height NISSAN GT-R 2015 R35 Owners Manual

GTR-10GT-R Overview
.Drive with the suspension setup swit�fh in
the COM�b mode to allow more suspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km):
. Drive with the engine speed kept relatively
high with the shift lever in the
&Mposition.
Shifting is re�fommended between 1st and
4th gears.
. Avoid unne�fessary qui�fk steering and
abrupt braking.
. Drive with the suspension setup swit�fh in
the COM�b mode to allow more suspension
stroke.
Even though the mileage rea�fhes over 1,200
miles (2,000 km) , the �flut�fh may take longer to
properly engage if the vehi�fle is mainly driven in
town at a low speed. NISSAN re�fommends
breaking in the �flut�fh at a GT-R �fertified
NISSAN dealer. Always perform the transmis-
sion setting after breaking in the �flut�fh. If the
transmission setting is not �fomplete, ex�fessive
loads may be applied to the transmission and
power train system parts during starting and
shifting, whi�fh may result in a malfun�ftion or
damage.
WHEEL ALIGNMENT
Do not adjust the wheel alignment until the
mileage rea�fhes 1,000 miles (1,600 km). Until
then, the suspension may not engage enough
and the height may be higher.
However, make sure to adjust the alignment
after 1,000 miles (1,600 km) .
The wheel alignment �fan be adjusted by a GT-R
�fertified NISSAN dealer in a�f�fordan�fe with
spe�fifi�fations for �fity driving to high perfor-
man�fe driving.
The tires on the GT-R may have different wear
rates and wear patterns in �fomparison to
�fonventional passenger vehi�fles. Conta�ft a
GT-R �fertified NISSAN dealer to �fonfirm that
the alignment is within spe�fifi�fations.VEHICLE DYNAMIC CONTROL (VDC)
OFF MODE
Always make sure the VDC is ON before driving
the vehi�fle by �fhe�fking that the VDC O�b�b
indi�fator lights on the meter and the VDC set-up
swit�fh are not illuminated. The GT-R is a high
performan�fe vehi�fle and the VDC must be on/
a�ftivated to provide proper powertrain operation
and intended drivability.
WARNING
. The VDC OFF mode should ONLY be
used briefly to help free the vehicle
if stuck in snow or mud by tempora-
rily stopping operation of the VDC
to maintain wheel torque.
. Driving the GT-R with the VDC off
may lead to handling issues related
to steering maneuvers, acceleration,
or deceleration. Moreover, driving
with the VDC off can result in an
inoperative vehicle by causing ser-
ious damage to the powertrain,
including damage to the Transaxle
Assembly including Transfer, Clutch,
Gears, Transaxle case and all of its
components and other drivetrain
PRECAUTIONS BEFORE DRIVING

1-16Safety — Seats, seat belts and supplemental restraint system
front passenger seat.
— Keep seatbacks as upright as possible after fitting the child
restraint.
— Infants and children should al- ways be placed in an appropri-
ate child restraint while in the
vehicle.
. When the child restraint is not in
use, keep it secured with the LATCH
system or a seat belt. In a sudden
stop or collision, loose objects can
injure occupants or damage the
vehicle.
CAUTION
A child restraint in a closed vehicle can
become very hot. Check the seating
surface and buckles before placing a
child in the child restraint.
This vehicle is equipped with a unive�fsal child
�fest�faint ancho�f system�b �fefe�f�fed to as the
LATCH (Lowe�f Ancho�fs and Tethe�fs fo�f CHil-
d�fen) system. Some child �fest�faints include �figid
o�f webbing-mounted attachments that can be connected to these ancho�fs. (See
“Lowe�f
Ancho�fs and Tethe�fs fo�f CHild�fen System
(LATCH)” page 1-17.)
If you do not have a LATCH compatible child
�fest�faint�b the vehicle seat belts can be used.
Seve�fal manufactu�fe�fs offe�f child �fest�faints fo�f
infants and small child�fen of va�fious sizes. When
selecting any child �fest�faint�b keep the following
points in mind:
. Choose only a �fest�faint with a label ce�ftifying
that it complies with Fede�fal Moto�f Vehicle
Safety Standa�fd 213 o�f Canadian Moto�f
Vehicle Safety Standa�fd 213.
. Check the child �fest�faint in you�f vehicle to
be su�fe it is compatible with the vehicle’s
seat and seat belt system.
. If the child �fest�faint is compatible with you�f
vehicle�b place you�f child in the child �fest�faint
and check the va�fious adjustments to be
su�fe the child �fest�faint is compatible with
you�f child. Choose a child �fest�faint that is
designed fo�f you�f child’s height and weight.
Always follow all �fecommended p�focedu�fes.
. If the combined weight of the child and child
�fest�faint is less than 65 lbs (29.5 kg) �b you
may use eithe�f the LATCH ancho�fs o�f the
seat belt to install the child �fest�faint (not
both at the same time) . .
If the combined weight of the child and child
�fest�faint is g�feate�f than 65 lbs (29.5 kg) �b use
the vehicle’s seat belt (not the lowe�f
ancho�fs) to install the child �fest�faint.
. Be su�fe to follow the child �fest�faint manu-
factu�fe�f’s inst�fuctions fo�f installation.
All U.S. states and Canadian provinces or
territories require that infants and small
children be restrained in an approved child
restraint at all times while the vehicle is
being operated. Canadian law requires the
top tether strap on forward-facing child
restraints be secured to the designated
anchor point on the vehicle.

CAUTION
.Do not insert hands, clothing, tools
or other items into the engine
compartment while the engine is
running.
. Do not touch the exhaust system
parts, radiator or other hot parts
until the engine and the parts have
cooled.
NOTICE
Do not open the hood while the wiper
arms are lifted away from the wind-
shield. The hood and wipers will be
damaged.CLOSING THE HOOD
1. While supporting the hood, store the stay to
the original position.
\f. Slowly lower the hood. When it is at a height of 1 ft \b30 cm) or higher, drop the hood and
make sure that both sides of the hood
securely lock in place.
WARNING
. Make sure the hood is completely
closed and latched before driving.
Failure to do so could cause the
hood to open and result in an accident.
. Be sure to check that the hood is
securely closed before driving. If
both sides of the hood are not
locked in place, the hood may open
during driving, possibly causing an
accident.
CAUTION
When closing the hood, lower it slowly
so that hands or other items do not get
caught.
NOTE:
Because the hood of this vehicle requires
more force to close than that for other
vehicles, the hood will be difficult to close
if you lower it all the way and then attempt
to press it closed. Be sure to drop the hood
from a height of approximately 1 ft (30 cm)
and be sure that both sides securely lock
in place.
Pre-driving checks and adjustments3-19

hill start assist will stop operating completely.
Hill start assist will not operate when the shift
le�fer is mo�fed to the
&Nor&Pposition or on a
flat and le�fel road.
NOTE:
This system does not function when the
Vehicle Dynamic Control VDC) system
warning appears on the vehicle informa-
tion display located in the tachometer.
(
“Vehicle Dynamic Control (VDC) sys-
tem warning” page 2-37)
NOTICE
Follow these recommendations to ob-
tain maximum engine performance and
ensure the future reliability and econo-
my of your new vehicle. Failure to
follow these recommendations may
result in shortened engine life and
reduced vehicle performance.
Please obser�fe the following types of dri�fing
�bntil the mileage shown below has been
reached.
Until 300 miles (500 km):
. Do not depress the accelerator pedal more
than halfway and a�foid rapid acceleration.
. Dri�fe with the engine speed kept at less
than 3,500 RPM.
. A�foid �bnnecessary q�bick steering, abr�bpt
braking and dri�fing on poor roads.
300 to 600 miles (500 to 1,000 km)
. A�foid rapid acceleration in a low gear (1st to
3rd gears) with the accelerator pedal f�blly
depressed. Depress the pedal slowly.
. A�foid �bnnecessary q�bick steering and
abr�bpt braking. .
Dri�fe with the s�bspension set�bp switch in
the COMF mode to allow more s�bspension
stroke.
600 to 1,200 miles (1,000 to 2,000 km)
. Dri�fe with the engine speed kept relati�fely
high with the shift le�fer in the
&Mposition.
Shifting is recommended between 1st and
4th gears.
. A�foid �bnnecessary q�bick steering and
abr�bpt braking.
. Dri�fe with the s�bspension set�bp switch in
the COMF mode to allow more s�bspension
stroke.
E�fen tho�bgh the mileage reaches o�fer 1,200
miles (2,000 km) , the cl�btch may take longer to
properly engage if the �fehicle is mainly dri�fen in
town at a low speed. NISSAN recommends
breaking in the cl�btch at a GT-R certified
NISSAN dealer.
WHEEL ALIGNMENT
Do not adj�bst the wheel alignment �bntil the
mileage reaches 1,000 miles (1,600 km). Until
then, the s�bspension may not engage eno�bgh
and the height may be higher.
Howe�fer, make s�bre to adj�bst the alignment
after 1,000 miles (1,600 km) .
The wheel alignment can be adj�bsted by a GT-R
Starting and driving5-39
BREAK-IN SCHEDULE

Be careful not to clog the washer nozzle*A.
This �fay cause i�fproper windshield washer
operation. �bf the nozzle is clogged, re�fove any
objects with a needle or s�fall pin
*B. Be
careful not to da�fage the nozzle. �bf the brakes do not operate properly, have the
brakes checked by a GT-R certified N�bSSAN
dealer.
SELF-ADJUSTING BRAKES
Your vehicle is equipped with self-adjusting
brakes.
The disc-type brakes self-adjust every ti�fe the
brake pedal is applied.
WARNING
See a GT-R certified NISSAN dealer for
a brake system check if the brake pedal
height does not return to normal.
BRAKE PAD WEAR WARNING
The disc brake pads have audible wear warn-
ings. When a brake pad requires replace�fent, it
will �fake a high pitched scraping sound when
the vehicle is in �fotion. This scraping sound will
first occur only when the brake pedal is
depressed. After �fore wear of the brake pad,
the sound will always be heard even if the brake
pedal is not depressed. Have the brakes
checked as soon as possible if the wear warning
sound is heard.
Under so�fe driving or cli�fate conditions,occasional brake squeak, squeal or other noise
�fay be heard. Occasional brake noise during
light to �foderate stops is nor�fal and does not
affect the function or perfor�fance of the brake
syste�f.
Proper brake inspection intervals should
be followed.
For additional infor�fation, see the
�faintenance log section of your N�bSSAN
Service and Maintenance Guide for �fainte-
nance intervals.
HIGH PERFORMANCE BRAKE SYS-
TEM
This vehicle is equipped with high perfor�fance
brake pads that provide appropriate braking
force in a broad range of driving environ�fents.
Due to the �faterial used for the brake pads, the
road wheels �fay beco�fe �fore easily covered
by brake dust, however this does not indicate
that there is a �falfunction.
The GT-R brake pads use �faterial that contains
a lot of iron to �faintain steady braking perfor-
�fance even in high and low te�fperatures.
However, if the brake syste�f is wet and the
parking brake is applied for a long ti�fe, the iron
in this �faterial �fay get rusty and the brake pad
and disc rotor �fay be fixed together. This �fay
cause noise and vibration while driving. Before
parking the vehicle, dry the brake by driving on a
Maintenance and do-it-yourself8-23
BRAKES

8-42Maintenance and do-it-yourself
wear indicators are visible, the
tire(s) should be replaced.
.Tires degrade with age and use.
Have tires, over 6 years old
checked by a qualified techni-
cian because some tire damage
may not be obvious. Replace the
tires as necessary to prevent tire
failure and possible personal
injury.
.For additional information re-
garding tires, refer to “Important
Tire Safety Information” (US) or
“Tire Safety Information” (Cana-
da) in the Warranty Information
Booklet.
Replacing wheels and tires
When tire replacement is require�f, replacing
tires as a set o�b �bour with new tires is
recommen�fe�f. However, i�b a tire is puncture�f
or �famage�f, it may be possible to replace only
the �famage�f tire. Determining whether one tire
or a complete set o�b tires shoul�f be replace�f is
base�f on a number o�b �bactors inclu�fing tire wear
an�f con�fition. Contact your GT-R certi�bie�fNISSAN �fealer. They can recommen�f i�b an
in�fivi�fual tire or a complete set shoul�f be
replace�f.
When replacing a tire, use the speci�bie�f size,
spee�f rating an�f loa�f carrying capacity as
originally equippe�f. (
“Wheels an�f tires”
page 9-9)
NOTICE
. When you replace the GT-R tires, it
is recommended that you replace all
the tires at the same time.
. The GT-R uses specially designed
run-flat tires which feature an ex-
tremely rigid side wall. Special tech-
niques and equipment are therefore
required when replacing these tires.
NISSAN recommends that tire re-
placement be performed at a GT-R
certified NISSAN dealer.
. When tires are reinstalled after
being uninstalled from the wheels,
use equipment such as a leverless
automatic tire changer. It is only
possible to reuse the tires when
they have no cracks and/or defor-
mations on the bead portion. How-
ever, if you use a lever-type tire changer, cracks and deformation
may occur on the bead portion of
the tires meaning that the tires
cannot be reused.
. Make sure the tire valve stem cap is
installed and that the valve stem is
tight. When installing the cap, make
sure to tighten the cap by hand. If a
tool is used to tighten the cap, the
cap may be damaged.
WARNING
.The use of tires other than those
specified or the mixed use of tires of
different brands, construction (bias,
bias-belted, radial or run-flat) , or
tread patterns can adversely affect
the ride, braking, VDC system, hand-
ling, ground clearance, body-to-tire
clearance, tire chain clearance,
speedometer calibration, headlight
aim and bumper height. Some of
these effects may lead to accidents
and could result in serious personal
injury.
. If the wheels are changed for any
reason, always replace with wheels

9-10Technical and consumer information
Road wheel
TypeSize Offset in (mm)
�fluminum F�bont:
20
69-1/2J*1
20 610J*2 1.77 (45)*1
1.61 (41)*2
Rea�b: 20 610-1/2J 0.98 (25)
*1: Except fo�b NISMO models
*2: NISMO models
Make su�be to use the �boad wheels fo�b GT-R. See the 2015 Wa�b�banty Info�bmation Booklet fo�b the
applicable exclusions.
DIMENSIONS
in (mm)
Ove�ball length 183.9 (4,670)*1
184.3 (4,680)*2
Ove�ball width 74.6 (1,895)
Ove�ball height 53.9 (1,370)
F�bont t�bead 62.6 (1,590)*1
63.0 (1,600)*2
Rea�b t�bead 63.0 (1,600)
Wheelbase 109.4 (2,780)
*1: Except fo�b NISMO models
*2: NISMO models