belt NISSAN PULSAR 2015 Service Manual


> (GLW   0RGHO &$@
GUID-9D9 20AF3-899 E-4949-B9DE-B9DA38E BCD0D
Do not attempt tostart theengine bypushing the
vehicle.
CAUTION:
. Continuously Variable Transmission (CVT)/
Manual Transmission (MT)model cannot be
started bypushing. Attempting todo somay
cause damage tothe transmission.
. Three-way catalystequipped modelshould
not bestarted bypushing. Attempting todo
so may cause damage tothe catalyst.
. Never trytostart theengine bytowing.
When theengine starts,theforward surge
could cause thevehicle tocollide withthe
towing vehicle.
GUID-6FF3 F0CC-8B6E -46AC-926D-3 EB9C863FE4D
WARNING:
. Never continue drivingifyour vehicle over-
heats. Doingsocould cause avehicle fire.
. Never openthehood ifsteam iscoming out.
. Never remove theradiator orcoolant reser-
voir capwhile theengine ishot. Ifthe
radiator orcoolant reservoir capisremoved
when theengine ishot, pressurized hot
water willspurt outand possibly cause
burning, scalding orserious injury.
. Ifsteam orcoolant iscoming fromthe
engine, standclearofthe vehicle toprevent
getting burned.
. The engine cooling fanwill start atanytime
when thecoolant temperature exceedspre-
set degrees.
. Becareful nottoallow yourhands, hair,
jewelry orclothing tocome intocontact with,
or toget caught inthe cooling fanordrive
belts.
If your vehicle isoverheating (indicatedbythe high
temperature indicator),or ifyou feel alack ofengine
power, detectunusual noise,etc.,takethefollowing
steps:
1. Safely movethevehicle offthe road away from
traffic.
2. Turn onthe hazard indicator flasherlights.
3. Apply theparking brake.
4. Continuously Variable Transmission (CVT)model:
Move theshift lever tothe ªPº (Park) position.
Manual Transmission (MT)model: Movetheshift
lever tothe ªNº (Neutral) position.
DO NOTST OP THE ENGINE . 5.
Open allthe windows.
6. Turn offthe airconditioner. Movethetemperature
control tomaximum hotand thefancontrol tohigh
speed.
7. Get outfrom thevehicle.
8. Visually inspectandlisten forsteam orcoolant
escaping fromtheradiator beforeopening the
hood. Wait until nosteam orcoolant canbeseen
before proceeding.
9. Open theengine hood.
10. Visually inspectifthe cooling fanisrunning.
11. Visually inspecttheradiator andradiator hosesfor
leakage.
If the cooling fanisnot running orthe coolant is
leaking, stoptheengine.
12. After theengine coolsdown, checkthecoolant
level inthe reservoir withtheengine running. Do
not open theradiator cap.
13. Add coolant tothe reservoir ifnecessary .
Have yourvehicle inspected/repaired ataNISSAN
dealer.
In case ofemergency
6-7
PUSH
STARTING IFYOUR VEHICLE OVERHEA TS
&RQGLWLRQ


> (GLW   0RGHO &$@
7 Appearance andcare
Cleaning exterior....
........................................................... ...........................7-2
W ashing ....
........................................................... ...................................7-2
Removing spots....
...................................................... ...........................7-2
W axing ....
................................................. ................................................ 7-2
Glass ....
....................................... ............................................................. 7-2
Underbody ....
........................................................... ...............................7-3
Wheels ....
................................................. ................................................ 7-3
Aluminum alloywheels ....
...................................................... ..............7-3
Chrome parts....
...................................................... ...............................7-3Cleaning
interior....
........................................................... ...........................7-3
Air fresheners ....
................................................................ ..................7-4
Floor mats ....
...................................................... ...................................7-4
Glass ....
...................................................... ............................................7-4
Seat belts ....
...................................................... ...................................7-4
Corrosion protection ....
................................................................ ..............7-5
Most common factorscontributing tovehicle corrosion ....
...... 7-5
Environmental factorsinfluence rateofcorrosion ....
.................. 7-5
T o protect yourvehicle fromcorrosion ....
..................................... 7-5
&RQGLWLRQ


> (GLW   0RGHO &$@
7-4
Appear anceandcare
AIR FRESHENERS
GUID-491C 1655-FB80-4 2E5-B748-615749AEB 247
Most airfresheners useasolvent thatcould affect the
vehicle interior. Ifyou use anairfreshener, takethe
following precautions:
. Hanging-type airfresheners cancause permanent
discoloration whentheycontact vehicleinterior
surfaces. Placetheairfreshener inalocation that
allows itto hang freeandnotcontact aninterior
surface.
. Liquid-type airfresheners typicallycliponthe
vents. These products cancause immediate
damage anddiscoloration whenspilled oninterior
surfaces.
Carefully readandfollow themanufacturer's instruc-
tions before usingairfresheners.
FL OOR MATS
GUID-FE B53C0F-2B1 3-4DA5-9FFC -A4B230889197
The useofgenuine NISSAN floormats (ifequipped)
can extend thelifeofyour vehicle carpetandmake it
easier toclean theinterior. Regardless ofwhat mats
are used, besure theyarefitted foryour vehicle and
are properly positioned inthe foot well toprevent
interference withpedal operation. Matsshould be
maintained withregular cleaning andreplaced ifthey
become excessively worn.
Floor matpositioning aid(driver's side)
GUID-0F 3306F1-4A E6-4165-B1 83-646B6 719990D
JV A0010X
Example (LHDmodel)
This vehicle includes frontfloormatbrackets toact as
a floor matpositioning aid.NISSAN floormats have
been specially designed foryour vehicle model.
P osition themat byplacing thefloor matbracket hook
through thefloor matgrommet holewhile centering the
mat inthe foot area.
Periodically checkthatthemats areproperly posi-
tioned.
GLASS
GUID-47B68 639-6537-4853-8BB4-A5E527CF1 D3C
Use glass cleaner toremove smokeanddust filmfrom
the glass surfaces. Itis normal forglass tobecome
coated withafilm after thevehicle isparked inthe hot
sun. Glass cleaner andasoft cloth willeasily remove
this film.
CAUTION:
When cleaning theinside ofthe windows, donot
use sharp-edged tools,abrasive cleanersor
chlorine-based disinfectantcleaners.Theycould
damage theelectrical conductors, suchasrear
window defogger elements.
SEA TBEL TS
GUID-30 F2EF69-84CD -4146-8EDF-44903B81 C08C
WARNING:
. Donot allow wetseat belts toroll upinthe
retractor.
. Never usebleach, dyeorchemical solvents
to clean theseat belts, sincethese materials
may severely weakentheseat beltwebbing.
The seat belts canbecleaned bywiping themwitha
sponge dampened inamild soap solution.
Allow thebelts todry completely inthe shade before
using them. (SeeªSeat beltsº (P.1-7) .)
&RQGLWLRQ


> (GLW   0RGHO &$@
8 Maintenance anddo-it-yourself
Maintenance requirements ....
...................................................... ..............8-2
Scheduled maintenance ....
....................................... ...........................8-2
General maintenance ....
............................................ ...........................8-2
Where togo for service ....
....................................... ...........................8-2
General maintenance ....
................................................................ ..............8-2
Explanation ofgeneral maintenance items....
................................. 8-2
Maintenance precautions....
...................................................... ..........8-4
Engine compartment checklocations ....
................................................ 8-5
MRA8DE enginemodel....
................................................. ..................8-5
MR16DD Tengine model....
...................................................... ..........8-6
HR16DE enginemodel....
................................................. ..................8-7
Engine cooling system ....
............................................ ...............................8-7
Checking enginecoolant level....
............................................ ..........8-8
Changing enginecoolant ....
...................................................... ..........8-8
Engine oil....
................................................................ ...................................8-9
Checking engineoillevel ....
...................................................... ..........8-9
Changing engineoiland oilfilter ....
................................................. .8-9
Drive belt....
....................................... .......................................................... 8-11
Spark plugs....
................................................................ ............................8-12
Iridium platinum-tipped sparkplugs (ifequipped) ....
................ 8-12
Platinum alloy-tipped sparkplugs (ifequipped) ....
.................... 8-12
Brakes ....
............................................ .......................................................... 8-12
Checking parkingbrake....
....................................... ........................8-12
Checking footbrake pedal ....
.......................................................... 8-12
Brake booster ....
................................................. ................................8-13
Brake fluid....
................................................. .............................................8-13
Clutch fluid(ifequipped) ....
....................................... ............................8-14
Continuously Variable Transmission (CVT)fluid(ifequipped) ....
.... 8-15
Air cleaner filter....
............................................ .........................................8-15Wiper
blades ....
................................................................ ........................8-15
Windshield wiperblades ....
............................................ ...............8-15
Rear window wiperblade ....
......................................................... 8-16
Window washerfluid....
........................................................... ...............8-17
Battery ............................................................... .........................................8-18
V ehicle battery ....
...................................................... ........................8-18
Remote controller battery....
.......................................................... 8-19
Intelligent Key battery ....
...................................................... ...........8-20
V ariable voltage controlsystem (ifequipped) ....
.............................. 8-21
Fuses ....
...................................................... .................................................8-21
Engine compartment ....
....................................... ............................8-21
Passenger compartment ....
................................................. ...........8-22
Lights ....
............................................ .......................................................... 8-23
Headlights ....
............................................ .........................................8-23
Exterior lights....
....................................... ......................................... 8-24
Interior light....
........................................................... ........................8-24
Light locations ....
...................................................... ........................8-25
Legal requirement toadjust headlight beam(Halogen
headlight model)....
........................................................... ...............8-29
Tires andwheels ....
...................................................... ............................8-31
Tire inflation pressure ....
...................................................... ...........8-31
T ypes oftires ....
....................................... ......................................... 8-31
Tire chains ....
............................................ .........................................8-31
Tire rotation ....
........................................................... ........................8-31
Tire wear anddamage ....
....................................... ........................8-32
Tire age ....
................................................. .........................................8-32
Changing tiresandwheels ....
............................................ ...........8-32
Wheel balance ....
................................................. ............................8-32
Spare tire....
........................................................... ............................8-32
&RQGLWLRQ


> (GLW   0RGHO &$@
Tires*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepressure withagauge oftenandalways
prior tolong distance trips.Adjust thepressure inall
tires, including thespare, tothe pressure specified.
Check carefully fordamage, cutsorexcessive wear.
Tire rotation*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
In the case thatTwo-Wheel Drive(2WD) andfront &
rear tires aresame size;Tires should berotated every
10,000 km(6,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatFour-Wheel Drive(4WD) andfront &
rear tires aresame size;Tires should berotated every
5,000 km(3,000 miles).Tires marked withdirectional
indicators canonly berotated between frontandrear.
Make surethatthedirectional indicatorspointinthe
direction ofwheel rotation afterthetire rotation is
completed.
In the case thatfront tiresaredifferent sizefrom rear
tires; Tirescannot berotated.
However, thetiming fortire rotation mayvaryaccording
to your driving habitsandtheroad surface conditions.
Tire Pressure Monitoring System(TPMS)trans-
mitter components (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Replace theTPMS transmitter grommetseal,valve
core andcap when thetires arereplaced duetowear
or age.
Wheel alignment andbalance:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
If the vehicle shouldpulltoeither sidewhile driving on
a straight andlevel road, orifyou detect uneven or
abnormal tirewear, theremaybeaneed forwheel
alignment. Ifthe steering wheelorseat vibrates at
normal highway speeds,wheelbalancing maybe needed.
Windshield:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Clean thewindshield onaregular basis.Check the
windshield atleast every sixmonths forcracks orother
damage. Repairasnecessary .
Wiper blades*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forcracks orwear ifnot functioning correctly.
Inside vehicle
GUID-55 4469D2-12 96-4F49-B7A0 -0A8847FB7455
The maintenance itemslistedhereshould bechecked
on aregular basis,suchaswhen performing periodic
maintenance, cleaningthevehicle, etc.
Accelerator pedal:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that thepedal doesnotcatch orrequire uneven effort.
K eep thefloor mats away fromthepedal.
Brake pedal*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thepedal forsmooth operation andmake sure
that itis the proper distance fromthefloor matwhen
depressed fully.Check thebrake booster function. Be
sure tokeep thefloor mats away fromthepedal.
Parking brake*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check theparking brakeoperation regularly.Check
that thelever (ifequipped) orthe pedal (ifequipped)
has theproper travel.Alsomake surethatthevehicle is
held securely onafairly steep hillwhen onlythe
parking brakeisapplied.
Seat belts:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatallparts ofthe seat beltsystem (for
example, buckles,anchors, adjusters andretractors)
operate properly andsmoothly ,and areinstalled
securely .Check thebelt webbing forcuts, fraying,
wear ordamage. Steering
wheel:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check forchanges inthe steering condition, suchas
excessive play,hard steering orstrange noises.
Warning lightsandchimes:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatallwarning lightsandchimes are
operating properly.
Windshield defogger:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thattheaircomes outofthe defogger outlets
properly andingood quantity whenoperating the
heater orair conditioner.
Windshield wiperandwasher*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthewipers andwasher operate properly
and that thewipers donot streak.
Under hoodandvehicle
GUID-E5D 10961-EA14 -4A37-B87E- 268783A0FC3 8
The maintenance itemslistedhereshould bechecked
periodically (forexample, eachtimeyoucheck the
engine oilorrefuel) .
Battery*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Except formaintenance freebattery ,check thefluid
level ineach cell.Itshould bebetween theªUPPERº
and ªLOWERº lines.Vehicles operated inhigh
temperatures orunder severe conditions require
frequent checksofthe battery fluidlevel.
Brake (andclutch) fluidlevel(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
For Manual Transmission (MT)model; makesurethat
the brake andclutch fluidlevels arebetween the
ªMAXº andªMINº linesonthe reservoirs.
Except forManual Transmission (MT)model; make
sure thatthebrake fluidlevel isbetween theªMAXº
and ªMINº linesonthe reservoir.
Maintenan ceand do-it-you rself
8-3
&RQGLWLRQ


> (GLW   0RGHO &$@
8-4
Mainten anceanddo-it-yo urself
Coolant level*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thecoolant levelwhen thecoolant iscold. Make
sure thatthecoolant levelisbetween theªMAXº and
ªMINº linesonthe reservoir.
Engine drivebelt(s)*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Make surethatdrive belt(s) is/arenotfrayed, worn,
cracked oroily .
Engine oillevel*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thelevel afterparking thevehicle (onalevel
ground) andturning offthe engine.
Fluid leaks:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check underthevehicle forfuel, oil,water orother fluid
leaks afterthevehicle hasbeen parked forawhile.
W ater dripping fromtheairconditioner afteruseis
normal. Ifyou should noticeanyleaks oriffuel fumes
are evident, checkforcause andhave itcorrected
immediately .
Windshield washerfluid*:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Check thatthere isadequate fluidinthe reservoir.
MAINTENANCE PRECAUTIONS
GUID-E46 9E0D9-6CF F-4A9B-8459-D2B589DFA455
When performing anyinspection ormaintenance work
on your vehicle, alwaystakecare toprevent serious
accidental injurytoyourself ordamage tothe vehicle.
The following aregeneral precautions whichshould be
closely observed.
WARNING:
. Park thevehicle onalevel surface, applythe
parking brakesecurely andblock thewheels
to prevent thevehicle frommoving. Move
the shift lever tothe ªPº(Park) position (CVT
model) orthe shift lever tothe ªNº(Neutral)
position (MTmodel) . .
Besure theignition switchisin the ªOFFº or
ªLOCKº position whenperforming anyparts
replacement orrepairs.
. Do not work under thehood while the
engine ishot. Always turnoffthe engine
and wait until itcools down.
. Ifyou must workwiththeengine running,
keep yourhands, clothing, hairandtools
away frommoving fans,belts andanyother
moving parts.
. Itis advisable tosecure orremove anyloose
clothing andanyjewelry, suchasrings,
watches, etc.before working onyour vehi-
cle.
. Ifyou must runtheengine inan enclosed
space suchasagarage, besure there is
proper ventilation forexhaust gasesto
escape.
. Never getunder thevehicle whileitis
supported byajack.
. Keep smoking materials, flameandsparks
away fromfuelandthebattery.
. Never connect ordisconnect eitherthe
battery orany transistorized component
connector whiletheignition switchisin the
ªONº position.
. Ongasoline enginemodels withtheMulti-
port Fuel Injection (MFI)system, thefuel
filter andfuel lines should beserviced bya
NISSAN dealerbecause thefuel lines are
under highpressure evenwhen theengine is
turned off.
. Your vehicle isequipped withanautomatic
engine cooling fan.Itmay come onatany
time without warning, evenifthe ignition switch
isin the ªOFFº position andthe
engine isnot running. To avoid injury, always
disconnect thenegative batterycablebefore
working nearthefan.
. Always weareyeprotection wheneveryou
work onyour vehicle.
. Never leavetheengine ortransmission
related component harnessconnector dis-
connected whiletheignition switchisin the
ªONº position.
. Avoid directcontact withused engine oiland
coolant. Improperly disposedengineoil,
engine coolant, and/orothervehicle fluids
can hurt theenvironment. Alwaysconform to
local regulations fordisposal ofvehicle
fluids.
This ª8.Maintenance anddo-it-yourselfº section
provides instructions regardingonlythose itemswhich
are relatively easyforanowner toperform.
Y ou should beaware thatincomplete orimproper
servicing mayresult inoperating difficulties orex-
cessive emissions, andcould affect yourwarranty
coverage. Ifin doubt aboutanyservicing, haveit
done byaNISSAN dealer.
&RQGLWLRQ


> (GLW   0RGHO &$@
GUID-66B21 62B-2CD7-470F-9DAD-BD99AF54AF2C
MRA8DE ENGINEMODEL
GUID-EF68A5 F3-BA43-45B8-853E-9 1FCC2309E B6
JVC0363X
1. Brake andclutch* fluidreservoir
Ð Right-Hand Drive(RHD) models
2. Engine oilfiller cap
3. Brake fluidreservoir
Ð Left-Hand Drive(LHD) models
4. Aircleaner
5. Battery
Ð Jump starting 6.
Window washerfluidreservoir
7. Engine drivebeltlocation
8. Engine oildipstick
9. Radiator cap
Ð Vehicle overheat
10. Engine coolant reservoir
11. Fuse/fusible linkholders
*: For Manual Transmission (MT)models
Maintenan ceand do-it-you rself
8-5
ENGINE
COMPARTMENT CHECK
LOCA TIONS
&RQGLWLRQ


> (GLW   0RGHO &$@
8-6
Mainten anceanddo-it-yo urself
MR16DD TENGINE MODEL
GUID-934 CC1DB-4294 -4799-AEA9-ED2B57AE3 33C
JVM0262X
1. Brake andclutch* fluidreservoir
2. Engine oilfiller cap
3. Radiator cap
Ð Vehicle overheat
4. Aircleaner
5. Window washerfluidreservoir
6. Engine drivebeltlocation
7. Engine oildipstick 8.
Engine coolant reservoir
9. Fuse/fusible linkholder
10. Battery
Ð Jump starting
*: For Manual Transmission (MT)model
&RQGLWLRQ


> (GLW   0RGHO &$@
HR16DE ENGINEMODEL
GUID-C9ABE EC8-90E9-4A9F-9977 -AA38DC1C1 F0A
JVC0364X
1. Brake andclutch* fluidreservoir
Ð Right-Hand Drive(RHD) models
2. Engine oilfiller cap
3. Brake andclutch* fluidreservoir
Ð Left-Hand Drive(LHD) models
4. Aircleaner
5. Battery
Ð Jump starting 6.
Window washerfluidreservoir
7. Engine drivebeltlocation
8. Engine oildipstick
9. Radiator cap
Ð Vehicle overheat
10. Engine coolant reservoir
11. Fuse/fusible linkholders
*: For Manual Transmission (MT)models
GUID-431 BB6E1-F915 -4C1F-8B9B-5A574742 5D98
WARNING:
. Never remove theradiator orcoolant reser-
voir capwhen theengine ishot. Serious
burns couldbecaused byhigh-pressure
fluid escaping fromtheradiator. Waituntil
the engine andradiator cooldown.
. Engine coolant ispoisonous andshould be
stored carefully inmarked containers outof
the reach ofchildren.
. Ifthe engine wasstopped soonwhen the
engine ishot, thecooling fanmay operate
for approximately 10minutes afterthe
engine wasstopped tocool thecomponents
in the engine compartment. Whenthecool-
ing fan isoperating, besure thathands or
other items donot getcaught init(for
MR16DDT engine).
The engine cooling systemisfilled atthe factory witha
high-quality ,year-round, anti-freezecoolantsolution.
The anti-freeze solutioncontains rustandcorrosion
inhibitors, thereforeadditional coolingsystemadditives
are not necessary .
CAUTION:
. Never useanycooling systemadditives such
as radiator sealer.Additives mayclog the
cooling systemandcause damage tothe
engine, transmission and/orcooling system.
. When adding orreplacing coolant,besure
to use only Genuine NISSANEngineCoolant
or equivalent inits quality withtheproper
mixture ratio.Examples ofthe mixture ratio
of coolant andwater areshown inthe
following table:
Maintenan ceand do-it-you rself
8-7
ENGINE
COOLING SY STEM
&RQGLWLRQ


> (GLW   0RGHO &$@
12. Start theengine.
13. Check thedrain plugforany sign ofleakage.
14. Dispose ofthe used oilinthe proper manner.
Check yourlocal regulations.
15. Check theengine oillevel according tothe proper
procedure. (SeeªChecking engineoillevelº (P.8-
9) .)
After theoperation
GUID-D31 C7ECF-FDA1 -4CF1-B6A7-3C0771BAD AF0
1. For HR16DE enginemodel,installtheengine
undercover intoposition asthe following steps.
a. Pull thecenter ofthe small plastic clipout.
b. Hold theengine undercover intoposition.
c. Insert theclip through theundercover intothe
hole inthe frame, thenpush thecenter ofthe
clip into lock theclip inplace.
d. Install theother boltsthathold theundercover
in place. Becareful nottostrip thebolts or
over-tighten them.
2. Lower thevehicle carefully tothe ground.
3. Dispose ofwaste oiland filter properly .
GUID-4B 37DD34-9 FBB-48DA-870 F-42F8858 0E4D7
SDI1881
MRA8DE andMR16DDT enginemodel
1. Alternator
2. Drive beltauto-tensioner
3. Crankshaft pulley
4. Airconditioner compressor
5. Water
pump
SDI1862
HR16DE enginemodel
1. Water pump
2. Alternator
3. Crankshaft pulley
4. Airconditioner compressor
!: Tension checking point
Be sure theignition switchisin the ªOFFº position. Visually
inspectthebelt forsigns ofunusual wear,cuts,
fraying orlooseness. Regularlycheckthecondition
and tension (forHR16DE enginemodel).If the belt is
in poor condition orloose, haveitreplaced oradjusted
by aNISSAN dealer.
Maintenance anddo-it-yours elf
8-11
DRIVE
BELT
&RQGLWLRQ