MITSUBISHI OUTLANDER PHEV 2020 Owner's Manual (in English)

4.Remove the glove box fastener (C), and
then remove the glove box.Sub fuse block
When changing the fuse of the sub fuse
block, perform it with the hole of the bottom cover.
Engine compartment
In the engine compartment, the fuse block islocated as shown in the illustration. While
pressing the tab (C), pull up the cover.
A- Main fuse block B- Sub fuse block
Fuses
11-172**(20(1Maintenance11

Fuse load capacity
The fuse capacity and the names of electricalsystems protected by the fuses are indicated
on the inside of the fuse lid (LHD vehicles), the back side of the glove box (RHD vehi-cles) and inside of the fuse block cover (in-
side of the engine compartment).
NOTEz Spare fuses are provided on the cover of
main fuse block in the engine compartment.
Always use a fuse of the same capacity for replacement.Passenger compartment fuse lo-
cation table
Fuses
11-182**(20(1Maintenance11 Main fuse blockSub fuse block
(LHD)
Sub fuse block
(RHD)

No.Sym-bolElectrical sys- temCa-
paci- ties1Electric window control30 A *12Rear window
demister30 A *13Heater30 A4Windscreen wip-
ers30 A5Door locks20 A6Rear fog lamp10 A*27Accessory sock-
et15 A8Rear windowwiper15 A9Sunroof20 A10Power switch10 A11Option10 A12Hazard warning flasher15 A*1: Fusible link
*2 : Even if your vehicle is equipped with the
rear fog lamp, the fuse of the rear fog lamp
may not be installed on your vehicle.
No.Sym- bolElectrical sys- temCa-
paci- ties134-wheel drive system10 A14Stop lamps
(Brake lamps)15 A15Instruments10 A16SRS airbag7.5 A17Radio15 A18Control unit re- lay7.5 A19Interior lamps
(Room lamps)15 A20Reversing lamps (Backup lamps)7.5 A21Heated door mirror7.5 A22Outside rear-view mirrors10 A*1 : Fusible link
*2 : Even if your vehicle is equipped with the
rear fog lamp, the fuse of the rear fog lamp
may not be installed on your vehicle.
No.Sym- bolElectrical sys- temCa-
paci- ties
23
Cigarette lighter/Accessory sock- et
15 A24
Charge7.5 AHeated steeringwheel15 A25Power seat
(Driver seat)30 A *126Heated seat30 A27Power seat (Pas-
senger seat)30 A *1*1
: Fusible link
*2 : Even if your vehicle is equipped with the
rear fog lamp, the fuse of the rear fog lamp
may not be installed on your vehicle.
z Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
z The table above shows the main equip-
ment corresponding to each fuse.
Fuses
11-192**(20(1Maintenance11

Engine compartment fuse loca-tion tableNo.Sym- bolElectrical system
Ca-
paci- tySBF1Air conditioning con- denser fan motor30
A *SBF2———SBF3———SBF4Radiator fan motor40
A *SBF5Anti-lock brake system40
A *SBF6———SBF7Anti-lock brake system30
A *BF1Electric tailgate30 ABF2Audio system amp30 ABF3IODIOD30 ABF4———F1———F2Wiper de-icer15 AF3Electric parking brake7.5 AF4Daytime running
lamps10 A*: Fusible link
No.Sym-
bolElectrical system
Ca-
paci- tyF5Front fog lamps15 AF6Heated steering wheel15 AF7Headlamp washer20 AF8Security horn20 AF9Horn10 AF10ETV15 AF11Charging lid lock15 AF12Engine7.5 AF13ENG/POWER20 AF14Fuel pump15 AF15Ignition coil10 AF16———F17Headlamp high-beam (left)10 AF18Headlamp high-beam(right)10 A*: Fusible link
Fuses
11-202**(20(1Maintenance11Main fuse block
Behind of the fuse block cover

No.Sym-bolElectrical system
Ca-
paci- ty
F19
Headlamplow beam (left)
LED20 AF20
Headlamplow beam (right)
LED20 AF21
Headlamplow beam (left)
Halogen10 AF22
Headlamplow beam (right)
Halogen10 A
F23———#1—Spare fuse10 A#2—Spare fuse15 A#3—Spare fuse20 A*: Fusible link
z Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
z The table above shows the main equip-
ment corresponding to each fuse.No.Sym- bolElectrical system
Ca-
paci- tySBF1Electrical Parking Lock30
A **
: Fusible link
No.Sym-
bolElectrical system
Ca-
paci- tySBF2Vacuum pump (Regen- erative brake)30
A *F1Water pump (Electric
motor)20 AF2Battery management unit7.5AF3Drive battery PTCheater15AF4Fuel tank filler door7.5 AF5Solenoid valve (Airconditioning)7.5 AF6Water pump (Air con- ditioning)7.5 AF7Electric motor unitcontrol10 AF8Heated windscreen7.5 A
F9
Power feeder and
charger connector (12V)
10 A
Drive battery fan mo- tor15 A*: Fusible link
Fuses
11-212**(20(1Maintenance11 Sub fuse block

No.Sym-bolElectrical system
Ca-
paci- tyF10Ignition control15 AF11Ignition control7.5 A*: Fusible link
z Some fuses may not be installed on your
vehicle, depending on the vehicle model
or specifications.
z The table above shows the main equip-
ment corresponding to each fuse.
The fuse block does not contain spare 7.5 A or 30 A fuses. If one of these fuses burns out,
substitute with the following fuse.
7.5 A: 10 A spare fuse
30 A: 30 A audio system amp fuse
When using a substitute fuse, replace with a fuse of the correct capacity as soon as possi-
ble.
Identification of fuseCapacityColour7.5 ABrown10 ARed15 ABlue20 AYellowCapacityColour30 AGreen (fuse type) / Pink (fu-
sible link type)40 AGreen (fusible link type)Fuse replacement
1.Before replacing a fuse, always turn off
the electrical circuit concerned and put
the operation mode of the power switch in OFF.
2. Remove the fuse puller (A) from the in-
side of the main fuse block cover in the
engine compartment.
3. Referring to the fuse load capacity table,
check the fuse pertaining to the problem.
B- Fuse is OK
C- Blown fuse
NOTEz If any system does not function but the fuse
corresponding to that system is normal, theremay be a fault in the system elsewhere. We
recommend you to have your vehicle checked.
Fuses
11-222**(20(1Maintenance11

4.Insert a new fuse of the same capacity
by using the fuse puller into the same
place in the fuse block.CAUT,ONz If the newly inserted fuse blows again after a
short time, we recommend you to have the electrical system checked to find the causeand rectify it.
z Never use a fuse with a larger capacity than
specified or a substitute (such as a cable or foil). Doing so could cause the circuit wires
to overheat and create a fire.Replacement of lamp bulbs
Before replacing a bulb, ensure the lamp is
off. Do not touch the glass part of the newbulb with your bare fingers; the skin oil left
on the glass will evaporate when the bulb gets hot and the vapour will condense on the
reflector and dim the surface.
CAUT,ONz Do not install commercially available LED-
type bulbs.
Commercially available LED-type bulbs
could adversely affect the operation of the
vehicle, such as by preventing the lamps and other vehicle equipment from operating
properly.
z Bulbs are extremely hot immediately after
being turned off.When replacing a bulb, wait for it to cool
sufficiently before touching it. You could otherwise be burnt.
z Handle halogen lamp bulbs with care. The
gas inside a halogen lamp bulbs is highly
pressurized, so dropping, knocking, or scratching a halogen lamp bulb can cause it
to shatter.CAUT,ONz Never hold the halogen lamp bulb with a
bare hand, dirty glove, etc.
The oil from your hand could cause the bulb to break the next time the headlamps are op-
erated.
If the glass surface is dirty, it must be cleaned with alcohol, paint thinner, etc., and
refit it after drying thoroughly.NOTEz If you are unsure of how to carry out the
work as required, we recommend you to consult a specialist.
z Be careful not to scratch the vehicle body
when removing a lamp or lens.
Replacement of lamp bulbs
11-232**(20(1Maintenance11

NOTEzWhen it rains or when the vehicle has been
washed, the inside of the lens sometimes be-
comes foggy. This is the same phenomenon as when window glass mists up on a humid
day, and does not indicate a functional prob- lem.
When the lamp is switched on, the heat will remove the fog. However, if water gathers
inside the lamp, we recommend you to have the lamp checked.Bulb location and capacityCAUT,ONz When replacing a bulb, be sure to use a new
bulb of the same type, wattage and colour. If you install a different bulb, the bulb could malfunction or fail to come on and could
lead to a vehicle fire.Outside
Type A: Halogen headlamps type
Type B: LED headlamps type 1- Front turn-signal lamps: 21 W (PY21W)2- Headlamps, high-beam Halogen: 60 W (HB3)
LED:

1- High-mounted stop lamp:

2.Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle
3. Turn the socket (C) anticlockwise to re-
move it, and then pull the bulb out of the
socket.
4. To install the bulb, perform the removal
steps in reverse.
NOTEz When installing the bulb, align the tab (D)
with the notch (E) of the socket.Headlamps (high-beam, halo-
gen bulb)
1. When replacing the bulb on the right
side of the vehicle, remove the clip (A)
holding down the washer tank spout and
then move it.
*: Front of the vehicle
2. Turn the cap (B) anticlockwise to re-
move it.
*: Front of the vehicle

Replacement of lamp bulbs
11-262**(20(1Maintenance11