steering wheel NISSAN MAXIMA 2016 A36 / 8.G Nissan Connect Navigation Manual


> (GLW    0RGHO 1&*1-1 @
7. Voice recognition
VOICE RECOGNITIONNCGNJN1402-120906-FAF38580-C669-4F26-B8D0-7EC58692FC6D
USING VOICE RECOGNITION SYS-
TEM
NCGNJN1402-120906-1C8F749E-4AF3-47FE-9FE0-7B0B8B8AF458
InitializationNCGNJN1402-120906-60C8EC21-9C96-4FBC-A946-5937BAB414ECWhen the ignition switch is in the ON or ACC
position, Voice Recognition is initialized. When
the initialization is complete, the system is ready
to accept voice commands. If<
>on the
steering wheel is pushed before the initialization
completes, the display will show a message to
wait until the system is ready.
BEFORE STARTINGNCGNJN1402-120906-17B90F0D-2C92-4147-8CBB-60019E6215D6To get the best recognition performance from
Voice Recognition, observe the following items.
. The interior of the vehicle should be as quiet
as possible. Close the windows to eliminate
the surrounding noises (traffic noise, vibra-
tion sounds, etc.) , which may prevent the
system from correctly recognizing the voice
commands.
. Wait until the tone sounds before speaking a
command.
. Speak in a natural conversational voice
without pausing between words. .
The system cannot recognize voice com-
mands spoken from passenger seats.
GIVING VOICE COMMANDSNCGNJN1402-120906-B79272C7-32FE-481D-B7B3-A50FF427C81A1. Push <>located on the steering wheel.
5GE0023X
2. A list of commands appears on the screen,
and the system provides the voice menu
prompt.
Available category commands are displayed
on the left side of the screen. Speak or touch
a category command from the category
command list.
INFO:
.Some of the commands for each categoryare shown on the right side of the screen
and they can also be spoken without
selecting a category.
.After executing the category command,only the commands related to the se-
lected category can be recognized.
ªCommand listº (page 7-6)
.Highlight a category listed in the left sideof the screen with the Display Comman-
der (if so equipped) to find your preferred
command.
3. After the tone sounds and the icon on the screen changes from
to, speak a
command. You can also select a command
by directly touching the screen or by tilting
<
>/<> up or down and pushing
<OK> on the steering wheel.
INFO:
The Voice Recognition system will pause its
operation when no command is given after
three prompts. To resume the operation,
push <
>on the steering wheel.
4. Continue to follow the voice menu prompts and speak the voice commands after the
tone sounds until the preferred operation is
executed.
&RQGLWLRQ
7-2


> (GLW    0RGHO 1&*1-1 @
INFO:
To cancel a voice command, push and hold
<
> on the steering wheel or <BACK>on
the control panel.
Operating tipsNCGNJN1402-120906-5EBE1C81-7EAE-4A5C-8323-F92B58DC3259. Speak a command after the tone.
. If the command is not recognized, the system
will prompt you to speak the command again.
Repeat the command in a clear voice.
. Touch [
] on the touch screen or push
<
> on the steering wheel to return to the
previous screen.
. To exit the Voice Recognition system, push
and hold <
>on the steering wheel.
. To adjust the volume of the system feedback,
push <
- >/<+ >on the steering
wheel or turn the <VOL/
>or <VO-
LUME/
> while the system is making an
announcement.
The volume setting is also available from
[Guidance Volume] in the [Settings] menu on
the Launch Bar.
ªVolume and Beeps settingsº
(page 2-19)
. When setting a destination for route gui-
dance with some search methods, such as POI, Intersection or City Center search, the
search area is automatically set to the state/
province where your vehicle is located.
Change state/province to change the search
area to another state/province if necessary.
Voice Prompt Interrupt:
In most cases, you can interrupt the voice
feedback to speak the next command by pushing
the <
>on the steering wheel. After inter-
rupting the system, wait for a tone before
speaking your command.
One Shot Call:
To use the system faster when making a call, you
may speak the second level command skipping
speaking the first level command. For example,
push <
>and say ªRedialº after the tone
without first saying ªPhoneº.
How to see voice command screenNCGNJN1402-DA7924C7-AD6F-4EBB-A519-06BD7EFD97EA1. Push <>to display the first screen of the
voice command list.
2. Speak a command or select an item on the voice command list. The Second screen is
displayed.
3. Speak a command or select an item on the voice command list. The command is exe-
cuted or the next screen for further command
is displayed.
4. Follow the prompts to complete the com- mands.
Voice command screens:
5GE0024X
First screen
*1Shows a list of available categories. Speak a
category command or touch the key of the
7. Voice recognition
&RQGLWLRQ
7-3


> (GLW    0RGHO 1&*1-1 @
7. Voice recognition
corresponding category.
*2Shows a list of available commands for the
selected category. Speak a preferred com-
mand.
*3Touch [HELP] or say ªHelpº to hear help
announcements on how to use the system.
INFO:
Push <
>to stop the help announcements.
5GE0025X
Second screen
*4Previously selected command.
*5Command list
You can speak a command from the list or
touch the corresponding key. Preferred
words can be spoken for the part of the
command enclosed in < >.
*6[Previous]/[Next]
Say as a command or touch to go to the
previous/next screen.
5GE0026X
List screen
*7Speak a number from 1 to 5 or touch an item
on the list screen to select the item.
How to speak numbersNCGNJN1402-120906-71FDCB5E-F8C6-44F6-B150-DA7EA47CDF74The Voice Recognition system requires the user
to speak numbers in a certain way when giving
voice commands.
General rule:
500, 800 and 900 can be pronounced as ªfive
hundredº, ªeight hundredº and ªnine hundredº
respectively.
For other numbers, only single digits 0 (zero) to 9
can be used. (For example, for the number ª600º, speaking ªsix zero zeroº can be recognized by
the system, but ªsix hundredº cannot.)
Example:
1-800-662-6200
ªOne eight hundred six six two six two zero zeroº
INFO:
For the best recognition, speak ªzeroº for the
number ª0º, and ªohº for the letter ªoº.
Voice command examplesNCGNJN1402-4B0CA941-EB10-42BC-9DAB-3B5E138B4ADCAs examples, some additional basic operations
that can be performed by voice commands are
described here.
Example 1 Placing call by speaking a
phone number:
1. Push <
>located on the steering wheel.
2. Wait for the indicator to change to
.
Speak ªPhoneº.
&RQGLWLRQ
7-4


> (GLW    0RGHO 1&*1-1 @
5GE0027X
3. Speak ªDial <phone number>º.
5GE0028X
4. The phone number recognized by the systemis displayed on the screen. If the number is
correct, say ªDialº.
5. The system will make a phone call to the spoken phone number.
Example 2 Setting home as a destination:
1. Push <
>located on the steering wheel.
2. Wait for the indicator change to
. Speak
ªNavigationº.
5GE0029X
3. Speak ªGo Homeº. The navigation system will set home as a destination.
INFO:
. Location of home must be registered to the
Address Book prior to using this command.
. The step of speaking ªNavigationº can be
omitted.
Example 3 Displaying folders in the USB
device:
1. Push <
>located on the steering wheel.
2. Wait for the indicator change to
. Speak
ªAudioº.
3. Speak ªUSB Show Foldersº. The folders in the connected USB device will appear on
the touch screen display.
7. Voice recognition
&RQGLWLRQ
7-5


> (GLW    0RGHO 1&*1-1 @
NISSANCONNECTSMSERVICES
(if so equipped)
GUID-C77D3493-DF41-4650-B88C-9DC569176B1D
Symptom Possible cause Possible solution
The system cannot connect to
the NissanConnect
SMServices
Data Center. A subscription for the NissanConnect
SM
Services has not been established.
Sign up for a subscription to the NissanConnect
SMServices. For details about
subscriptions, contact the NissanConnectSMServices support line at 1-855-426-
6628.
The communication line is busy. Try again after a short period of time.
The vehicle is in a location where it is
difficult to receive radio waves. When the vehicle moves to an area where radio waves can be transmitted
sufficiently, communication will be restored. When the icon on the display shows
that the vehicle is inside the communication area, the system can be used.
TCU (Telematics Control Unit) is not turned
on. If the icon does not show that the vehicle is inside the communication area despite
the fact that the vehicle is in that location, contact the NissanConnect
SMServices
support line at 1-855-426-6628.
Radio wave reception is not sufficient for
TCU (Telematics Control Unit) operation. When the vehicle moves to an area where radio waves can be transmitted
sufficiently, communication will be restored. When the icon on the display shows
that the vehicle is inside the communication area, the system can be used.
Some of the items that are
displayed on the menu screen
cannot be selected. The vehicle is being driven and some menu
items are disabled.
Stop the vehicle in a safe location and apply the parking brake before operating the
menu screen items.
Some parts of the screen are
not displayed. The vehicle is being driven and some menu
items are disabled. Operate the system after stopping the vehicle in a safe location and applying the
parking brake.
The system does not announce
information. The volume level is set to the minimum. Adjust the volume level by operating the
<VOL/
>or <VOLUME/>located
on the control panel or on the steering wheel switch while the system is announcing
information.
8. Troubleshooting guide
&RQGLWLRQ
8-17


> (GLW    0RGHO 1&*1-1 @
Start-up screen...
.................................................. 2-9
Steering wheel controls for audio ...
............... 3-11
Steering wheel switches ...
.................................. 2-6
Storing a location/route ...
................................. 6-49
Storing avoid area ...
.......................................... 6-50
Storing home location ...
................................... 6-49
Storing location ...
............................................... 6-49
Storing route ...
.................................................... 6-50
Subscription to
NissanConnect
SMServices ...
............................. 5-7
System settings ...
............................................... 2-18
T
Text message settings ...
................................... 4-10
Touch panel ...
...................................................... 2-11
Trademarks ...
.......................................................... 1-4
Traffic information on map ...
............................ 6-47
Traffic information setting ...
.............................. 6-48
Transferring information to/from
address book ...
................................................... 6-55
Turn list ...
.............................................................. 6-32
U
USB (Universal Serial Bus)
connection ports ...
....................................... 2-7, 3-5 USB memory device player
...
.......................... 3-22
V
Viewing SiriusXM Travel Link ...
....................... 5-19
Viewing traffic events from list ...
..................... 6-46
Viewing traffic information ...
............................ 6-46
Voice Prompt Interrupt ...
..................................... 7-3
Voice recognition ...
............................................... 7-2
Voice recognition settings ...
............................ 7-23
Volume settings ...
............................................... 2-19
Index
&RQGLWLRQ
9-3