hybrid EV
System is not operating may cause the auxil- iary battery to discharge, making it impossi-
ble to start the Plug-in Hybrid EV System.CAUT,ONz When the auxiliary battery is disconnected,
the current operation mode is memorized. After reconnecting the auxiliary battery, thememorized mode is selected automatically.
Before disconnecting the auxiliary battery
for repair or replacement, make sure to put the operation mode in OFF.
Be careful if you are not sure which opera-
tion mode the vehicle is in when the auxili-
ary battery is run down.
z The operation mode cannot be changed from
OFF to ACC or ON if the keyless operation
key is not detected to be in the vehicle. Refer
to “Keyless operation system: Operating
range for starting the Plug-in Hybrid EV System and changing the operation mode”on page 4-08.NOTEz If the operation mode cannot be changed to
OFF, perform the following procedure.
1
. Press the electrical parking switch
and lock the wheels, then change theoperation mode to OFF.
2 . One of the other causes could be low
auxiliary battery voltage. If this oc- curs, the keyless entry system andkeyless operation will also not oper-
ate.
Contact a MITSUBISHI MOTORS Author-
ized Service Point.
Power switch
7-122**((Starting and driving7

ACC power auto-cutout func-tion
E00632801265
After approximately 30 minutes have elapsed
with the operation mode in ACC, the func-
tion automatically cuts out the power for the audio system and other electric devices that
can be operated with that position.
When the power switch operates again, the
power is supplied again.
NOTEz It is possible to modify functions as follows:

5.When you press the power switch while
depressing the brake pedal, the READY indicator in the meter blinks and the acti-
vation of Plug-in Hybrid EV System
starts.
6. When the READY indicator changes
from blinking to staying on, the startup
of Plug-in Hybrid EV System is activa- ted and the vehicle is now ready to drive.CAUT,ONz Do not press the power switch while holding
the select lever at the operated position.NOTEz Continue to depress the brake pedal until the
READY indicator in the meter stays on.
z After the Plug-in Hybrid EV System has not
started for a while, the brake pedal effort needed to start the Plug-in Hybrid EV Sys-tem may become greater.
If this occurs, depress the brake pedal more
than usual.
z You can drive your vehicle even if the en-
gine is stopped.
z The Plug-in Hybrid EV System can be star-
ted in any operation mode.
z If the READY indicator does not come on,
check the select position indicator. If the in-dicator does not indicate “P”, press the elec-
trical parking switch to display “P” position.NOTEz If the READY indicator does not come on,
turn the power switch to OFF once and, aftera while, press the power switch to start Plu- gin Hybrid EV System.Stopping the Plug-in Hybrid
EV System
E00620801457
1. Stop your vehicle completely.
2. Apply the parking brake firmly while
depressing the brake pedal.
3. After pressing the electrical parking
switch, press the power switch to stop the Plug-in Hybrid EV System. (Refer to“Electrical Parking switch” on page
7-18.)
:ARN,NGz Never stop the Plug-in Hybrid EV System
during running except in an emergency.
The effectiveness of the brake becomes very poor and the steering wheel becomes
very heavy, which can easily lead to an ac-
cident.NOTEz Do not operate the power switch during run-
ning except in an emergency. If you have to stop the Plug-in Hybrid EV System becauseof an emergency during operation, continue
to press the power switch for three seconds or longer or press the power switch threetimes or more quickly. The Plug-in Hybrid
EV System stops, the operation mode turns to ACC, and the selector lever position shifts
to the “P” position at very slow speed.
z If you press the power switch when the se-
lector lever position is other than the “P” po- sition while your vehicle is stopped, the se-
lector lever position automatically shifts to the “P” position, Plug-in Hybrid EV Systemstops, and the power mode turns to “OFF”.
z If the parking lock mechanism is faulty, a
warning is displayed on the information
screen in the multi-information display. When this warning is displayed, the Plug-in
Hybrid EV System cannot be stopped unless
you apply the parking brake and then press the power switch. Park on a flat place with
the parking brake securely applied. Have your vehicle inspected by a MITSUBISHI
MOTORS Authorized Service Point.
Starting and stopping the Plug-in Hybrid EV System
7-142**((Starting and driving7