key NISSAN MAXIMA 2003 A33 / 5.G Navigation Manual

CAUTION

Close the display while driving to
prevent injury in an accident or
sudden stop.

Do not put any object on the open
display screen.

Do not allow the system to get wet.
Excessive moisture such as
spilled liquids may cause the sys-
tem to malfunction.
SETTING UP THE START-UP
SCREEN
When you turn the ignition key to ACC, the fol-
lowing warning is displayed on the screen:
Read the warning and select the
ENTER key .
INFO:

If you do not touch the
ENTER key , this
system will not proceed to the next step dis-
play .

If you do not use the navigation system,
press the OFF button for the display .
When the engine is turned off during route
calculation and then turned on, the [CON-
FIRMA TION OF DEST ./WA YPOINT] screen
will be displayed after the [SYSTEM
ST ART -UP] screen. When continuing the
previous route guidance, select the
OK
key . T o edit or delete, select the
Change
key .
CLEARING THE MEMORY
All the stored data (Address Book, Avoid Area,
Previous Dest) can be cleared.
1. Change to the current vehicle location
screen.
2. Select the
Setting key .
INV0487
HOW DO I OPERATE THE NISSAN NAVIGATION SYSTEM?
4-12

3. Select theSystem Setting key on the
[SETTINGS] screen.4. Select theClear Memory key .
5. Select the
Y es key .6. When the
Y es key is selected, the stored
data will be cleared, and the [SYSTEM SET -
TINGS] screen will appear .
ABOUT ROUTE GUIDANCE
NOTE:
The navigation system does not take
driving in “CAR POOL LANES” into con-
sideration for the guidance.
INV0259INV0268
INV0269
INV0270
HOW DO I OPERATE THE NISSAN NAVIGATION SYSTEM?
4-13

5 HOW DO I PROGRAM A DESTINATION?
Various wa ys to set the destina tion (or
wa ypoint) ..................................................... 5-2
Seven ca tegories .................................... 5-2
Setting with
Address Bookkey ......... 5-3
Setting with
Previous Dest.key ........ 5-4
Setting with
Address/Streetkey ......... 5-6
Setting with
Intersectionkey.............. 5-8
Setting with
Point of Interest (POI)key ........................................................ 5-11
Setting with
Citykey......................... 5-11
Setting with
Mapkey ....................... 5-13Having the system guide you to the
destina tions ............................................... 5-15
Making the system guide the route with
easy opera tion ...................................... 5-15
Making the system guide the route with
det ailed options .................................... 5-17
Adjusting and deleting the pre-set destina tion
(wa ypoints)................................................ 5-23
Quick stop.................................................. 5-26
Where am I? .............................................. 5-29

SETTING WITHAddress BookKEY
The Address Book will allow you to store lo-
cations in the memory . This is especially useful
for locations that you visit frequently .
Please refer to “Setting up and editing the ad-
dress book” on page 7-2.
1. Press the DEST button.
2. Select the
Address Book key on the
[DEST . SETTING] screen.The [DEST . SETTING (Address book)] screen
will be displayed.
3. Select the item key of your destination
(waypoint) on the [DEST . SETTING (Ad-
dress Book)] screen to display the [DEST .
SETTING] screen.4. T o set the destination (waypoint), select
route priorities and select
OK . Refer to
“Making the system guide the route with
detailed options” on page 5-17.
INFO:
Use the joystick or the
orkey to scroll
the display .INV0272
INV0273
INV0274
HOW DO I PROGRAM A DESTINATION?
5-3

NOTE:
Select the
Mapkey to display the map
screen of the area around the specified
destination (waypoint).
If necessary , operate the joystick to adjust
the location of the destination (waypoint).
T ouch theSet key and touch the
Destination key to confirm. The
[DEST . SETTING] screen will be displayed.
T o set the destination (waypoint), refer to
“Making the system guide the route with
detailed options” on page 5-17.
SETTING WITHPrevious Dest.
KEY
This system memorizes the last 10 destinations
previously chosen.T o set new destinations or waypoints from the
previous destinations.
1. Press the DEST button.
2. Select the
Previous Dest. key on the
[DEST . SETTING] screen.
A total of 10 destinations and locations previ-
ously set will be displayed.
INV0275INV0276
INV0277
HOW DO I PROGRAM A DESTINATION?
5-4

3. Select the item key of your destination
(waypoint) on the [DEST . SETTING (Previ-
ous Dest.)] screen to display the [DEST .
SETTING] screen.4. T o set the destination (waypoint), select
route priorities and select
OK . Refer to
“Making the system guide the route with
detailed options” on page 5-17.NOTE:
T o slightly after the destination, select
the
Mapkey to display the map screen
of the area around the specified desti-
nation (waypoint).
INV0278INV0274INV0279
HOW DO I PROGRAM A DESTINATION?
5-5

5. If necessary , operate the joystick to adjust
the location of the destination (waypoint).
T ouch the
Setting key and touch the
Destination key to confirm. The
[DEST . SETTING] screen will be displayed.
T o set the destination (waypoint), refer to
“Making the system guide the route with
detailed options” on page 5-17.
SETTING WITHAddress/Street
KEY
Sets the destination (waypoint) from the street
names and addresses that you enter .There are two search methods; direct search by
the street names, and search by the street
names after a city is defined.
1. Press the DEST button.
2. Select the
Address/Street key .
NOTE:
The location displayed using the house
number is the vicinity of the locations
corresponding to the house numbers
stored in the data. It may differ from the
actual location.3. A keyboard will be displayed on the [DEST .
SETTING (Address/Street)] screen. Enter
the street name you want to set.
INFO:
It is not possible to enter names if they are not
stored in the CD-ROM.
INV0284
INV0280
INV0281
HOW DO I PROGRAM A DESTINATION?
5-6

4. Enter the street name of your destination.
For example, enter
T , thenU.
5. Enter
U , then select theList key .
The list screen of street names which have
TU at the top will appear .
If less than 5 suggested streets remain, they
will be displayed automatically .

The city names and street names will be
displayed.

Use the joystick or the ON-SCREENor
key to scroll the display .

Select the
Previous key on the screen to
display the input screen for street names.
6. Select one street of your destination.7. Enter the house number .
Select the
Enter key to display the [DEST .
SETTING] screen.
8. T o set destination, select route priorities
and select
OK . Refer to “Making the sys-
tem guide the route with detailed options”
on page 5-17.
NOTE:
T o slightly after the destination, select
the
Mapkey to display the map of the
area around the house number .
INV0282INV0283INV0335
HOW DO I PROGRAM A DESTINATION?
5-7

An approximate location corresponding to
the entered house number is displayed. If
necessary , correct the location using the
joystick.

The location displayed by the calculation
using the house number may differ from the
actual location. In that case, correct the lo-
cation using the joystick.

Press the PUSH ENTER switch.

Select the
Dest. key .INFO:
For streets with no house numbers stored in
the data, the map of a typical location will be
displayed.
The [DEST . SETTING] screen will appear .
Please refer to “Making the system guide the
route with detailed options” on page 5-17.
INFO:
When the city name is known, the street name
can be defined quickly using theCity key .
SETTING WITHIntersectionKEY
This will allow you to set an intersection as a
destination (waypoints).
1. Press the DEST button.
2. Select the
Intersection key .
A keyboard will be displayed.
INV0285
INV0286INV0287
HOW DO I PROGRAM A DESTINATION?
5-8

3. Enter the first street name where the des-
tination (waypoint) is located using the key-
board, then select the
List key .4. Select the first street name using the same
procedures.
INFO:

For a road where lanes with different traffic
directions are shown separately , the list
shows first street name, second street
name, ...

When entering a street name, enter a minor
street name as the first street and the cal-
culation will be easier and quicker .5. Enter the 2nd (intersecting) street name,
then select the
List key .
INFO:
If there are less than 5 streets which intersect
the first street, they will be displayed automati-
cally .
INV0288INV0289INV0290
HOW DO I PROGRAM A DESTINATION?
5-9