torque NISSAN PULSAR 2020 Owners Manual


> (GLW   0RGHO &$@
2. Carefully putthespare tireonand tighten the
wheel nutswithyour fingers. Checkthatallthe
wheel nutscontact thewheel surface horizontally .
3. Tighten thewheel nutsalternately andevenly in
the sequence illustrated(
*
1
-
*
5
) , more than2
times withthewheel nutwrench, untilthey are
tight.
4. Lower thevehicle slowlyuntilthetire touches the
ground.
5. Tighten thewheel nutssecurely ,with thewheel
nut wrench, inthe sequence illustrated.
6. Lower thevehicle completely .
Tighten thewheel nutstothe specified torque
with atorque wrench assoon aspossible.
Wheel nuttightening torque:
108 N´m (11kg-m, 80ft-lb)
The wheel nutsmust bekept tightened to
specification atall times. Itis recommended
that thewheel nutsbetightened tospecification
at each lubrication interval.
WARNING:
Retighten thewheel nutswhen thevehicle has
been driven for1,000 km(600 miles) (alsoin
cases ofaflat tire, etc.).
ST OWING DAMAGED TIREANDTOOLS
GUID-1FAB B527-F376-4605-B0E 8-545A3C1B479F
WARNING:
Be sure thatthetire, jack andtools usedare
properly storedafteruse.Such items can
become dangerous projectilesinan accident or
sudden stop.
1. Securely storethejack, tools andthedamaged
tire inthe storage area.
2. Replace thecargo floorboard.
3. Close theback door.
GUID-CA 3FC571-40 A7-4E0F-A6D6-412F4AB 6C190
WARNING:
. Incorrect jumpstarting canlead toabattery
explosion. Thebattery explosion mayresult
in severe injuryordeath. Itmay also result in
damage tothe vehicle. Besure tofollow the
instructions inthis section.
. Explosive hydrogengasisalways present in
the vicinity ofthe battery. Keepallsparks
and flames awayfromthebattery.
. Always wearsuitable eyeprotection and
remove rings,bracelets, andanyother jew-
elry whenever workingonornear abattery.
. Never leanover thebattery whilejump
starting.
. Never allowbattery fluidtocome into
contact witheyes, skin,clothes orthe
vehicle's paintedsurfaces. Batteryfluidisa
corrosive sulfuricacidwhich cancause
severe burns.Ifthe fluid comes intocontact
with anything, immediately flushthecon-
tacted areawithplenty ofwater.
. Keep thebattery outofthe reach ofchildren.
. The booster batterymustberated at12
volts. Useofan incorrectly ratedbattery will
damage yourvehicle.
. Never attempt tojump startafrozen battery.
It could explode andcause serious injury.
In case ofemergency
6-5
JUMP
STARTING
&RQGLWLRQ


> (GLW   0RGHO &$@
8-10
Maintenance anddo-it-yours elf
Engine oiland filter
GUID-5F 013F78-E E34-4C18-B FFB-79938 408A1A2
JVM0161X
MRA8DE engine model
SDI2652
MR16DDT engine model
JVM0081X
MRA8DE andMR16DDT engine model
SDI2722
HR16DE enginemodel
*
1
Oil filler cap
*
2
Oil drain plug
*
3
Oil filter
1. Place alarge drainpanunder thedrain plug.
2. Remove thedrain plugwithawrench.
3. Remove theoilfiller capand completely drainthe
oil.
If the oilfilter isto be changed, removeand
replace itat this time.
CAUTION:
Waste oilmust bedisposed ofproperly. Check
your local regulations.
4. Loosen theoilfilter withanoilfilter wrench.
5. Remove theoilfilter byturning itby hand.
6. Wipe theengine oilfilter mounting surfacewitha
clean cloth.
Be sure toremove anyoldgasket remaining onthe
mounting surface.
7. Apply newengine oiltothe gasket ofthe new oil
filter.
8. Screw inthe oilfilter untilaslight resistance isfelt
and then tighten anadditional 2/3ofaturn to
secure thefilter.
Oil filter tightening torque:
15 to20 N´m
(1.5 to2.0 kg-m, 11to15 ft-lb)
9. Clean andreinstall thedrain plugandnew washer.
Securely tightenthedrain plugwithawrench. Do
not use excessive force.
Drain plugtightening torque:
29 to39 N´m
(3.0 to4.0 kg-m, 22to29 ft-lb)
10. Refill therecommended engineoiland quantity .
(See ªRecommended fluids/lubricantsandcapa-
citiesº (P.9-2) .)
When fillingtheengine oil,donot remove
the dipstick (exceptforHR16DE engine
model) .
11. Securely installtheoilfiller cap.
&RQGLWLRQ