NISSAN 350Z 2007 Z33 Glasses, Windows System And Mirrors Owner's Manual

POWER WINDOW SYSTEM
GW-21
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
ANTI-PINCH SYSTEM
Power window main switch and power window sub-switch monitors the power window motor operation and the
power window position (full closed or other) for driver side and passenger side power window by the signals
from encoder and limit switch in power window motor (driver side and passenger side).
When power window main switch detects interruption during the following close operation,

automatic close operation when ignition switch is in the “ON” position

automatic close operation during retained power operation

manual close operation during retained power operation
Power window main switch or power window sub-switch controls each power window motor for open and the
power window will be lowered about 150 mm (5.91 in).
POWER WINDOW CONTROL BY THE KEY CYLINDER SWITCH
When ignition key switch is OFF, power window can be opened or closed by turning the door key cylinder
UNLOCK / LOCK position more then 1.5 second over condition.

Power window can be opened as the door key cylinder is kept fully turning to the UNLOCK position.

Power window can be closed as the door key cylinder is kept fully turning to the LOCK position.
The power window operation by the key cylinder switch stops when the following operations are performed.

While performing open / close the window with power window main switch.

When the ignition switch is turned ON while the power window control operation by the key cylinder
switch.
AUTOMATIC WINDOW ADJUSTING FUNCTION
When the driver's / passenger's door(s) is opened, the window of the opened door is lowered approx. 10 mm
(0.39in).
When the door is closed, the window is raised to fully-closed positions.
Automatic window adjusting function system (opening operation) does not operate when the following.

The window is 10 mm (0.39 in) or more open from fully-closed positions.
Automatic window adjusting function system (closing operation) does not operate when the following.

The automatic window adjusting function system (opening operation) operation.

The keyless power window operation.

The power window control by the key cylinder switch operation.

GW-22
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
SchematicNIS0004N
TIWT0969E

POWER WINDOW SYSTEM
GW-23
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Wiring Diagram — WINDOW —NIS0004O
TIWT2275E

GW-24
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
TIWT1593E

POWER WINDOW SYSTEM
GW-25
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
TIWT1594E

GW-26
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
Terminal and Reference Value for BCMNIS0004P
Te r -
minalWire
colorItemSignal
input/out-
putConditionVoltage (V)
(Approx.)
11 L GIgnition switch ACC power sup-
ply (ACC or ON)InputIgnition switch
(ACC or ON position)Battery voltage
12 P Passenger side door switch InputON (open) 0
OFF (closed) Battery voltage
22 Y Power window serial link Input/Out-
put—
38 W/LIgnition switch ON power supply
(ON or START)InputIgnition switch
(ON or START position)Battery voltage
39 L CAN-HInput/Out-
put——
40 P CAN-LInput/Out-
put——
42 GY Power source (Fuse) Input — Battery voltage
52 B Ground — — 0
53 Y/B Rap signal OutputIGN SW ON Battery voltage
Within 45 second after ignition
switch is turned to OFFBattery voltage
When driver side or passenger
side door is open in power win-
dow timer operates0
54 WPower window switch power
supplyOutput — Battery voltage
55 R Power source (Fusible link) Input — Battery voltage
62 L Driver side door switch InputON (open) 0
OFF (closed) Battery voltage
PIIA2344J

POWER WINDOW SYSTEM
GW-27
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
Terminal and Reference Value for Power Window Main SwitchNIS0004Q
*: For RoadsterTe r -
minalWire
ColorItemSignal
input/outputConditionVoltage (V)
(Approx.)
1 W BAT power supply Input — Battery voltage
4* PPower window down request
signalInputWhen soft top open/close
function starts and window
down function is operating.0
Other than above 5
5 OR Encoder power supply Input — 10
6 B/R Key cylinder lock switch OutputKey position
(Neutral → Locked)5 → 0
7 SB Key cylinder unlock switch OutputKey position
(Neutral → Unlocked)5 → 0
8LDriver side
power window motor UP signalOutputWhen power window motor
UP operation.Battery voltage
9 Y Limit switch signal InputDriver side door window is
between fully-open and just
before fully-closed position
(ON).0
Driver side door window is
between just before fully-
closed position and fully-
closed position (OFF).5
10 BR Rap signal OutputIGN SW ON Battery voltage
Within 45 second after igni-
tion switch is turned to OFFBattery voltage
When driver side or passenger
side door is open in power
window timer is operates0
11 GDriver side
power window motor DOWN
signalOutputWhen power window motor
DOWN operation. Battery voltage
12 PU/W Power window serial linkInput/Out-
put—
13 GY Encoder pulse signalInput/Out-
putWhen power window motor
operates.
14 LGLimit switch and encoder
ground—— 0
15 B Ground — — 0
PIIA2344J
OCC3383D

GW-28
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
Terminal and Reference Value for Power Window Sub-SwitchNIS0004R
*: For RoadsterTe r -
minalWire
ColorItemSignal
input/out-
putConditionVoltage (V)
(Approx)
3 GY Limit switch and encoder ground — — 0
4 R Encoder power supply Input — 10
8LPassenger side
power window motor UP signalOutputWhen power window motor
UP operation. Battery voltage
9GPassenger side
power window motor DOWN sig-
nalOutputWhen power window motor
DOWN operation. Battery voltage
10 W BAT power supply Input — Battery voltage
11 B Ground — — 0
12 PU Encoder pulse signalInput/Out-
putWhen power window motor
operates.
13* PPower window down request sig-
nalInputWhen soft top open/close
function starts and window
down function is operating. 0
Except the above 5
15 BR Limit switch signal InputPassenger side door win-
dow is between fully-open
and just before fully-closed
position (ON).0
Passenger side door win-
dow is between just before
fully-closed position and
fully-closed position (OFF).5
16 SB Power window serial linkInput/Out-
put—
OCC3383D
PIIA2344J

POWER WINDOW SYSTEM
GW-29
C
D
E
F
G
H
J
K
L
MA
B
GW
Revision: 2006 November2007 350Z
CONSULT-III Function (BCM)NIS0004S
CONSULT-III can display each diagnostic item using the diagnostic test modes shown following.
WORK SUPPORT
DATE MONITOR
ACTIVE TEST
BCM diagnostic test itemCheck item diagnostic
test modeContent
RETAINED PWRWork support Changes setting of each function.
Data monitor Displays the input data of BCM in real time.
Active test Gives a drive signal to a load to check the operation.
Work item Description
RETAINED PWRRap signal’s power supply period can be changed by mode setting. Selects rap signal’s power
supply period between three steps

MODE 1 (45 sec.) / MODE 2 (OFF) / MODE 3 (2 min.).
Monitor item Description
IGN ON SW Indicates [ON/OFF] condition of ignition switch.
DOOR SW–DR Indicates [ON/OFF] condition of driver side door switch.
DOOR SW–AS Indicates [ON/OFF] condition of passenger side door switch.
Test item Description
RETAINED PWRThis test is able to supply RAP signal (power) from BCM (body control module) to power window
system and power sunroof system (if equipped). Those systems can be operated when turning on
“RETAINED PWR” on CONSULT-III screen even if the ignition switch is turned OFF.
NOTE:
During this test, CONSULT-III can be operated with ignition switch in “OFF” position. “RETAINED
PWR” should be turned “ON” or “OFF” on CONSULT-III screen when ignition switch is ON. Then
turn ignition switch OFF to check retained power operation. CONSULT-III might be stuck if
“RETAINED PWR” is turned to “ON” or “OFF” on CONSULT-III screen when ignition switch is OFF
position.

GW-30
POWER WINDOW SYSTEM
Revision: 2006 November2007 350Z
Work FlowNIS0004T
1. Check the symptom and customer's requests.
2. Understand the outline of system. Refer to GW-19, "
System Description" .
3. According to the trouble diagnosis chart, repair or replace the cause of the malfunction. Refer to GW-30,
"Trouble Diagnoses Symptom Chart" .
4. Does power window system operate normally? If Yes, GO TO 5, If No, GO TO 3.
5. INSPECTION END
Trouble Diagnoses Symptom ChartNIS0004U

Make sure that other systems using the signal of the following check systems operate normally.
Symptom Diagnoses / service procedureReference
page
None of the power windows can be operated using any
switch.1. Check BCM power supply and ground circuitGW-32
2. Check power window main switch power supply and
ground circuitGW-46
3. Check power window serial linkGW-44
4. Replace BCM.BCS-17
Driver side power window cannot be operated1.Check driver side power window motor circuitGW-332. Replace the power window main switch.GW-46
Passenger side power window cannot be operated.1. Check power window sub-switch power supply and
ground circuitGW-472. Check power window serial linkGW-44
3. Check passenger side power window motor circuitGW-33
4. Replace BCM.BCS-17
Anti-pinch system does not operate normally (driver
side).1. Door window sliding part malfunction

A foreign material adheres to window glass or grass
run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.—
2. Limit switch adjustingGW-52
3. Check limit switch circuit (driver side)GW-34
4. Check encoder circuit (driver side)GW-37
Anti-pinch system does not operate normally (passenger
side).1. Door window sliding part malfunction

A foreign material adheres to window glass or grass
run rubber.

Glass run rubber wear or deformation.

Sash is tilted too much, or not enough.—
2. Limit switch adjustingGW-52
3. Check limit switch circuit (passenger side)GW-36
4. Check encoder circuit (passenger side)GW-39
Power window retained power operation does not oper-
ate properly.1. Check the retained power operation mode setting.GW-292. Check door switchGW-42
3. Replace BCM.BCS-17