light NISSAN PULSAR 2018 Manual Online


> (GLW   0RGHO &$@
GUID-B6 C972E1-44C7 -4B02-9DB2-A30BF24E457A
CAUTION:
. Do not ground accessories directlytothe
battery terminal. Doingsowill bypass the
variable voltagecontrolsystemandthe
vehicle battery maynotcharge completely.
. Use electrical accessories withtheengine
running toavoid discharging thevehicle
battery.
Y our vehicle isequipped withavariable voltagecontrol
system. Thissystem measures theamount ofelectrical
discharge fromthebattery andcontrols voltage
generated bythe alternator.
GUID-9514CE EE-B80E-4951-BA34-D456909231DC
ENGINE COMPARTMENT
GUID-2566CF 78-9D09-4E62-BA83-F DDD99EB8 FFB
SDI2654
CAUTION:
Never useafuse ofahigher orlower amperage
rating thanthatspecified onthe fuse boxcover.
This could damage theelectrical systemor
cause afire.
If any electrical equipment doesnotoperate, checkfor
an open fuse.
1. Be sure theignition switchisin the ªOFFº
position.
2. Besure theheadlight switchisin the ªOFFº
position.
3. Open theengine hood.
4. Remove thefuse/fusible linkbox cover bypushing
the tab
*
1
and lifting thecover fromtheright side
*
2
, then theleftside
*
3
.
5. Locate thefuse thatneeds tobe
replaced.
SDI1754
6. Remove thefuse using thefuse puller located in
the passenger compartment.
7. Ifthe fuse isopen
*
A
, replace itwith anew fuse
*
B
.
If the new fuse alsoopens, afterinstalling, havethe
electrical systemchecked, andifnecessary repaired,
by aNISSAN dealer.
The holder
*
4
also contains thefuses. Forchecking
and/or replacing, seeaNISSAN dealer.
Fusible links
GUID-E01 1CEDE-E1 DF-4E53-A5 B4-49B72B7 3D3E5
SDI2642
If any electrical equipment doesnotoperate andthe
fuses areingood condition, checkthefusible linksin
Maintenance anddo-it-yours elf
8-21
V
ARIABLE VOLTAGE CONTROL
S Y STEM (ifequipped) FUSES
&RQGLWLRQ


> (GLW   0RGHO &$@
8-22
Maintenance anddo-it-yours elf
the holders
*
1
and
*
2
. If any ofthese fusible linksare
melted, replace onlywith genuine NISSAN parts.
For checking andreplacing thefusible linksinholders
*
2
, see aNISSAN dealer.
P ASSENGER COMPARTMENT
GUID-A499C 18A-796A-46C2-94E3-5 43D1870676 0
JVM0184X
CAUTION:
Never useafuse ofahigher orlower amperage
rating thanthatspecified onthe fuse boxcover.
This could damage theelectrical systemor
cause afire.
If any electrical equipment doesnotoperate, checkfor
an open fuse.
1. Be sure theignition switchisin the ªOFFº
position.
2. Besure theheadlight switchisin the ªOFFº
position.
3. Remove thefuse boxcover
*
1
.
4. Locate thefuse thatneeds tobe replaced.
5. Remove thefuse using thefuse puller
*
2
.
SDI1754
6. Ifthe fuse isopen
*
A
, replace itwith anew fuse
*
B
.
If the new fuse alsoopens, afterinstalling, havethe
electrical systemchecked, andifnecessary repaired,
by aNISSAN dealer.
&RQGLWLRQ


> (GLW   0RGHO &$@
Extended storagefuseswitch (ifequipped)
GUID-5C0 0252D-3068-4605-8AA0 -2F3EB6F6A1 1D
SDI2705
If any electrical equipment doesnotoperate, remove
the extended storagefuseswitch andcheck foran
open fuse.
NO TE:
If the extended storagefuseswitch malfunc-
tions, orifthe fuse isopen, itis not necessary to
replace theswitch. Inthis case, remove the
extended storagefuseswitch andreplace itwith
a new fuse ofthe same rating.
How toremove theextended storagefuse
switch:
GUID-9E14C2 E6-2E9C-4731-980B-C45B899B9 77B
1. To remove theextended storagefuseswitch, be
sure theignition switchisin the ªOFFº orªLOCKº
position.
2. Besure theheadlight switchisin the ªOFFº
position.
3. Remove thefuse boxcover.
4. Pinch thestorage fuseswitch andpullitin the
direction illustrated.
GUID-0CA4 CBD7-552D -4275-8986-132CF6D FB30B
HEADLIGHTS
GUID-2A2B 2E01-3752-481E-ADE 0-0FB5E738 13F7
Fog may temporarily forminside thelens ofthe exterior
lights inthe rain orinacar wash. Atemperature
difference betweentheinside andtheoutside ofthe
lens causes thefog. This isnot amalfunction. Iflarge
drops ofwater collect insidethelens, contact a
NISSAN dealer.
X enon headlight model
GUID-A 9B63013- 3258-4FA3-B5A7 -51CE4118ED 89
If replacement isrequired, contactaNISSAN dealer.
WARNING:
HIGH VOLTAGE
When xenon headlights areon,they produce a
high voltage. To prevent anelectric shock,never
attempt tomodify ordisassemble. Alwayshave
your xenon headlights replacedataNISSAN
dealer.
Use thesame number andwattage asoriginally
installed:
High/Low beams(Xenon)
Wattage: 35
Bulb no.:D2S
Halogen headlight model
GUID-211 3779C-896 9-4483-818 E-EFB621042A37
The halogen headlight isasemi-sealed beamtype
which usesreplaceable headlight(halogen) bulbs.
They canbereplaced frominside theengine compart-
ment without removing theheadlight assembly.
CAUTION:
High-pressure halogengasissealed insidethe
bulb. Thebulb maybreak ifthe glass envelope is
scratched orthe bulb is
dropped.
JVM0070X
1. Disconnect thebattery negative cable.
2. Disconnect theelectrical connector
*
A
from the
rear endofthe bulb.
3. Pulloffthe rubber cap
*
B
.
4. Push andturn theretaining pin
*
C
to loosen it.
5. Remove theheadlight bulb.Donot shake orrotate
the bulb when removing it.
6. Install thenew bulb inthe reverse orderof
removal.
Maintenance anddo-it-yours elf
8-23
LIGHTS
&RQGLWLRQ


> (GLW   0RGHO &$@
8-24
Maintenance anddo-it-yours elf
CAUTION:
. When handling thebulb, donot touch the
glass envelope.
. Donot leave thebulb outofthe headlight
reflector foralong period oftime asdust,
moisture andsmoke mayenter theheadlight
body andaffect theperformance ofthe
headlight.
Use thesame number andwattage asoriginally
installed:
Halogen headlight model
High/Low beambulb:60W/55W (H4)
Aiming adjustment isnot necessary ifonly thebulbs
are replaced. Whenaiming adjustment isnecessary ,
contact aNISSAN dealer.
EXTERIOR LIGHTS
GUID-A 39ABF0E-9793 -4A72-8940-2C4F41 CC93E8
Item Wattage (W)
Front turnsignal light 21
Front clearance light 5
Front foglight (ifequipped) 35
Side turnsignal light
Fender type 5
Outside rearview mirror
type* LED
Rear combination lights
T urn signal 21
Stop/tail light 21/5
Reverse light 21
High-mounted stoplight* LED
License platelight 5
*: See aNISSAN dealerforreplacement.
INTERIOR LIGHT
GUID-F 16248C6-84 48-48CC-A9 07-253EFE587A2A
Item Wattage (W)
Room light 8
Map light 8
V anity mirror light(ifequipped) 1.8
Cargo roomlight 5
&RQGLWLRQ


> (GLW   0RGHO &$@
LIGHT LOCA TIONS
GUID-1973B 783-D758-4430-9B7D-C0DCAC417 CD8
JVM0263X
1. Maplight
2. Room light
3. Front foglight*
4. Front turnsignal light
5. Headlight (high-beam/low-beam)
6. Clearance light
7. Sideturnsignal lights(onthefront fender orthe
outside rearview mirror)
8. High-mounted stoplight
9. Cargo roomlight
10. License platelight
11. Reverse light
12. Rearturnsignal light
13. Stop/tail light
*: ifequipped
Maintenance anddo-it-yours elf
8-25
&RQGLWLRQ


> (GLW   0RGHO &$@
8-26
Maintenance anddo-it-yours elf
Replacement procedures
GUID-48FF C193-56B1 -491E-B974-207C25ED 351B
SDI1805

REMOVE

INST ALL
All other lights areeither typeA, B, Cor D. When
replacing abulb, firstremove thelens and/or
cover.
JVM0074X
Front turnsignal light
JVM0075X
Clearance light
&RQGLWLRQ


> (GLW   0RGHO &$@
JVM0072X
Front foglight (if equipped)
SDI2445
Side turnsignal light(fender type)
JVM0071X
Rear combination light
T o replace therear combination lightbulbs:
1. Remove thenuts
*
A
and move therear
combination light
*
B
rearward tomake a
clearance, thencarefully prythe light using a
suitable tool.
2. Replace thebulbs. (Stop/tail light
*
3
, Turn signal
light
*
2
, Reverse light
*
1
)
3. Install thecombination lightinthe reverse orderof
removal.
Maintenance anddo-it-yours elf
8-27
&RQGLWLRQ


> (GLW   0RGHO &$@
8-28
Maintenance anddo-it-yours elf
JVM0073X
License plate light
JVM0318X
Map light
SDI1499A
Room light
SDI1839
V anity mirror light(ifequipped)
&RQGLWLRQ


> (GLW   0RGHO &$@
SDI2653
Cargo roomlight
LEGAL REQUIREMENT TO ADJUST HEADLIGHT BEAM(Halogen headlightmodel)
GUID-0F C3C854-D96 A-4F2B-ABAB -4262F03C FE47
JVM0247X
Left-Hand Drive(LHD) models
Maintenance anddo-it-yours elf
8-29
&RQGLWLRQ


> (GLW   0RGHO &$@
8-30
Maintenance anddo-it-yours elf
JVM0248X
Right-Hand Drive(RHD) models
When thevehicle isdriven inacountry wherethe
driving laneisdifferent toyour home country ,affix an
opaque stickeronthe headlight.
1. Turn theignition switchtothe ªOFFº position and
wait until theheadlights cooldown.
2. Prepare thestickers referring tothe figure. Make
the stickers
*
A
that willbeaffixed tothe surface
of the right sideheadlight andtheleftside
headlight. NO
TE:
.
Use anopaque material thatprevents the
light from passing through it.
.
Note thatother transparent materialsdo
not work effectively.
3. Affix thesticker byaligning thecorner
*
B
of the
sticker withtheposition ofthe mark
*
C
that is
located onthe surface ofthe headlight seenfrom
front.
Affix thesticker asillustrated byaligning themark
*
C
with dividing lines
*
D
and
*
E
.
NO TE:
Align themark
*
C
with thecenter mark
of the headlight bulb.
&RQGLWLRQ