MITSUBISHI OUTLANDER PHEV 2019 Owner's Manual (in English)

points indicated by arrows and pry gen-tly to remove the cover (A).
2. Remove the 3 screws (B) and remove
the lamp unit.
NOTEz When unfastening the screws of the fog
lamp, be careful not to mistakenly move thebeam position adjustment screw (C).
3. While holding down the tab (D), pull out
the socket (E).
4. Turn the bulb (F) anticlockwise to re-
move it.
5. To install the bulb, perform the removal
steps in reverse.
Replacement of lamp bulbs
11-292**((Maintenance11

Rear fog lamp (driver’s side)/Reversing lamp (Passenger’sside)
E01004101655
1. Insert a straight blade (or minus) screw-
driver with a cloth over its tip at the edge
of the lamp unit, and then push the lamp
unit upward to remove it.
2. Turn the socket (A) anticlockwise to re-
move it, and then pull the bulb out of the
socket.
3. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lamp unit, first insert the
notch (B) into the hole on the body, and then
push on the lamp unit to fit it into place.Rear combination lamps
E01004202767
1. Open the tailgate.
Replacement of lamp bulbs
11-302**((Maintenance11

2.Remove the screws (A), and then move
the lamp unit towards the rear of the ve-
hicle to unfix the notch (B) and pins (C) of the lamp unit.
3. Turn the socket anticlockwise and re-
move it, and then pull the bulb out of the
socket.
D-Rear turn-signal lampE-Tail lamp and stop lamp (LED)-cannot
be replacedNOTEz The tail lamp and stop lamp use an LED in-
stead of the bulb.
If you need to repair or replace these lamps, contact a MITSUBISHI MOTORS Author-
ized Service Point.
4. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lamp unit, align the
notch (F) and pin (G) on the lamp unit with the clip (H) and hole (I) in the body.Licence plate lamps
E01004602325
1. Remove while pressing the lamp unit
(A) to the left side of the vehicle.
2. Insert a minus screwdriver with the end
covered with a cloth or other object to press the hook (B) aside and remove the lens.
Replacement of lamp bulbs
11-312**((Maintenance11

3. Remove the bulb from the socket.
4.To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the lamp unit, first insert the
end of tab (C) and then align tab (D).
Replacement of lamp bulbs
11-322**((Maintenance11

Vehicle labeling................................................................................. 12-02
Vehicle dimensions........................................................................... 12-04
Vehicle performance......................................................................... 12-05 Vehicle weight................................................................................... 12-05
Engine specifications........................................................................ 12-06
Charging system specifications.........................................................12-07
Electric motor specifications.............................................................12-08
Low voltage electrical system........................................................... 12-08Tyres and wheels............................................................................... 12-09
Fuel consumption.............................................................................. 12-09
Capacity............................................................................................ 12-106pecifications
2**((12

Vehicle labelingE01100105571
Vehicle identification number
The vehicle identification number is stamped on the bulkhead as shown in the illustration.
Vehicle information code plate
The vehicle information code plate is riveted as shown in the illustration.
The plate shows the model code, engine
model, transaxle model and body colour
code, etc.
Please use this number when ordering re- placement parts.
1- Model code
2- Engine model code
3- Transaxle model code
4- Body colour code
5- Interior code
6- Option code
7- Exterior code
Vehicle identification number plate (RHD vehicles only)
The vehicle identification number is stamped on the plate riveted to the left front corner of
the instrument panel pad. It is visible from outside of the vehicle through the wind-
screen.
Vehicle labeling
12-022**((Specifications12

Engine model/number
The engine model and number are stamped
on the engine cylinder block as shown in the illustration.
*: Front of the vehicle
Electric motor model/number
The electric motor model and number are
stamped as shown in the illustration.
1- Front motor
2- Rear motor
*: Front of the vehicle
Vehicle labeling
12-032**((Specifications12

Vehicle dimensionsE011002051781Front track1,540 mm2Overall width1,800 mm3Front overhang990 mm4Wheel base2,670 mm5Rear overhang1,035 mm6Overall length4,695 mm7Ground clearance (un-
laden)Without exhaust pipe protector190 mm8With exhaust pipe protector185 mm9Overall height (unladen)1,710 mm10Rear track1,540 mm
Vehicle dimensions
12-042**((Specifications12

Minimum turning radiusBody5.76 mWheel5.3 m

Vehicle performanceE01100303553Maximum speed170 km/h

Vehicle weight E01100409309ItemExcept for S EditionS EditionLHDRHDLHDRHDKerb weightWithout op-tional parts1,880 kg1,900 kgWith full op- tional parts1,947 kg1,945 kg1,957 kg1,955 kgMaximum gross vehicle weight2,390 kgMaximum axle
weightFront1,200 kgRear1,255 kg, 1,365 kg *Maximum towable
weightWith brake1,500 kgWithout brake750 kgMaximum trailer-nose weight75 kg* : In case of trailer towing
Vehicle performance
12-052**((Specifications12

ItemExcept for S EditionS EditionLHDRHDLHDRHDMaximum roof load80 kgSeating capacity5 persons*: In case of trailer towingNOTEz Trailer specifications indicate the manufacturer’s recommendation.

Engine specifications
E01100604856Engine model4B12No. of cylinders4 in lineTotal displacement2,360 ccBore88.0 mmStroke97.0 mmCamshaftDouble overheadMixture preparationElectronic injectionMaximum output (EEC net)99 kW/4,500 rpmMaximum torque (EEC net)211 N