weight NISSAN LATIO 2007 Service Owner's Guide

MTC-80
REFRIGERANT LINES
Revision: June 20062007 Versa
REFRIGERANT LINESPFP:92600
HFC-134a (R-134a) Service ProcedureEJS0058D
SETTING OF SERVICE TOOLS AND EQUIPMENT
Discharging Refrigerant
WAR NIN G:
Avoid breathing A/C refrigerant and oil vapor or mist. Exposure may irritate eyes, nose and throat.
Remove HFC-134a (R-134a) refrigerant from the A/C system using certified service equipment meeting
requirements of SAE J2210 HFC-134a (R-134a) recycling equipment or SAE J2201 HFC-134a (R-134a)
recovery equipment. If an accidental system discharge occurs, ventilate the work area before resum-
ing service. Additional health and safety information may be obtained from the refrigerant and oil man-
ufacturers.
Evacuating System and Charging Refrigerant
1. Shut-off valve 2. A/C service valve 3. Recovery/recycling equipment
A. Preferred (best) method
WJIA2195E
1. Shut-off valve 2. A/C service valve 3. Recovery/recycling equipment
4. Refrigerant container (HFC-134a) 5. Weight scale (J-39650) 6. Evacuating vacuum pump (J-39699)
WJIA2196E

STC-4
[EPS]
PRECAUTIONS
Revision: June 20062007 Versa
Service Notice or Precautions for EPS SystemUGS0008F
CAUTION:
Check or confirm the following item when performing the trouble diagnosis.

Check any possible causes by interviewing the symptom and it’s condition from the customer if
any malfunction, such as EPS warning lamp turns ON, occurs.

Check if air pressure and size of tires are proper, the specified part is used for the steering wheel,
and control unit is genuine part.

Check if the connection of steering column assembly and steering gear assembly is proper (there
is not looseness of mounting bolts, damage of rods, boots or sealants, and leakage of grease,
etc).

Check if the wheel alignment is adjusted properly.

Check if there is any damage or modification to suspension or body resulting in increased weight
or altered ground clearance.

Check if installation conditions of each link and suspension are proper.

Check if the battery voltage is proper

Check connection conditions of each connector are proper.

Before connecting or disconnecting the EPS control unit
harness connector, turn ignition switch “OFF” and discon-
nect battery ground cable. Because battery voltage is
applied to EPS control unit even if ignition switch is turned
“OFF”.

When connecting or disconnecting pin connectors into or
from EPS control unit, take care not to damage pin termi-
nals (bend or break).
When connecting pin connectors, make sure that there are
no bends or breaks on EPS control unit pin terminal.

Before replacing EPS control unit, perform EPS control unit
input/output signal inspection and make sure whether EPS
control unit functions properly or not. Refer to STC-11,
"EPS Control Unit Input/Output Signal Reference Values" .
SEF 2 89 H
SEF 2 91 H
SDIA1848E

WT-6
ROAD WHEEL TIRE ASSEMBLY
Revision: June 20062007 Versa
ROAD WHEEL TIRE ASSEMBLYPFP:40300
Balancing WheelsEES002D8
Adjust wheel balance using road wheel center.
CAUTION:

Be careful not to scratch the road wheel during removal.

Use clip-on type wheel balance weights only.
Wheel balance (Maximum allowable unbalance):
RotationEES002D9

Follow the maintenance schedule for tire rotation service inter-
vals. Refer to MA-7, "
PERIODIC MAINTENANCE" .

Do not include the T-type spare tire when rotating tires.
CAUTION:

When installing wheels, tighten them diagonally by divid-
ing the work two to three times in order to prevent the
wheels from developing any distortion.

Be careful not to tighten wheel nut at torque exceeding
the specification to prevent damage of disc rotor.
Maximum allowable unbalanceDynamic (At rim flange) Less than 5 g (0.18 oz) (one side)
Static (At rim flange) Less than 10 g (0.35 oz)
Wheel nut : 113 N·m (12 kg-m, 83 ft-lb)SM A82 9C