tow NISSAN FRONTIER 2008 D22 / 1.G Quick Reference Guide

REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
LOCK DOORS
Press the
button to lock all doors.
UNLOCK DOORS
Press the
button once to unlock the driver’s door
only. Press thebutton againwithin 5seconds to
unlock all doors.
USING THE PANIC ALARM
Press andhold the
button forlonger than0.5seconds. Thepanic alarmwill
sound and the headlights will stay on for 25 seconds. The panic alarm stops when it
has run for 25 seconds or when any button is pressed on the keyfob.
SILENCING THE HORN BEEP FEATURE
 To deactivate: Press and hold theandbuttons for at least 2 seconds.
 To activate: Press and hold the
andbuttons for at least 2 seconds.
WINDSHIELD WIPER/WASHER SWITCH
The ignition switchmustbeinthe ON position to
activate the windshield wipers.
 Move thelever tothe following positions tooperate
the windshield wipers:
Intermittent (INT)–Front wipers operate inter-
mittently and can be further adjusted by twisting
the time control ring
.
Low Speed (LO)– Continuous low-speed operation of front wipers.
High Speed (HI)– Continuous high-speed operation of front wipers.
Mist (MIST) – Lift the lever up for one sweep of the front wipers.
 Pull the lever toward you to activate front washer fluid and several sweeps of the wipers.
2

MOONROOF CONTROLS (if so equipped)
The ignition switch must be in the ON position to operate the
moonroof controls.
TILTING THE MOONROOF
 To tiltthe moonroof up,first close themoonroof by
pushing theswitch toward UP/CLOSE
.Release
the switch, then push the UP/CLOSEswitch again to tilt
the moonroof up.
 To tiltthe moonroof down,pushtheswitch toward
DOWN/OPEN
.
SLIDING THE MOONROOF
 To fully open the moonroof, push the switch toward DOWN/OPEN. To open the
moonroof part way, push the switch in any direction while the moonroof is sliding to stop
it in the desired position.
 To fully close themoonroof, pushtheswitch toward UP/CLOSE
.To close the
moonroof part way, push the switch in any direction while the moonroof is sliding to stop
it in the desired position.
FRONT SEAT ADJUSTMENTS
With manual seats (if so equipped):
 Pull uponthe lever under thefront ofthe
seat and slide backward or forward; release.
 Lift the lever
on the side of the seat to
adjust yourseatback forwardorbackward;
release when you have found a comfortable
angle and the seat belt fits properly.
 Turn either dial
to adjust the angle and
height of the seat cushion to the desired position.
With power seats (if so equipped):
 Move the control
forward or backward to adjust the seat
cushion forward or backward.
 Pull uponthe control
toraise theseat cushion; push
down to lower the cushion.
 Push the switch
forward to move the seatback forward;
push it back to move the seatback backward.
Lumbar Support (if so equipped)
Your driver’s seathasalumbar support; adjustitby moving the
lever
up or down.
12

FOLD FLAT FRONT PASSENGER SEAT (if so equipped)
Tofold thefront passenger’s seatbackflatfor
extra storage lengthwhentransporting long
items:
 Slide theseat tothe rearmost position.Lift
up on the recline lever
, located on the
outside edge of the seat, and fold the seat-
back forward as far as it will go.
 Lift up on the latch
located on the upper corner of the seatback to release the back
of the seat.
 Once the seatback is released, it will enable you to fold the front passenger seatback flat
over the seat cushion.
FOLDING THE REAR BENCH SEAT (Crew Cab Model only)
FOLDING THE SEATBACK DOWN:
To fold therear bench seatback downtoaccess the
jacking tools, pull up on the straps
located on the
outer edgeofthe seatbacks andfoldtheseatback
forward.
FOLDING THE SEAT BASE UP
To fold therear bench seatbase uptoaccess the
under-seat storage bins:
 Lift up on the lever
located on the side of the
seat, while lifting up the front of the seat cushion.
 Repeat thisprocess toraise andsecure theseat
cushion on the other side of the vehicle. Fold the
bottom of the seat cushion toward the back of the
vehicle until it locks into place.
 Repeat thisprocess toraise andsecure theseat
cushion on the other side of the vehicle.
UTILITY BED WITH SPRAY-ON BED LINER AND UTILI-TRACK™
SYSTEM (if so equipped)
The Utili-track™ channel system allows you to move
tie-down clampsinthe bed tothe best location to
secure a load.
 The tie-down cleatsmustbeinstalled sothe
clamp isproperly seatedinthe notches inthe
rail. Ifthe tie-down cleatisnot seated inthe
notches, itwill not beflush withtherailand
cannot beproperly tightened. Thebolt inthe
center of the cleat must be tightened hand-tight
(20 – 40 inch pounds) .
13