light NISSAN PULSAR 2018 Workshop Manual


> (GLW   0RGHO &$@
4-10
Heater andairconditione r,and audio system
ª
º) .
.
T o cancel theseparate temperature setting,
push theªDUAL ºbutton (theDUAL indicator
light willturn off)and thedriver's side
temperature settingwillbeapplied toboth
the driver andpassenger sides.
. Donot setthe temperature lowerthantheoutside
air temperature. Doingsomay cause thetem-
perature tonot becontrolled properly.
. Ifthe windows fogup,use dehumidified heating
instead ofthe A/C offheating.
Dehumidified defrosting/defogging:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
1. Push thefront defogger ª
º button (theª
º
indicator lightwillilluminate) .
2. Push thetemperature controlbuttons (ª
º and
ª
º) to set the desired temperature.
. To quickly remove frostfromtheoutside surfaceof
the windshield, setthe temperature controland
the fanspeed tothe maximum levels.
. After thewindshield iscleared, pushtheªAUT Oº
button again(theAUTOindicator lightwillturn
off) .
. When thefront defogger ª
º button ispushed,
the airconditioner willautomatically turnonto
defog thewindshield ifthe outside temperature is
above -28C. Ifthe airrecirculation modeisturned
on atthe time, theventilation willchange fromthe
air recirculation modetothe outside aircirculation
mode toimprove thedefogging performance.
Do not setthe temperature toolow when thefront
defogger modeison (the ª
º indicator lightis
illuminated) ,because doingsomay fogupthe
windshield.
Manual operation
GUID-729 4676B-E04 5-4948-935 6-7E8823822C9D
The manual modecanbeused tocontrol theheater
and airconditioner toyour desired settings.
T o turn offthe heater andairconditioner, pushthe
ªON´OFFº button.
Fan speed control:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Push thefanspeed control ª
º button (+ side or


> (GLW   0RGHO &$@
mind.
This refrigerant willnotharm theearth's ozone
layer. However, itmay contribute inasmall partto
global warming.
Special charging equipment andlubricant arerequired
when servicing yourvehicle's airconditioner. Using
improper refrigerants orlubricants willcause severe
damage tothe airconditioner system.(SeeªAir
conditioner systemrefrigerant andlubricantº (P.9-5) .)
A NISSAN dealerwillbeable toservice your
environmentally friendlyairconditioner system.
Air conditioner filter
GUID-598 DCD57-C7 5B-4CC2-896D-9983 08A85BC5
The airconditioner systemisequipped withanair
conditioner filterwhich collects dust.To make surethe
air conditioner heatsdefogs, andventilates efficiently,
replace thefilter inaccordance withthespecified
maintenance intervalslistedinthe separate mainte-
nance booklet. To replace thefilter, contact aNISSAN
dealer.
The filter should bereplaced ifthe airflow decreases
significantly orifwindows fogupeasily whenoperating
the heater orair conditioner.
GUID-CC FAECDB-B C93-44CD- 9D95-5827181DFAD8
AUDIO OPERATIONPRECAUTIONS
GUID-FF66 CA17-020A- 4205-81A4-D B987BF13DDD
WARNING:
Do not adjust theaudio system whiledriving so
that fullattention maybegiven tovehicle
operation.
Radio
GUID-0B 22E016-C5A2 -4BB7-945F-32ABB046 3B62
. Radio reception isaffected bystation signal
strength, distancefromradio transmitter, build-
ings, bridges, mountains andother external
influences. Intermittent changesinreception
quality normally arecaused bythese external
influences.
. Using acellular phoneinor near thevehicle may
influence radioreception quality.
Compact Disc(CD) player
GUID-98ECA5 CC-50DD-4E69-97E6-0 7A6CF8348FC
. During coldweather orrainy days, theplayer may
malfunction duetothe humidity .If this occurs,
remove theCD from CDplayer anddehumidify or
ventilate theplayer completely .
. The player mayskipwhile driving onrough roads.
. The CDplayer sometimes maynotfunction when
the passenger compartment temperatureisex-
tremely high.Lower thetemperature beforeuse.
. Donot expose theCD todirect sunlight.
. CDs thatareofpoor quality ,or are dirty,
scratched, coveredwithfingerprints, orthat have
pin holes maynotwork properly .
. The following CDsmaynotwork properly .
Ð Copy control compact discs(CCCD)
Ð Recordable compactdiscs(CD-R)
Ð Rewritable compactdiscs
(CD-RW)
SAA0480
. Donot use thefollowing CDsasthey maycause
the CD player tomalfunction.
Ð 8cm (3.1 in)discs
Ð CDs thatarenot round
Ð CDs withapaper label
Ð CDs thatarewarped, scratched orhave
unusual edges.
Ð CD lens cleaner discs
. This audio system canonly playprerecorded CDs.
It has nocapabilities torecord orburn CDs.
Heater andairconditioner ,and audio system
4-11
AUDIO
SY STEM
&RQGLWLRQ


> (GLW   0RGHO &$@
4-28
Heater andairconditione r,and audio system
. Donot expose theUSB memory todirect sunlight.
. Donot spill anyliquids onthe USB memory .
Refer tothe USB memory Owner's Manualforthe
details.
AUDIO CONTROL STEERING SWITCH(if
equipped)
GUID-53 40BAAA-8CC3 -4555-AF7F-9768B8069B2 A
JVH0868X
1. Tuning switch
2. Source selectswitch
3. Volume control switch
The audio system canbeoperated usingthecontrols
on the steering wheel.
Source selectswitch
GUID-58D EF7BE-F407 -4C23-B805-4B323BB3BC7A
Push thesource selectswitch tochange themode to
available audiosource.
T uning switch
GUID-B1 DAD262- 2878-4A9E-9 791-C65B618574D4
Memory change(radio):
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Push up/down thetuning switch
or
for less
than 1.5seconds tochange theradio frequency . Seek
tuning (radio):
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Push up/down thetuning switch
or
for more
than 1.5seconds toseek thenext orprevious radio
station.
APS (Automatic ProgramSearch)FF,APS REW
(CD) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Push up/down thetuning switch
or
for less
than 1.5seconds toreturn tothe beginning ofthe
present program orskip tothe next program. Push
several timestoskip back orskip through programs.
iPod (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
. Tilting up/down forless than 1.5seconds will
increase ordecrease thetrack number.
USB (ifequipped) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
. Tilting up/down forless than 1.5seconds will
increase ordecrease thetrack number.
. Tilting up/down formore than1.5seconds will
increase/decrease thefolder number.
V olume control switch
GUID-15 379E76-6B E7-42B2-A4 FD-2912DF4 C5182
Push +or -side ofthe volume controlswitchto
increase ordecrease thevolume.
USB/AUX CONNECT OR(models withnavi-
gation system)
GUID-339 3C35B-8B9 6-45BB-AC5 9-1087D0FD FD42
JVH0546X
The USB/AUX connectorislocated inthe center
console.
For details, seetheseparately providedNISSAN
Connect Owner'sManual.
&RQGLWLRQ


> (GLW   0RGHO &$@
5-2
Starting anddriving
GUID-41 CA11C8-A71 B-431A-9816 -BFD8BE3B85AC
During thefirst 1,600 km(1,000 miles),follow these
recommendations toobtain maximum engineperfor-
mance andensure thefuture reliability andeconomy of
your newvehicle. Failuretofollow theserecommenda-
tions mayresult inshortened enginelifeand reduced
engine performance.
. Donot drive ataconstant speed,eitherfastor
slow ,for long periods oftime.
. Donot run theengine over4,000 rpm.
. Donot accelerate atfull throttle inany gear.
. Donot start quickly .
. Donot brake hardasmuch aspossible.
. Donot tow atrailer foratleast thefirst 800 km
(500 miles) (forAustralia andNew Zealand) .
GUID-E8B 3C646-A7 78-4313-AF 16-0B6BA360E 60C
WARNING:
The driving characteristic sof your vehicle will
change remarkably byany additional loadand
its distribution, aswell asby adding optional
equipment (roofracks, etc.). Your driving style
and speed mustbeadjusted according tothe
circumstances. Especiallywhencarrying heavy
loads, yourspeed mustbereduced adequately.
. Make surethearea around thevehicle isclear.
. Visually inspecttiresfortheir appearance and
condition. Measureandcheck thetire pressure for
proper inflation.
. Check thatallwindows andlights areclean.
. Adjust theseat andhead restraint positions.
. Adjust theinside andoutside rearview mirror
positions.
. Fasten yourseatbeltandaskallpassengers todo
the same.
. Check thatalldoors areclosed.
. Check theoperation ofthe warning lightswhen
the ignition switchisplaced inthe ªONº position.
. Maintenance itemsinthe ª8.Maintenance anddo-
it-yourselfº sectionshouldbechecked periodi-
cally .
GUID-31 CD6104-03 10-4DC0-AF3 7-02F08BEF2110
WARNING:
. Never leavechildren oradults whowould
normally requirethesupport ofothers alone
in your vehicle. Petsshould notbeleft alone
either. Theycould unknowingly activate
switches orcontrols andinadvertently be-
come involved inaserious accident and
injure themselves. Onhot, sunny days,
temperatures inaclosed vehicle could
quickly become highenough tocause se-
vere orpossibly fatalillness topeople or
animals.
. Properly secureallluggage tohelp prevent it
from sliding orshifting. Donot place lug-
gage higher thantheseatbacks. Inasudden
stop orcollision, unsecured luggagecould
cause personal injury.
NO TE:
During thefirst fewmonths afterpurchasing a
new vehicle, ifyou smell strong odorsofVolatile
Organic Compounds (VOCs)insidethevehicle,
ventilate thepassenger compartment thor-
oughly. Openallthe windows beforeentering
or while inthe vehicle. Inaddition, whenthe
temperature inthe passenger compartment
rises, orwhen thevehicle isparked indirect
sunlight foraperiod oftime, turnoffthe air
recirculation modeofthe airconditioner and/or
open thewindows toallow sufficient freshair
into thepassenger compartment.
BREAK-IN SCHEDULE BEFORESTARTING ENGINE PRECAUTI
ONSWHEN STARTING
AND DRIVING
&RQGLWLRQ


> (GLW   0RGHO &$@
5-4
Starting anddriving
GUID-365 EE49C-5FF 9-4447-845A-3881038 C5420
Driving yourvehicle tofitthe circumstances isessential
for your safety andcomfort. Asadriver, youshould be
the one who knows besthowtodrive inthe given
circumstances.
ENGINE COLDSTART PERIOD
GUID-B8 9C453D-A 996-4A1A-A8 96-4FC3520E6BFC
Due tothe higher engine speeds, whentheengine is
cold, extracaution mustbeexercised whenselecting a
gear during theengine warm-up periodafterstarting
the engine.
L OADING LUGGAGE
GUID-C66 3B3F6-8EAA- 46C6-9228-B 3141F69D6D3
Loads andtheir distribution andtheattachment of
equipment (couplingdevices,roofluggage carriers,
etc.) willconsiderably changethedriving character-
istics ofthe vehicle. Your driving styleandspeed must
be adjusted according tothe circumstances.
DRIVING INWET CONDITIONS
GUID-3D DDCE8B-46F7 -4220-938D-F02C21034A4A
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid following tooclose tothe vehicle infront.
When watercovers theroad surface withwater
puddles, smallwater streams, etc.,reduce speedto
prevent hydroplaning whichcancause skidding and
loss ofcontrol. Worn tires willincrease thisrisk.
DRIVING INWINTER CONDITIONS
GUID-393 9347B-E44 6-4695-87D1-257AFA202DC2
. Drive cautiously .
. Avoid accelerating orstopping suddenly.
. Avoid sharpturning orlane changing suddenly.
. Avoid sudden steering.
. Avoid following tooclose tothe vehicle infront.
GUID-91D DB153-CB CA-454D-B 139-A71B18FD2EDC
WARNING:
Never remove thekey orturn theignition switch
to the ªLOCKº position whiledriving. Thesteer-
ing wheel willlock andcould cause thedriver to
lose control ofthe vehicle. Thiscould result in
serious vehicledamage orpersonal injury.
CONTINUOUSL YVARIABLE TRANSMIS-
SION (CVT)
GUID-54 525C04-496 D-421C-8752-6B511BA 7402C
SSD0392
The ignition lockisdesigned sothat theignition switch
cannot beturned tothe ªLOCKº position untiltheshift
lever ismoved tothe ªPº (Park) position. Whenmoving
the ignition switchtothe ªLOCKº position, toremove
the key from theignition switch,makesuretheshift
lever isin the ªPº (Park) position.
When theignition switchcannot beturned tothe
ªL OCKº position:
1. Move theshift lever tothe ªPº (Park) position.
2. Turn theignition switchslightly inthe ªONº
direction.
3. Turn theignition switchtothe ªLOCKº position. 4.
Remove thekey.
If the ignition switchisturned tothe ªLOCKº position,
the shift lever cannot bemoved fromtheªPº (Park)
position. Theshift lever canbemoved ifthe ignition
switch isin the ªONº position withthefoot brake pedal
depressed.
The ªOFFº position
*
1
is between theªLOCKº and
ª ACCº positions, althoughitis not marked onthe
ignition switch.
MANUAL TRANSMISSION (MT)
GUID-21 B70D8F-F0 98-475A-A7 7E-979553 F48594
SSD0503
The ignition switchincludes adevice thathelps
prevent accidental removalofthe key while driving.
The keycan only beremoved whentheignition switch
is in the ªLOCKº position.
T o turn theignition switchtothe ªLOCKº position from
the ªACCº orªONº position, turnthekey tothe ªOFFº
position, pushthekey in,then turnthekey tothe
ªL OCKº position.
The ªOFFº position
*
1
is between theªLOCKº and
ª ACCº positions, althoughitis not labeled onthe
ignition switch.
CARE WHEN DRIVING IGNITION
SWITCH(model without
Intelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
STEERING LOCK
GUID-84FC5F 17-E3C7-4BE1-842B-2 338DC8B9E85
T o lock steering wheel
GUID-643 D9CDC-84 45-49BB-8146-1F81F862C0B9
1. Turn theignition switchtothe ªLOCKº position.
2. Remove thekey from theignition switch.
3. Turn thesteering wheel1/6ofaturn clockwise
from thestraight upposition.
T o unlock steering wheel
GUID-F9918 49F-1987-47 3E-AFAD-235CD 32C3712
1. Insert thekey into theignition switch.
2. Gently turntheignition switchwhilerotating the
steering wheelslightly rightandleft.
KEY POSITIONS
GUID-95C A75D5-0D2E -4FAF-BC0 D-63E3D92 C30B8
L OCK (0)
GUID-144 974C4-67B 8-4F45-92DA- 6954532EDEFE
The ignition keycan only beremoved atthis position.
The steering lockcanonly belocked atthis position.
OFF (1)
GUID-54 D824D0-1B74 -4475-84F5-CA80FB23D19C
The engine isturned offwith thesteering wheel
unlocked.
ACC (2)
GUID-17 E1619A-16C2 -4F88-A958-D19A38830 78C
The electrical accessory poweractivates withoutthe
engine turnedon.
ON (3)
GUID-8FAE5841-E613-460B-A9 14-0927C1C5B9A6
The ignition systemandtheelectrical accessory power
activate withouttheengine turnedon.
ST ART (4)
GUID-16D 5423F-AB9 6-440A-A9B2 -60948BDBB14C
The engine starteractivates andtheengine willstart.
The ignition switch,whenreleased, willautomatically
turn tothe ªONº position.
CAUTION:
As soon asthe engine hasstarted, releasethe
ignition switchimmediately.
GUID-8D8 CC42A-947 4-401D-AE63-E7B674 B40563
PRECAUTIONS ONPUSH-BUTT ONIGNI-
TION SWITCHOPERA TION
GUID-135 62CA9-9E1 B-4EA6-B47 6-DA4BA15F7D32
WARNING:
Do not operate thepush-button ignitionswitch
while driving thevehicle exceptinan emergency.
(The engine willstop when theignition switchis
pushed 3consecutive timesorthe ignition
switch ispushed andheld formore than2
seconds.) Thesteering wheelwilllock andcould
cause thedriver tolose control ofthe vehicle.
This could result inserious vehicledamage or
personal injury.
Before operating thepush-button ignitionswitch,be
sure tomove theshift lever tothe ªPº (Park) position
(for Continuously Variable Transmission model)orthe
shift lever tothe ªNº (Neutral) position(forManual
T ransmission model).
INTELLIGENT KEYSYSTEM
GUID-771FA3AD-C30C-4693-9 8E4-B9AE610D746B
The Intelligent Key system canoperate theignition
switch without takingthekey outfrom yourpocket or
bag. Theoperating environment and/orconditions may
affect theIntelligent Key system operation.
CAUTION:
. Besure tocarry theIntelligent Keywith you
when operating thevehicle.
. Never leavetheIntelligent Keyinside the
vehicle whenyouleave thevehicle.
. Ifthe vehicle battery isdischarged, the
ignition switchcannot beswitched from
the ªLOCKº position, andifthe steering lock
is engaged, thesteering wheelcannot be
moved. Chargethebattery assoon as
Starting anddriving
5-5
PUSH-BUT
TON IGNITION SWITCH
(model withIntelligent Keysystem)
&RQGLWLRQ


> (GLW   0RGHO &$@
5-6
Starting anddriving
possible. (SeeªJump startingº (P.6-5) .)
Operating range
GUID-80A4 4E43-0A1B -4ABB-A7E6-B D571734D53 C
SSD0436
The Intelligent Key can only beused forstarting the
engine whentheIntelligent Key iswithin thespecified
operating range
*
1
.
When theIntelligent Key battery isalmost discharged
or strong radiowaves arepresent neartheoperating
location, theIntelligent Key system's operating range
becomes narrowerandmay notfunction properly.
If the Intelligent Key iswithin theoperating range,itis
possible foranyone, evensomeone whodoes notcarry
the Intelligent Key ,to push theignition switchtostart
the engine.
. The luggage roomareaisnot included inthe
operating range,buttheIntelligent Keymay
function.
. Ifthe Intelligent Key isplaced onthe instrument
panel, insidetheglove box,door pocket orthe
corner ofthe interior compartment, theIntelligent
K ey may notfunction.
. Ifthe Intelligent Key isplaced nearthedoor or
window outsidethevehicle, theIntelligent Key
may function.
Continuously Variable Transmission (CVT)
model
GUID-59131E CE-A47C-4849-A212-5FF7051D7462
The ignition lockisdesigned sothat theignition switch
cannot beswitched tothe ªLOCKº position untilthe
shift lever ismoved tothe ªPº (Park) position. When
pushing theignition switchtothe ªOFFº position, make
sure theshift lever isin the ªPº (Park) position.
When theignition switchcannot beswitched tothe
ªL OCKº position:
1. Move theshift lever tothe ªPº (Park) position.
2. Push theignition switchtothe ªOFFº position.
3. Open thedoor. Theignition switchwillchange to
the ªLOCKº position.
If the ignition switchisswitched tothe ªLOCKº
position, theshift lever cannot bemoved fromtheªPº
(Park) position. Theshift lever canbemoved ifthe
ignition switchisin the ªONº position withthefoot
brake depressed.
STEERING LOCK
GUID-E05 63F6E-C5FD- 4C6A-83D7-9D 4CAE048AA9
The ignition switchisequipped withananti-theft
steering lockdevice.
T o lock steering wheel
GUID-199 0FCB9-1E4 5-4067-918 5-B54F6548 9D5D
1. Push theignition switchtothe ªOFFº position
where theignition switchposition indicator willnot
illuminate.
2. Open orclose thedoor. Theignition switchturns
to the ªLOCKº position.
3. Turn thesteering wheel1/6ofaturn tothe right or
left from thestraight upposition.
T o unlock steering wheel
GUID-836 CAB5B-2A97-4D4D-B A13-0D61A7DEAB3B
Push theignition switch,andthesteering wheelwillbe
automatically unlocked.
CAUTION:
. Ifthe battery ofthe vehicle isdischarged, the
push-button ignitionswitchcannot be
switched fromtheªLOCKº position.
. Ifthe ignition switchposition doesnot
change fromtheªLOCKº position, pushthe
ignition switchagainwhilerotating the
steering wheelslightly tothe right andleft.
IGNITION SWITCHPOSITIONS
GUID-787 88975-EF20-4EEC-9 BD9-C8FD 1F38789B
SSD0859
When theignition switchispushed withoutdepressing
the brake pedal (Continuously Variable Transmission
model) orthe clutch pedal(Manual Transmission
model) ,the ignition switchposition willchange as
follows:
. Push oncetochange toªACCº .
. Push twotimes tochange toªONº .
. Push three times tochange toªOFFº .
&RQGLWLRQ


> (GLW   0RGHO &$@
. Push fourtimes toreturn toªACCº .
. Open orclose anydoor toreturn toªLOCKº when
in the ªOFFº position.
The indicator light
*
A
on the ignition switchillumi-
nates whentheignition switchisin the ªACCº orªONº
position.
L OCK position
GUID-43425B BE-7F00-4ED4-A87 5-071702F2 842A
The ignition switchandsteering lockcanonly be
locked atthis position.
The ignition switchwillbeunlocked whenitis pushed
to the ªACCº position whilecarrying theIntelligent Key .
ACC position
GUID-202F5 141-00BE-47DC-B76C-7 268FE6DC636
The electrical accessory poweractivates atthis
position withouttheengine turnedon.
ON position
GUID-9FF5 AE68-135D-4 D67-8BBC-43E8DC881 23E
The ignition systemandtheelectrical accessory power
activate atthis position withouttheengine turnedon.
OFF position
GUID-81EA9 526-2AC3-4FF2-91B3 -F3E0BFFFA02D
The engine isturned offwith thesteering wheel
unlocked.
WARNING:
Never pushtheignition switchtothe ªOFFº
position whiledriving. Thesteering wheelmay
lock andcause thedriver tolose control ofthe
vehicle, resulting inserious vehicledamage or
personal injury.
CAUTION:
Do not leave thevehicle forextended periodsof
time when theignition switchisin the ªACCº or
ªONº position andtheengine isnot running. This
candischarge thebattery.
INTELLIGENT KEYBATTER YDISCHARGE
GUID-EC7 BC919-57B A-4B13-9C48-52E166 3770CA
SSD0860
If the battery ofthe Intelligent Key isdischarged, or
environmental conditionsinterferewiththeIntelligent
K ey operation, starttheengine according tothe
following procedure:
1. Continuously Variable Transmission (CVT)
model:
Move theshift lever tothe ªPº (Park) orªNº
(Neutral) position.
Manual Transmission (MT)model:
Move theshift lever tothe ªNº (Neutral) position.
2. Firmly depress thebrake pedal.
3. Touch theignition switchwiththeIntelligent Key
as illustrated. (Achime willsound.)
4. Push theignition switchwhiledepressing the
brake pedal (Continuously Variable Transmission
models) orclutch pedal(Manual Transmission
models) within10seconds afterthechime
sounds. Theengine willstart.
After step3is performed, whentheignition switchis
pushed withoutdepressing thebrake pedal (Con-
tinuously Variable Transmission models)orclutch pedal
(Manual Transmission models),the ignition
switch position willchange toªACCº .
NO TE:
. When theignition switchispushed tothe
ª ACCº orªONº position orthe engine is
started bythe above procedures, theIntel-
ligent Keysystem warning lightmayblink in
yellow evenifthe Intelligent Keyisinside
the vehicle. Thisisnot amalfunction. To stop
the warning lightfrom blinking, touchthe
ignition switchwiththeIntelligent Key
again.
. Ifthe Intelligent Keysystem warning lightin
the meter isblinking ingreen, replace the
battery assoon aspossible. (SeeªBatteryº
(P .8-18) .)
Starting anddriving
5-7
&RQGLWLRQ


> (GLW   0RGHO &$@
5-10
Starting anddriving
slowly whentheengine isrunning. Make
sure thefoot brake pedalisdepressed fully
and thevehicle isstopped beforeshifting
the shift lever.
. MAKE SUREOFTHE SHIFT LEVER POSI-
TION -Make suretheshift lever isin the
desired position. ªDºand ªLºor manual shift
mode areused tomove forward andªRºto
back up.
. WARM UPTHE ENGINE -Due tothe higher
idle speeds whentheengine iscold, extra
caution mustbeexercised whenshifting the
shift lever intothedriving position immedi-
ately afterstarting theengine.
Shifting
GUID-22528B F3-29D9-403E-AE79-B EA15D2F63 FE
JVS0199X
With manual shiftmode (RHD model)
JVO0030X
Without manualshiftmode (LHD model)

Push thebutton
*
A
while depressing the
foot brake
pedal.

Push thebutton
*
A
.

Just move theshift lever.
WARNING:
. Apply theparking brakeifthe shift lever isin
any position whiletheengine isnot running.
Failure todo socould cause thevehicle to
move unexpectedly orroll away andresult in
serious personal injuryorproperty damage.
. Ifthe shift lever cannot bemoved fromthe
ªPº (Park) position whiletheengine is
running andthefoot brake pedalisde-
pressed, thestop lights maynotwork.
Malfunctioning stoplights couldcause an
accident injuringyourself andothers.
After starting theengine, fullydepress thefoot brake
pedal, pushtheshift lever button andmove theshift
lever outofthe ªPº (Park) position.
If the ignition switchisplaced inthe ªOFFº orªACCº
position forany reason whiletheshift lever isin any positions
otherthantheªPº (Park) position, theignition
switch cannot beplaced inthe ªLOCKº position.
If the ignition switchcannot beplaced inthe ªLOCKº
position, performthefollowing steps:
1. Apply theparking brake.
2. Place theignition switchinthe ªONº position
while depressing thefoot brake pedal.
3. Move theshift lever tothe ªPº (Park) position.
4. Models withIntelligent Keysystem:
Place theignition switchinthe ªOFFº position.
Models without Intelligent Keysystem:
Place theignition switchinthe ªLOCKº position.
P (Park) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition whenthevehicle isparked orwhen
starting theengine. Makesurethatthevehicle is
completely stoppedandmove theshift lever into
the ªPº(Park) position. Applytheparking brake.
When parking onahill, first depress thefoot brake
pedal, applytheparking brake,andthen move theshift
lever intotheªPº (Park) position.
R (Reverse) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Use thisposition toback up.Make surethatthevehicle
is completely stoppedbeforeselecting theªRº
(Reverse) position.
N (Neutral) :
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
Neither theforward norreverse gearisengaged. The
engine canbestarted inthis position. You may shift to
the ªNº (Neutral) positionandrestart astalled engine
while thevehicle ismoving.
&RQGLWLRQ


> (GLW   0RGHO &$@
5-12
Starting anddriving
turn theSPORT modeoff.
Remember nottodrive athigh speeds forextended
periods oftime withtheSPORT modeinthe ªONº
position. Thisreduces fueleconomy .
Accelerator downshift-in the ªDº position -
GUID-FE4ECF FF-36B2-40BE-8768- DFB973246 910
For passing orclimbing hills,depress theaccelerator
pedal tothe floor. Thisshifts thetransmission down
into alower gear,depending onthe vehicle speed.
Shift lockrelease
GUID-7F 9F39D1-C CBB-4C10-9 90D-C12C1B 7B40EB
JVO0027X
Without manualshiftmode (LHDmodel)
If the battery charge islow ordischarged, theshift
lever maynotbemoved fromtheªPº (Park) position
even withthebrake pedal depressed andtheshift lever
button pushed.
T o move theshift lever, perform thefollowing
procedure:
1. Models withIntelligent Keysystem:
Place theignition switchinthe ªOFFº orªLOCKº
position.
Models without Intelligent Keysystem:
Place theignition switchinthe ªLOCKº position,
and remove thekey ifit is inserted. 2.
Apply theparking brake.
3. Push theshift lever button andmove theshift lever
to the ªNº (Neutral) positionwhileholding down
the shift lockrelease.
Place theignition switchinthe ªONº position tounlock
the steering wheel.Thevehicle maybemoved tothe
desired location.
For model withIntelligent Key system: Ifthe battery is
discharged completely,the steering wheelcannot be
unlocked. Donot move thevehicle withthesteering
wheel locked.
If the shift lever cannot bemoved outofthe ªPº (Park)
position, haveaNISSAN dealerchecktheCVT system
as soon aspossible.
WARNING:
If the shift lever cannot bemoved fromtheªPº
(Park) position whiletheengine isrunning and
the brake pedalisdepressed, thestop lights
may notwork. Malfunctioning stoplights could
cause anaccident injuringyourself andothers.
High fluidtemperature protectionmode
GUID-92F6 203D-4431 -412E-BD73-BE0106E 26143
This transmission hasahigh fluidtemperature protec-
tion mode. Ifthe fluid temperature becomestoohigh
(for example, whenclimbing steepgrades inhigh
temperature withheavy loads, suchaswhen towing a
trailer) ,engine powerand,under someconditions,
vehicle speedwillbedecreased automatically to
reduce thechance oftransmission damage.Vehicle
speed canbecontrolled withtheaccelerator pedal,
but engine andvehicle speedmaybelimited.
Fail-safe
GUID-4C5CA0 11-BE46-48EA-A16F-D6 F3A9BF72B8
When thefail-safe operation occurs,theCVT willnot
be shifted tothe selected drivingposition.
If the vehicle isdriven underextreme conditions,
such asexcessive wheelspinning andsubse-
quent hardbraking, thefail-safe systemmaybe
activated. Thiswilloccur evenifall electrical
circuits arefunctioning properly.Inthis case,
place theignition switchinthe ªOFFº position
and wait for10seconds. Thenturntheignition
switch backtothe ªONº position. Thevehicle
should returntoits normal operating condition.
If itdoes notreturn toits normal operating
condition, haveaNISSAN dealercheckthe
transmission andrepair itifnecessary.
WARNING:
When thefail-safe operation occurs,vehicle
speed maybegradually reduced.Thereduced
speed maybelower thanother traffic,which
could increase thechance ofacollision. Be
especially carefulwhendriving. Ifnecessary, pull
to the side ofthe road atasafe place andallow
the transmission toreturn tonormal operation,
or have itrepaired ifnecessary.
&RQGLWLRQ