light NISSAN PATROL 1998 Y61 / 5.G Restraint System Workshop Manual

4. Install glove box assembly. (Glove box lid is open.)
5. Close the glove box lid.
Disposal of Air Bag Module and Seat Belt Pre-
tensioner
+Before disposing of air bag module and seat belt pre-tensioner, or vehicles equipped with such systems,
deploy the systems. If such systems have already been deployed due to an accident, dispose of as indi-
cated in ``DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER'' (RS-21).
+When deploying the air bag module, always use the Special Service Tool; Deployment tool KV99106400,
KV99108200 and KV99108300.
+When deploying the air bag module and seat belt pre-tensioner, stand at least 5 m (16 ft) away from the
deployment component.
+When deploying air bag module and seat belt pre-tensioner, a fairly loud noise is made, followed by smoke
being released. The smoke is not poisonous, however, be careful not to inhale smoke since it irritates throat
and can cause choking.
+Always activate one air bag module at a time.
+Due to heat, leave air bag module unattended for more than 30 minutes after deployment. Also leave seat
belt pre-tensioner unattended for more than 10 minutes after deployment.
+Be sure to wear gloves when handling a deployed air bag module.
+Never apply water to a deployed air bag module.
+Wash your hands clean after ®nishing work.
+Do not dispose of the air bag module un-deployed.
+Place the vehicle outdoors with an open space of at least 6 m (20 ft) on all sides when deploying the air
bag module while mounted in vehicle.
+Use a voltmeter to make sure the vehicle battery is fully charged.
CHECKING DEPLOYMENT TOOL
Connecting to battery
CAUTION:
The battery must show voltage of 9.6V or more.
Remove the battery from the vehicle and place it on dry wood
blocks approximately 5 m (16 ft) away from the vehicle.
+Wait 3 minutes after the vehicle battery is disconnected before
proceeding.
+Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal.
Make sure the polarity is correct. The right side lamp in the
tool, marked ``deployment tool power'', should glow with a
green light. If the right side lamp glows red, reverse the con-
nections to the battery.
SRS456
SRS005-B
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
Installation Ð Front Passenger Air Bag Module
(Cont'd)
RS-17

Checking seat belt pre-tensioner system operation
Check seat belt pre-tensioner system operation using a bulb as
follows:
1. Connect a bulb of less than 3.4W between data link connector
terminals
V7andV11.
2. After turning ignition switch from ``OFF'' to ``ON'', the bulb oper-
ates.
3. Compare the bulb operation to the chart below.
Lighting condition of the bulb SRS condition Reference item
MRS095A
No malfunction is
detected.
No further action is neces-
sary.
Ð
MRS096A
+Seat belt pre-tensioner
circuit is opened, or
+Seat belt pre-tensioner
power supply or ground
circuit is shorted.+If CONSULT is
available, go to DIAG-
NOSTIC PROCEDURE
2 (RS-32).
+If CONSULT is not
available, repair the sys-
tem as follows.*
1. Visually check the wir-
ing harness connec-
tions.
2. Replace the harness if it
has visible damage.
3. Replace driver's and
front passenger seat
belt assemblies.
(Before disposing, they
must be deactivated.)
4. Replace diagnosis sen-
sor unit.
MRS097A
Seat belt pre-tensioner
(and air bag) is deployed.Go to COLLISION DIAG-
NOSIS (RS-45).
* Follow the procedures in numerical order when repairing malfunctioning parts. Con®rm whether malfunction is eliminated
using a bulb or CONSULT each time repair is ®nished. If malfunction is still observed, proceed to the next step. When mal-
function is eliminated, further repair work is not required.
MRS054AB
TROUBLE DIAGNOSES Ð Supplemental Restraint System (SRS)
SRS Operation Check (Cont'd)
RS-31